Reviews
Fits: HUSQVARNA TE 510, HUSQVARNA WR 125, HUSQVARNA WR 250, HUSQVARNA WR 300, HUSQVARNA TE 450, HUSQVARNA TC 510, HUSQVARNA TE 250, HUSQVARNA TE 310, HONDA CR 250, HUSQVARNA TC 250, HUSQVARNA TC 310, HUSQVARNA TC 450, HONDA CR 125
Safe to have in stock
I am using it with Enduro, but it is structurally weak because of the original lack of Under Guard.
If it is rolled up, it will break off from the base, and I think it is the same with Manufacture other than Poly sports.
I have now replaced it three times. I have to think of them as consumables,
It would be nice to have a Rubber-shaped Rear Fender from PeLePera.
With Stock in stock, I can replace it even if I break it, so I will try my best to come back and get wound up in a difficult spot!
I also have X-LIGHT from HUSQVARNA, but please note that it cannot be installed because the structure is different in the year.
View detail
OEM same etc.
I bought it because it is a little cheaper than OEM.
The product was installed with no modifications and the quality is good.
View detail
Eurasian bullshit
The answer was that it would arrive in a week or two, but I ended up waiting four weeks. Too much of a wait!
You made me wait too long! You want me to make a difference? You made me wait too long. You made me wait too long. I've been waiting too long.
View detail
It's just a little less accurate.
The advantage of Bolt On is that you can change colors at low cost. Installation is also Bolt On. But the accuracy of the installation is not so good compared to OEM. Especially when you give it to the STAND of the box shape. If you don't have that, it is a perfect product. View detail
OEM Equivalent Product
I bought a used CRF250R with a cracked Rear Fender, so Poly I bought the one made by SPORTS
System or Quantity of mounting holes:Pair (for Left and Right) I was personally satisfied with the product, as there was no distortion of
View detail
Pretty good
I haven't installed it yet, but since I'm a Manufacturer here, it's an accuracy issue The fact that there was no discomfort when it was stacked with the Side cover shows that there is no I would say that the same can be said for the Also, there is no BALI and the texture is good But there is a hole at the position which seems to be a seam of the mold It is located at the bottom of the back end of Seat But it is not so obvious unless you look closely
For these reasons, I can say that it is a good cosmetic product and recommended
In addition, because I am not compatible with the vehicle of another manufacturer, it is naturally Large It needs to be processed What is this guy doing?
View detail
XR250 (MD30) Can also be used
I was looking for Fender to make Rear of XRBAJA a modern day, but none are high.
So, if this product conforming to XR 250 R can be installed, it was very cheap by stepping on and as I tried to buy it, it almost got poned as expected (Al need to shave only nails of Side number) Can be installed with.
Because it is for competition vehicles, machining is necessary for the installation of lights, Wiring, Number (I do not have Sense, though) However, Rear Carrier does not interfere and it is wonderful (* Rough AndRoad's Rear Carrier).
However, as we can see a bit of Sub Frame tips for the previous term, we recommend only to those who do not mind.
View detail
Mounting on DTRACKERX
I installed it in DTRACKERX 2015.
Even if it says that it is installed, processing is necessary.
I really did not like OEM's Rear and wanted to jump up, so I searched for KLX series for the time being and bought it for the time being.
Drill with Drill at the hole position of the OEM tool Case, cut it with the saw while aligning the car body, adjust the height with 6 φ Washer in order to match with the rise of the car body. Then paint.
This product is for KLX, Rear Fender (Inner) It is united. DTRA is a separate body.
Cut according to that side, but this time I hit the Frame near the back of Seat Cut.
As a result, a hole has opened between OEMSide cover and this Fender.
Cut the OEM's Fender and hide it, but also the subtle feelings.
View detail
Rear Fender
It is a Fender for KX 250 but it is attached to the D tiger.
I chose this because I wanted to make it a different Style if the price was cheap.
Of course the shape is quite different, so you must do it without processing.
Cutting and cutting, scraping off the hit place and screw hole, various processing is necessary.
Because the gap between Side cover and Fender is also quite open, we process and paste the Black board into that part.
View detail