Reviews
Wind protection~.
Scooter。
I used it for another car model. I installed it to deal with the wind hitting my stomach.
It's not bad at all.
Convenient angle adjustment. Adjustment is made while controlling the passage of air and taking balance of back pressure.
I'll take it off in the summer (laughs).
View detail
CROSSCUB110 looks different.
Installation is structured to attach to the part from which Mirror was removed.
The work itself should be no problem if you check the Instruction Manual.
Clamp Bar of Φ22.2×58mm is included so that Smartphone Holderetc. can be attached.
Bad points and points to note when installing
Shield's cut-out process does not seem to be a machine, so Quantity:Pair (for Left and Right) It was not symmetrical.
Since the bracket itself is not connected, the Shield is inevitably distorted when installed.
Mirror vibrates when stopped due to the use of a collar attached to the Mirror Bracket.
The bracket part using M10×40mm Flange bolt with Serrete (with a loosening stop on the back of the Flange) that comes with the kit will be scratched. It is better to install it with Washer because it may cause rust.
View detail
Grab it by the hand and yay!
Regarding installation, the difficulty of the work itself is not high at all.
but it will be a very tough fight if you try to do it alone.
Tentatively position the ScreenBody while fingering the ridiculously hard Clamp, and
Tightening the lock nut of the clamp was a tough job.
It is also better to have Pliers when crushing the Handlebar Clamp. Prepare them.
As for the effect, the flow of wind certainly seems to have changed, and the Wind Cutting sound has increased.
Depending on Rider's height and shape, I think I have increased turbulence around Helmet.
During rainfall, we expect it to reduce the burden on the upper body.
As for the fitting, I adjusted the position by loosening the bolt and adjusting the position→tightening the bolt again and again.
We are convinced that this is probably the correct adjustment method.
The bracket from the handlebar clamp is large and weak, and it shakes a lot while riding.
It was stated that the Clearance on the CowlWindshield should take 8mm, but this will definitely interfere while driving.
Hand in hand, yay!" We recommend taking Clearance more widely in
The Quality of the Screen itself is good Large variation.
*All photos are taken at the angle of most lying down.
View detail
Must-have item for CROSS CUB!
Purchased for CROSS CUB (JA60). My Cub is PearlDeepMud gray, Color:Gray and Black are the base color. [Color] We chose Smoke. The front disc brake cover, which is not shown in the photo, is attached, and I feel that it increases the sense of toughness, which I like from a design standpoint. One point is that the position of the back mirror is 2cm higher than the front one, which is a bit annoying. On the other hand, I think it is nice that it is 3cm closer to the inside of the Shield. The position of the Shield is shown on the inside of the Shield. "CC110. I bought it for its design, but after installing it, the wind blowing against my chest was reduced to Large width, and the coldness in winter was totally different. I am glad I bought this product. View detail
Bracket is difficult to attach
I used it on my CROSS CUB and the quality of the bracket was not as good as the zeta one, even with the paint and polish. The bracket is not as good as the zeta one, but it's not as easy to put on the handlebar. I had to change to zeta because of the Rust after a while. View detail
Bigger than I thought. Looks like a good windbreak.
I had a MINIVisor on my BANDIT250, but it was getting too cold. So, I transplanted the mra screen that I had on my gsxs125 to the BANDIT and put this DAYTONA screen for GROM on the gsxs! (Based on the diversion information of others on Net) It's bigger than I imagined. It is bigger than I imagined. I couldn't lay it down very well. I haven't ridden it yet because of the snow, but I can expect a windproof effect. View detail
It is also expected to be windproof.
I installed it somehow.
I compared them with each other and decided on this one.
Tourer, is it starting to become an Adventure type thing?
View detail
No complaints!
Some reviewers said there were a lot of parts, and the Image looked like a hassle...
If we assembled it beforehand after it arrived, all we had to do was pop it on the car body.
However, if you try to do the same timing from opening to installation, I think you'll feel that way because you'll spend more time assembling it.
I used to use the Asahi Windshield product before, but the Daytona product seems to be better for compatibility with the Zita Hand guard.
Paint on the front of the meter to prevent the shield from being distorted by the tightening of the bolts. "CC110. It's a good idea to fix it in a position that won't distort the image of the letters of
View detail
A windshield for form's sake
It's cold, it's cold, and the windbreak is on my neck, but I like Parenthesis It's a good idea to hide the instruments and navigation in here
Phone mounting bar is Quantity:Pair (for Left and Right) I want you to be connected
View detail
Measures against cold in winter
Since I used to love DAYTONAScreen from the former type LEAD, I did not hesitate and even buy a new type LEAD. Shape etc. , Rectification is an item being considered, but slightly dissatisfied because the shape of the front mold was good.
Mounting.... Hard to understand
View detail
Bracket - - - -
Because the Shield itself is well done, there is a feeling that it is ruined because the Fit feeling is bad with chat bracket and the vibration also goes out considerably. As a product it is a very regret goods. View detail
It was correct and installed
About installation
- Required tool
10 mm Double-end Wrench Quantity : 2 pc, 12 mm Double-end Wrench, 13 mm Socket wrench (Although 13 mm Glasses is OK, it will be difficult to obtain) , 4 mm Hexagonal Wrench.
- installation method
You can do it according to the Instruction Manual, but it is easier to work if you change only one place. According to Instruction Manual Shield Body "ShieldBracket" When "AdjustBracket" After installing "Handlebar Clamp" It is fixed with Bolt to. But this approach is quite difficult with one person's work.
So change it like this. In Shield "ShieldBracket" Only, "AdjustBracket" It is "Handlebar Clamp" I will temporarily fix it. Finally "AdjustBracket" When "ShieldBracket" To overlap and fix. Once the position of the shield is decided, once you finish tightening each part, it is finished.
- Others
This product can adjust the angle of the shield's angle within the range of 10 degrees. But in the most occuring position "ShieldBracket" When "AdjustBracket" Is the smallest area and the vibration and the wind become considerably large by the influence of Engine and wind. In the state that it is the most laid, the mating surface of the two Brackets becomes the largest Large and vibration is considerably reduced. Also, I think Shield looks better if it is the most sleepy.
This Windshield seems that Grom's car rank got up one by one.
Impressions of running
I realized that the actual size is bigger than the image. The height of Windshield almost reaches the upper end of Back Mirror. My height (170 cm) The usual Riding form prevents the wind to the chest and abdomen. In the lid body, only the Helmet goes up from the upper end of Windshield. It does not interfere with vision in every situation.
View detail
Wind removal effect? ??Visual effect 0
Try using it last autumn
Although it is easy to install with the size that covers the periphery of Meter of CROSSCUB, because Shield is easy to twist at the time of tightening Screw, it takes time if less tools are needed, and the mounting position of Mirror changes on Bracket, so the Mirror width is slightly narrow It becomes bad after reflection
The vibration caused by the vibration is as it is, but it is not terrible not to bother running
As a result of the Size, the amount of wind that corresponds to Helmet increases, the wind cutting sound gets annoying, in the winter, cold air comes around the chest firmly and it cools down and it gets firmly wet if it rains.
Since it looks solid, it is effective as a Dress-up product Large
View detail
I felt windproof effect more than I thought
I am wearing it a while ago..
Because it is a person who starts working without reading Instruction Manual so much, Quantity : Pair (for Left and Right) It took extra time due to wrong direction or wrong direction.
If you were reading the Installation Instruction Manual first, you could have completed work on Smooth.
The windshield seems to be bad, but now I think that the product is Stylish.
The dissatisfaction at this point is that the body mounting part (Original Mirror root) There are no hidden parts such as RubberBoots in.
I attach the original Mirror to the Bracket, but you can see the lower screw.
Today I ran less than 200km.
Although I ride in a few months, the wind that hits the body obviously is getting less.
It may be natural because it is Windshield, but it does a better job than I thought.
Large satisfied with windproof effect.
By the way, I am sleeping in the adjustment range.
There are points that I was interested in.
Bow to accelerate and hit Helmet's Shield to Windshield.
Well, is this any help?
Windshield I will try to attach Door Mole for Vehicle so that it does not damage Helmet 's Mirror shield.
View detail
I feel good!
I was worried a lot after seeing your Impression, but it is getting cold so I decided to install it. Since the commodity arrival was after sunset, all temporarily assembled and the first day finished. Although I often carried out the installation the next day, I was worried that the position of Mirror would be changed
I managed to solve the problem for some reason. The wind does not hit the chest that I noticed running, but the top of Helmet is amazing!
Well OK if you change Position slightly.
Working time was about 30 minutes for installation and about 30 minutes to prepare Mirror.
View detail
Sunglasses of the night
When assembling, remove Mirror first, after temporarily assembling in the room, I think that it is easier to attach it to the car body.
When installing Quantity : Pair (for Left and Right) Even if temporarily fastened to the object Bracket moves when retightening again, tighten several times. Quantity : Pair (for Left and Right) It might be earlier if you tighten little by little.
Apart from likes and dislikes, CROSSCUB's unique jumping Meter is hidden in Black Screen.
When traveling wind is above Helmet 1 / 3 (Intake) I will pass through. When turning to the side, wind sounds that do not exist until now.
Because Mirror is attached to Bracket, vibration increases and it becomes hard to see.
The color of Screen is quite deep, I can not see the wet Asphalt and the night road well. Even if it is slightly diluted ....
I think that the function as Small Bell Screen is satisfied.
View detail
Installation is Large strange, but performance has the merit of not doing its hardships!
I installed it in Addressv 125.
Commuting is Main, sometimes it is used for Touring of 2 to 300 km.
Mounting first.
As everyone mentioned in Imple, the installation was Large strange on the contrary to the simplicity of the manual.
Address is the Bolt position of Mirror is Quantity : Pair (for Left and Right) I think that it is somewhat different.
There Quantity : Pair (for Left and Right) I attach symmetrical ones, so it's a lot of trouble.
I think that installation can be done in about 1 hour even when working while applying Wax.
Next performance ...
I was surprised to see it running.
3~40km / I confirmed the rectification effect from about h.
60 km on the main road / Travel with h, check the running wind with bare hands.
Although I am 174 cm tall, I was protected by Screen from the lower arm in the state of Riding Position.
Wind protection is available until the shoulder.
I have received decent from the neck up.
60km / H for a moment, there is no shake of Handlebar even after letting go.
And the maximum speed is the same as when not installed yet.
I think that perhaps fuel economy will not change.
And, looks.
Overall, it is just right Size.
With a box of about 30 L behind it.
Strangely Screen does not stand too well, it is not dull.
Even when viewed from the Position of Rider, it does not enter too much for visibility and it feels just right.
Overall, the installation was Large strange but it was a commodity that did not complain anything other than that.
Recommended, honest.
View detail
Making it easy to drive at fast speed. And changing the angle of the wind shield is possible. Very durable and Stylish, and I'm also satisfied with option bar for my smartphone.
Making it easy to drive at fast speed. And changing the angle of the wind shield is possible. Very durable and Stylish, and I'm also satisfied with option bar for my smartphone. View detail