Reviews
Guard rear master cylinder
I bought it to Guard the Rear master cylinder as much as possible.
The design is rugged and can be attached to SEROW without discomfort.
The Edge of the corner was standing up quite a bit, so I chamfered it with File.
We put several sheets of washers over the frame to get a clearance between the frame and the washers, and then attached a rubber board to the gap between the washers and the frame to prevent scratches and to act as a cushioning material.
I was worried that the radius of the Rear brake was quite close, so I shaved it off a little.
View detail
High quality, as expected from ZETA
Motivation
With the purchase of WR250X, I purchased these to prevent the Frame from fading due to rubbing by the Knee grip usually at the ankle.
Was the one you received as per Image?
Emboss processing (ZETALogo) etc., high quality of appearance.
Was the installation difficult?
DIY installation
Some frame guards from overseas cannot be installed unless they are stopped by a large resistor or tie wrap, but this product is bolt-on and has no distortion of the bolt holes.
To install the Guard, simply remove the Yellow and Orange screws and install the Guard.
The area where it meets the frame may rub against it, so I inserted a rubber plate about 2mm thick in the upper portion.
How was your experience with it?
It looks good fitted, but Guard does its job well.
[Included Parts:were they on?
Included Parts other than Body:None
[Was there anything that disappointed you?
None in particular
This time, I was able to buy it at a lower price with my accumulated Points, so I felt like I was getting a Large-change deal.
View detail
It was supposed to be scratch prevention...
I purchased this product to prevent scratches caused by off-road boots on my wr250rAluminum Frame.
I think this product will prevent scratches caused by Boots.
However, this product itself has no BALI, but the Edge is standing up, so if I installed it directly, the Frame would be scratched by this product. I hurriedly bought SpongeSeal at a nearby Home center and attached it to the back of the frame.
The thickness of the SpongeSeal used is 5mm, for reference.
Other than that, no complaints!
The Frame of R is Silver, so it is not noticeable, which is good.
I don't know if X is necessary since it is MOTARD to begin with, but I think it will stand out since it is FrameBlack. I think there are different tastes here.
View detail
Guard the Frame and keep the color from fading!
[How is it used?
It is used with SEROW250, and it is heavily used in the forest road search and the gully Attacketc.
It can be used for XG250 TRICKER.
Was the one you received as per Image?
The shape and details are well finished and as per Image.
Was the installation difficult?
OEM Cover (One SideScrewQuantity):(2pc) Just remove and replace! It's a super easy tan task that even I can do.
How was your experience with it?
To be honest, the SEROW250 & XG250 TRICKER has a Cover even on OEM, so as a Merit of this product.
1.RBrake Side's Master Cylinder can also Guard
2.We can cover a little bit more area than OEM Product, so we can guard more area than OEM Product.
It's a degree.
[Included Parts:were they on?
Four nameplates for installation are included in the package.
Were there any disappointments?
The only color available is Aluminum Ground, so it stands out on BlackFrame vehicles in both good and bad ways.
I put a thick Carbon StyleSticker to muddy the Brown.
0Other items that may be useful include
Point and hang of installation
There is no hang and nothing to worry about because it is just installed directly where the OEM Product Cover was removed.
[With or without Instruction Manual
There was an illustrated booklet in the box, but you don't need it to understand the replacement parts.
[Easy to understand]
The parts are difficult to understand for those who are not interested.
In my experience, the master cylinder of the rear brake has never been damaged in a fall, so it has become a fashion sense, but in a sense, it is a product that I hope will remain a fashion purpose forever.
[Notes]
Not particularly
[ITEMS TO BUY TOGETHER
There is nothing special about this either.
[Opinions and requests to Manufacturer
If possible, please provide Color variations such as Black and Titaniumium color.
View detail
CRF250RALLY 2021 Non-conforming
ZETA Zeta Frame guard
Item Number:ZE52-0019
■Type:Material:5000 Series Aluminum Alloy
Remarks.
Please note:This product is not compatible with your vehicle.
View detail
If you want to do a standing
Grip feeling when standing is considerably improved.
Exclusive Design allows you to remove some of the OEM parts and install it as is with Bolt On.
The important Guard performance is unknown as it will be field tested, but it will probably perform as expected.
View detail
Mounted for frame protection
I installed it to protect the Frame from being scraped by OffBoots.
The build is made of thin aluminum, so it is unlikely to be able to withstand large impacts.
I thought it would be enough to prevent scratches from rubbing with Boots.
If you don't mind the scrapes, you don't need them.
View detail
zeta frame guard [ZE52-0215]
may i used the zeta frame guard on my drz400sm. this frame covers are large and light weight and perfect fitted in the frame, this item manufacturer design are looking smart and very strong aluminum material. this frame guard very easy to install. i will recommend. View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
Cover range is good for a wide range. Installation requires some creativity.
I used to use Z-CARBON Frame guard (item number:ZC35-5115), but the cover range was too narrow, so I changed to this product.
important item
[Was there anything that disappointed you?
Right Side Cover can be fixed at 4 points by Bolt, so it can be installed firmly, but Left Side cannot be fixed firmly because only one point is Bolt fixed. I added Tie Wrap and fixed the lower part of Cover.
Do you have any wishes or improvements you would like to make for the Manufacturer?
The method of fixing Left SideCover should be more creative. And I want you to attach the protective seat to the CoverReverse side of the part that might touch the Frame.
[Do you have any products to compare it to?
Z-CARBON Frame guard (Item # ZC35-5115)
Frequently Asked Items
What made you decide to buy?
Because the coverage range is wider and the price is cheaper than Z-CARBON Frame guard (item number:ZC35-5115).
How was your experience with it?
The frame covers a wide area, so you can cover a large area of contact with off-road boots.
Was the installation difficult?
The Right Side cover is originally It is mountable to the bolt, but since my motorcycle has a modified rear master cylinder, I added an extra clearance at the contact point. I used Tie Wrap of the size that fits into the groove under the Cover and fixed it to the Frame. Now the wobbling was solved.
【Please tell me the installation point and hang】
As it is, there are several parts where the Frame and Cover come into contact with each other, so I bent the Cover slowly by hand so that it does not come into contact with the Frame, and furthermore, I put a thin Urethane sheet on the reverse side of the Cover to avoid the contact with the Frame.
[Was the Instruction Manual easy to understand?
Only a very simple Instruction Manual is included, so you'll need to be creative in your installation.
[Included Parts:were they on?
4 Bolts for the Right Side Cover, and Quantity of Bolts and Nut for the Left Side Cover:1 Set。
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
Installation accuracy
As per the other imprints, the installation accuracy was not so good
Because the gap between the Frame and the Guard is large, put a rubber sheet in between I buried it
The Guard itself is processed by Hairline to prevent scratches from being visible
Other than the installation accuracy, I'm generally satisfied
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
He was very active recently
It's the one I installed in the shop when I bought the bike
Boots, etc. will not damage the Frame and will increase the ease of operation, but
When I took it off after 10 months, the edge of the Guard hit the Frame and the paint peeled off
I don't mind because it's out of sight, but when I recently replaced the Footpeg
This product prevents interference with the Frame, which is a unique problem
It's a true moment of success
I'm going to change the color with paint for aluminum because it doesn't match the color of the frame It is
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
Poor balance between price and quality
The Frame started to get scratches on the Frame, so I bought it, and the TRAILfor Vehicle ones are not so much I didn't have one, so I went with a zeta product
It's just Hairline processing on a plate of aluminum It will be full of Wound soon
There is no problem in the accuracy of the installation & rarr; hole position etc., but if you install it as it is, you will have no problem
There is a point where it hits the Frame, but it might wound the Frame I pasted the thin rubber sheet to the strongest place with double-sided tape other (esp. people) 。
Because you can fix the Frame firmly with OffBoots, you can use Tan DIN
It's easier to ride with a gu
Because of the large gap between the frame and the guard, it is easy to catch branches, etc. on the forest road, so the course I think that soil tends to accumulate in the I think that I will put Sponge etc. in between
It looks like they have carbon and plastic ones, but the fixation was Tie Wrap
I bought this product because I thought it would be damaged by a fall, but it doesn't feel very solid Mm.... hand Gulp And I can bend it just by doing it. lol
Originally, because it is a product for the prevention of Wound, I do not care about Wound etc. in use, but the price If the product is expensive, then it has to be of a reasonable quality and look, or it's not a satisfactory product I would have appreciated it if it was a little cheaper, lol
View detail
Because YsGEAR's Frame guard was unpopular
I saw a comment saying that the Frame guard of YsGEAR is deformed easily like the Le Pera like this title.
There is no worry about Guard by making solid thing itself ? ? ? Is w
Although other people have also written, it is highly likely that the frame will be scratched if mounted without thinking as it is.
I am preparing RubberPlate on the contact surface to prevent scratches.
WR250R dared to make it because Frame is Silver.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
The installation system is bad
It seemed that the position of the Screw hole was slightly misaligned as other people were reviewed..
Some sharpen etc.. I think that it will be necessary to devise such ingenuity.
Protection performance is unknown, but Knee grip may become easier.
Would not it be better to purchase it as Dress-upItems?.
View detail
Hold property rises, it is easy to control.
Because the car body is rounded slightly at NORMAL, the feeling of Hold is not bad for Off-road boots, but by attaching this Frame guard, the Hold property rises markedly.
In my riding method, footpeg and Step plate are important parts for Machine control, it is a foot belly, Heel and ankle, and it holds at various foot parts, but Frame guard is By attaching, the thickness also increased slightly, the area to be Hold increased, making it very easy to control. Although it is Standing, it is easy to get on because it has a solid feeling of Hold during Jump.
Installation method, but the installation manual was not enclosed.
I could judge by Pitch of Bolt hole of product so there was no problem but I think that Manual should be attached.
Body Right Side Quantity Heol Guard's Bolt : Remove 2 pc, add the attached Bolt to Quantity : Just tighten 2 pc.
Left Side removes the Drive sprocket cover, removes the Bolt of the Sub Frame, inserts it obliquely from the Driven Sprocket side, and tightens the Bolt of the Sub Frame. Tightening Torque, like OEM, 2. 7N - I closed with m. I think that it should be written for those who do not have a service manual in Manufacturer.
For me, rather than Frame guard, the meaning of the Step plate is Large.
As the sense of unity with Motorcycle increases, operability improves so it was perfect for me who is an off-road beginner. It is especially recommended for people who want a sense of unity with the body when the car body runs ramping when you run off-road, or those who are suffering from Control.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D tracker, KAWASAKI D Tracker X
The purpose can be fulfilled but the accuracy is bad
I do not have any particular points (Lol) The purpose is achieved.
Bad point is bad accuracy. First of all, Screw holes do not fit and some cutting is necessary
As soon as Screw head does not fit in Body, we exchanged with Small Head Screw.
And the angle of the bent part does not match. Although it is necessary to adjust the angle with actual spot
You will need something like a vise to do for Beauty.
Also, to improve the processability at the manufacturing stage originally, Slit is lightly included in the folding line.
If you adjust it many times it will be politely broken with Gold genus exhaustion.
Although it does not do almost any surface treatment, it is more than the company's Skid plate
Considering that it is a place to rub it, I'm getting slippery.
Is not it better if the texture after consumption is cool?
Since there is only Frame guard for KLX and Carbon,
Although it is not as Designful, purchase for the purpose of protecting Frame.
Since Carbon 's MODEL has replaced Rear master to Yankaha' s Tank integral type than Gold 's face value, I can not expect it, I thought that Aluminum that can process was better and stopped.
In addition, we are also assuming that we will make one-off in the future, so we are considering it as a starting point for that.
View detail
There are also other models
I inquired and purchased for RMX 250 S. There are also other types of cars so please put them up soon.
It is an Anodized item of satin finish. If possible, Color Anodized Aluminum such as Gun meta was good - - -
Because satin silver, soiling etc. are very conspicuous. There is no Clear paint on the surface.
There is also a place not along Frame Curve and you need to fix it.
It is considerably impossible for the price. Now it is difficult to purchase custom parts with out of print cars so it was not satisfactory although I purchased it without any choice.
I am also using Z - CARBON, but there are considerable differences in the result.
However, it is a pleasure to revive the outdated car Parts. Manufacturer's enthusiasm for ☆ 4. But Y'SGEAR like LePeraAluminum board is not a plate, there is a reasonable thickness so strength is no problem. Practicality is high, so it is Recommendation for those who place more emphasis on functions than it looks.
View detail