Reviews
I really wasn't going to buy this, but ….
Open endGrip requiredType
I used to use a Type that drilled Screw holes in Throttle, but I wonder why it was discontinued.
Quantity:Pair (for Left and Right) Both Material inside the bar:The aluminum tube is inserted and the screw is tightened to open the tube, so it must be re-tightened often or it will suddenly fall out while driving.
For this reason, the Throttle side must also be changed to an open end one.
Completely Material:It is aluminum and weighs almost nothing, so it can be used with or without use with little or no change in sensation.
View detail
Installed during handlebar replacement
I installed it on my HUSQVARNA TE250 2017 which I always use for forest road Touring.
This Bar End can be used for both large and small inner diameters by changing the Adapter.
I didn't like the Bar End that popped out so much, so this thin Bar End was very Balanced and just right.
View detail
Buy.
Well, it's a classic.
Buy!
MFJ Race may fail vehicle inspection in Regulation.
Confirmation.
View detail
The size was perfect!
I used it on the Grip end side with the Grip heater on my CL500. The OEM handlebar end has female threads and can be installed perfectly with the included bolts. View detail
Accent and minimum defense Up
I use it on my car KLX250es, I replaced the handlebar with zeta cx bar mx412Blue, so I bought it to match the color.
It is not only good looking, but it is also effective in protecting the throttle cone in case of a fall.
View detail
Purchased 29mm for Motorcycle
I purchased 29mm for Motorcycle.
The other companies' products are usually 32 to 35mm in diameter and large in size, but ZETA's product is also available in 29mm, so it can be used for bicycles as well.
View detail
Slider effect is not so strong.
I think the Slider effect is not so strong, but the Designability is good.
There has been no fading in about one to two years.
View detail
Stylish and easy installation
I bought the KLX230R to protect the bar end as well as to block the bar end hole when the hand guard is removed. 35mm large to prevent sand and mud from entering the throttle tube.
The anchor is for aluminum handlebar and for steel handle with large inner diameter, so it can be installed on KLX230R NORMAL steel handle without any additional parts. So it is good that it can be installed on the NORMAL steel handle of KLX230R without any additional parts.
A transparent plastic washer is also included to prevent sand and mud from penetrating the throttle tube. This is a very kind product.
View detail
The smallest claim, but the largest defense.
I used it on my 97 KLX250es. I use it widely from commuting to course, so a broken Throttle cone is fatal.
This time I used zeta cx bars and drc open end grips, 29mm, which is great for me because I feel no discomfort when I hold the grips.
View detail
zeta bar end
Item was excellent.shipping was fast.item was in good condition. will order more in future.pricing was reasonable.. View detail
For Dress-up and Bar End protection
good point
Cool.
A bad point
Aluminum, so it looks weak.
Not cheap.
Purchased to replace Handlebar on CROSS Gov.
Colorful, so it will be Accent as One point.
I did not understand the selection of Spacer for a moment because there is no instruction manual. However, I think it will be no problem once I have the actual product.
When installing, it is necessary to tighten the screws and open the spacer before installation; otherwise, it will spin forever unless it is inserted with just enough fine adjustment to just barely fit in the handlebar without spinning.
All Material:It's aluminum, so it's going to fall apart as soon as I knock it over.
View detail
The next thing you know, they're gone.
The detents are co-spinning during installation. It is tightened to some extent, but it is not removed due to vibration.
Tighten it to the same diameter as the inside diameter of the Handlebar before installation, and tap it in with a plastic hammer to make it easier to tighten.
View detail
Fits: KAWASAKI Ninja 650, KAWASAKI Z1000 (water-cooled), KAWASAKI Z250 (2013-), KAWASAKI ER-4n, KAWASAKI ER-6f, KAWASAKI ZZR1400 (ZX-14), KAWASAKI ZZR1200, KAWASAKI ZX-9R, KAWASAKI ZX-7RR, KAWASAKI ZX-7R, KAWASAKI ZX-6RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI ZX-12R, KAWASAKI ZX-10R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200 S, KAWASAKI ZRX1200 R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100
Two-tone color is good
While other manufacturer's products have a single color for the large body, this one has a two-tone color and a good texture.
However, it is not that heavy, so it may be better not to install it for vibration reduction purposes.
View detail
Although it is parts of an off vehicle, it uses for SR. Although green was chosen according to the color of a car body,
Although it is parts of an off vehicle, it uses for SR.
Although green was chosen according to the color of a car body,
View detail
Fits to Kawasaki Ninja 250R and Z400
[How is it used?
Both Ninja250R and Z400 are mainly used for touring.
The Ninja 250R is used on the end of a Penske Separate handle with an inner weight.
Z400 is used with ZETA CX Handlebar ends.
The Ninja 250R has been used for about 4 years and the Z400 for about 3 months.
Size is 29mm for both.
Was the one you received as per Image?
I am satisfied with the Large change in color and finish of Anodized as per Image.
The machining accuracy of the contact surface with the handlebar is good, and the contact is firm.
Was the installation difficult?
When installing the Ninja 250R, the bolt that came with the Ninja 250R was not long enough to accommodate the inner weight, so we were able to prepare a pot screw. (+head) Therefore, we worked carefully not to lick the screw head when tightening it.
On Z400, it can be easily installed with the included Bolt.
How was your experience with it?
This Bar End is characterized by its flat shape and I am a good looking person. (Wide flat surface and strong Impact) and falls, and prefer to use it because they think it is a functional Merit.
Anodized colors and hold up well and are visually satisfying.
As for the Merit in the event of a fall, the flat shape of the handlebar prevents it from being caught on the road surface, and since it slides down, it is considered to be less damaging to the handlebar. (If the shape is sharp, Moment may occur due to catching and the Handlebar may bend.)
Although it was not me, my wife and the owner of Ninja250R suffered a standing fall and a slipdown, respectively, but there was no damage to the handlebar and it served its purpose well.
Naturally, the Damage to the Body is firm, so if it is scraped by a fall, it is recommended that it be replaced before injury occurs.
[Included Parts:were they on?
Bolt、Anchor、Material:PlasticWasher
[Was there anything that disappointed you?
None
Point and hang of installation
The key hang in removing the OEMBar End is how to remove the Screw lock agent.
Although tools are required, the Screw lock agent will loosen when heated, so if the OEMBar End can be discarded, the fastest and surest way is to cure the Grip with wet Toweletc. and burn it with a Burner.
If you have a Solder iron, you can slowly heat the Screw part.
For +head Screw, a Shock driver would be perfect.
View detail
It is good
A It will be the Accent around the little Handlebar.
Functionally, it's kind of whatever you want it to be.
It feels like a color touch and improves the look and feel.
The Handlebar will also prevent it from being scraped off when it falls over.
It has been surprisingly helpful.
View detail
I made my choice based on looks alone.
If you're looking for durability and Guardability in a Bar End, this is not the product for you.
In my case, I chose the Grip for its appearance and the fact that I felt comfortable gripping the end part of the Grip.
I had installed it on another vehicle before, but depending on the Handlebar inner diameter, the installation tends to be loose.
It is necessary to use Rubber tape in combination.
By the way, I couldn't install it on the STD Handlebar of SR400 because it was too big.
Rubber tape was wrapped very thickly and then installed.
If you install it so tight that you can't turn it easily with your bare hands, it will be hard to come off.
View detail
Fits: YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ6-S Feather, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA FZ6-S Feather, YAMAHA FZ6-S Feather
Authentic construction at a reasonable price
I used it on my previous FZ1, and it was an excellent product, larger in width than OEM, with a beautiful Gold Anodized, zeta Material.:Aluminum products are cheaper than other companies, and the construction is solid, so I own several MOTARD and Trail bikes, but I choose zeta products for the large half of aluminum parts. I recommend it because of its outstanding stability and solid quality. View detail
This Bar End is perfect for Off-road.
Needless to say, this one is perfect for off-road use. It is lightweight and protects the ThrottleGrip firmly, even though the protrusion is the smallest limit. The Gratler Big Boy is used exclusively for off-road use on snow-covered roads, so I ignore the on-road use completely and use this one. View detail
Bar end plug
This is the third time i purchase Zeta bar end set. It is for spare. Ordered the item for GROM. Colour RED. Quality is fantastic. Fitment is perfect. Installation work is easy. Highly recommended item. View detail