Reviews
MODEL Woods HIGH
Used on YZ250FX
Height 180cm
I use it in StandingMain in Course, and I feel that the width, height, and pull of the handlebar are all good for me, and it seems to manage the vibration of the engine very well.
It has been rolled quite a bit, including the lock, but it is only slightly bent and has good durability.
View detail
I thought it was a basic Handlebar.
OEMHandlebar of ktm250tpi is Quantity:Pair (for Left and Right) 1.It was replaced because it was 5cmCut and Handlebar was shaken.
On the difficult course, I could go with a short handlebar, but on the normal MX.EDCourse, when I raised the speed, the handlebar with cut was out of control and I was tired of holding it back.
When I replaced it, the handlebar width was wider and it was easier to control the front swing while driving, making it a little easier to drive.
There is a slight difference in height and pull from the ktmOEMHandlebar, but not much, and after one day of running, I felt no discomfort.
View detail
Handlebar height and strength increased
OEMHandlebar was bent during a fall on a forest road, so it was changed.
The handlebar is thicker, so I also purchased a universal mount kit, which raises the height of the handlebar and makes it easier to stand.
crf250l md47 because it interferes with banjo bolt
The Clamp of the Hand Guard is changed to a Long Type UClamp, and since the length of the Hose from the Master Cylinder is not long enough, it is necessary to remove the Hose from the S-shaped Hook that is guiding the Hose. Also, if you put a Bar pad that fits this, it will be a little troublesome to insert and remove the key. However, considering the strength in terms of performance and ease of standing....
I haven't tipped over since I replaced the handlebar, so I don't know how strong it is.
View detail
More rigid, lighter!
It's more rigid and stable!
That's what I call a Pro taper!
View detail
Used on Honda Grom
We had to replace the entire Handlebar area, so it was a bit of work, but not too difficult.
Taper Handlebar is thicker where it attaches to the Handlebar Post and thinner towards the end.
I replaced the OEM Handlebar with this one because I heard that it bent easily.
Used at Gymkhana. I had a couple of falls, but it didn't freak me out.
View detail
There is an error in the numerical table.
I thought I had purchased the Large size of the pull, pondering while looking at the numerical table of the product Page.
In fact, the C (pull) part was the rise and the E (sweep) was the pull.
The other diagrams in the productPage helped me to understand it correctly.
I was only looking at the numerical table and overlooked it.
I'm honestly bewildered, but it's not a bad product so I'll keep using it.
It would be great if webikeStaff could review this Review and correct any errors.
View detail
Expensive but great!
I've used a variety of Taper Bars, but why? This Handlebar is the most unbending. I don't know why. I've been using it for about 10 years now, even when I crashed in Hoops and broke all my Right ribs. The Handlebar Clamp was bent and this Handlebar did not bend. It is mysterious. If it is a little more cheap, it is the best. By the way, it is NG to use a bent Aluminum Handlebar by modifying it. The Normal bar of Renthal that corrected it while running HoopS is bent. I know of an example of a breakage. View detail
good product
highly quality Handlebar but easy to broken,when I fell down and the Handlebar was bent feeling and now I have to buy one more for ride View detail
Near the NORMALHandle position, vibration has been relieved.
I wanted a handle custom, I was at a loss for about a year.
I really liked the Position of Normal handle and I had previously experienced it becoming hard to get on with Custom.
However, this Handlebar was close to Normal position when Variation of pull width and height were examined a lot..
I bought it to the conclusion that it might make it easier to ride instead if it uses a lot of pulling widths, perhaps without stuffing the Handlebar width.
With the ease of riding as expected, Handlebar vibration at high speeds was reduced. However, it does not become Zero at all.
However, the ease of Position's riding did not disappoint.
I wanted to try evo of Pro taper by all means but it was worthwhile to research and investigate for a year. (Lol)
I wanted to keep the Normal position as small as possible so I wrote Clamp with Y's Gear's OEM Product.
View detail
Good stuff
Even at PROTAPER I tried buying the highest peak, what kind of thing is a bit expensive. 80 km by single cylinder specific vibration / The vibration which came out with about h ceased to be transmitted to the hand. Stiffness feeling, supple one is very excellent. WR is Aluminum's Frame, Thang Arm but Handlebar only Steel, I feel like completing it will be improved by replacing this.
It is really nice..
View detail
Handlebar exchange (Second Repeat
When I was playing with Gymkhana playing on the river bed this time I fell down and the Handlebar was bent feeling so I thought about letting Limit use until it turns slightly but I purchased it as Stock at that time this time.
I exchanged for WyndhamMODEL from OEMHandlebar last time and tried using it for several months
First of all, Position is very natural and easy to ride, running at high pace and trying to protrude Lean Out's Handlebar, etc. I tried something like Uple, but it was easier to knock down as it was easier to knock down, but as I was in tune I could just slip down and Rear Slide Started and it was dangerous if we had not figured the limits firmly (thanks to it a lot I fell down ← I'm bad lucky
When I was Willy I was up and thanks I pushed it, I pushed it up and pulled up was easy and it was good.
In the case of Slide, sit in front and TanTan pack (Two-tiered dropping and half-crash) Even Counter naturally hits but it was not cramped and easy to do.
Quantity by the time this turn : Pair (for Left and Right) Even if it rolls more than 10 times in total, I did not feel a sense of incompatibility when bent, so I wonder if it did well due to rigidity and supple characteristics as well ... and
Perhaps it was bent gradually ... wry smile
We recommend you change from OEM to outside when turning.
However, I think that it will be helpful to some extent.
View detail
Changes from KLX 250
It is my first handlebar exchange with my first off car.
In the OEM bar, Hand guard (Armor Handguardetc. ) Can not be installed, we have purchased this item of sturdy reputation?. MODEL will be HenryLEAD.
When purchasing, it may be necessary to extend the Wire in order to purchase the Mount Kit or change the height of the Handlebar. Incidentally, KLX 250 (08-15) When installing with Clutch lever, it will not enter due to unevenness.
It's about a month to use yet, but the lightening of Handling has increased. A scary scene came out somewhat when driving at high speed, but unpaved road etc etc. Ease of handling is up, we are satisfied with Large change.
View detail
The Renthal and Pro taper which make the two greatest authorities of a Handle community. Since I felt that there was more Renthal in Japan, it was dared to choose the Pro taper. It exchanged with EVO Bar CR HI from the pure Steel handle.
The Renthal and Pro taper which make the two greatest authorities of a Handle community.
Since I felt that there was more Renthal in
Japan, it was dared to choose the Pro taper.
It exchanged with EVO Bar CR HI from the pure Steel handle.
If pure, it is low and treats, and the hot Handling becomes light and becomes easy to carry out a Standing.
With the Magnesium, color also becomes individual and is very pleasing again.
View detail
This Handle is a Handle which was able to improve dramatically. Although the Handle ordinary type [ 22 or 2-mm ] was used, after changing into this Handle recently, arm going up was decreasing sharply and vibration also decreased considerably until now [
This Handle is a Handle which was able to improve dramatically.
Although the Handle ordinary type [ 22 or 2-mm ] was used, after changing into this Handle recently, arm going up was decreasing sharply and vibration also decreased considerably until now [
].
I think that it is durable since it has not yet bent although
rigidity is also highly used and reversed in the Race etc. repeatedly.
It becomes a form where it equips after buying it, since it is useless if you do not buy a Clamp when it attaches this Handle.
It is very a recommended Handle.
View detail