To use Point

I recently used it in a Tire replacement.
I was A little inquisitive as to whether this was the right way to use it. View detail

Purchased due to the appeal of the cosmetics.

First-class products are always better, but I thought that a measuring instrument of this price would be sufficient. It is more reliable than no management. There are many comparison videos on Youtube, and I found them to be very helpful. If you want to be absolutely particular about tools and equipment, I recommend you to buy a first-class product from the beginning because you will lose money by buying a cheap one. View detail

Overall, KO!!!!

I am satisfied with the well made product, but I have old eyes and it is hard for me to see the memory.
Otherwise, it is OK. View detail

Not bad, but,

Not bad, but the lock part is sometimes subtle and difficult to use. View detail

Introduction to Torque wrench

I can use it for daily maintenance without any problem. The price is reasonable. The long handle makes it easy to apply force and easy to use. View detail

sufficient for one's needs

I bought this for Stem Nut and Wheel nut of my car.
The Torque wrench is a fairly inexpensive part of the Torque wrench, but it is not excessive or inadequate. View detail

Reasonable

This is used for areas where the Torque is Large. Measurement is also possible.
Very easy to use. View detail

Easy

I bought a Torque wrench because I didn't have one before.
Recently, I had more and more chances to tighten the Rear Axle Nut for chain tension adjustment, etc. I did not know how tight I should tighten it, so I just did it by my own roughness.
However, this is safe because it can be tightened at a predetermined Torque.
However, the body is a little large and heavy, so it is not suitable for tightening small parts. View detail

Conversely, Screw is easy to loosen because it is long.

I am not sure if the Torque is accurate or not. I am a little worried about that because it is made in Taiwan...but there is one great advantage.
It is bigger, heavier, and longer than other Torque wrenchs, but fortunately it can easily loosen even the tightest Screw.
If there is a bolt that is too tight, this will loosen it easily, won't it? View detail

Fairly easy to use

I purchased this product to use when changing Tire.
It was just the right length, and I personally liked it just fine. View detail

Large Scale

I purchased this for Torque management of Axle Shaft installation.
The wide range of the Torque measurement range could be used for Caliper Mounting Bolt.
The most Large is 210 Nm, so it is indeed Large-sized. View detail

good

It is large and can be used for changing tires on cars. It is not suitable for engine work. View detail

Cospar good

The content of the instruction manual of the attachment was difficult to understand, but I was able to understand it by the explanation written in the box. I think that the cost is good. View detail

It might be too large for me.

I always ignore Torque when I install Parts and I was worried about it.

But for a cheap price, Case is solid.
I thought that the time to use it would come sooner or later. View detail

Basically, I use it to remove Diamond from Car.

It is 28N-m, so less than 3kg, and Torque is the smallest value around here.
Familiar ones are like Oil's Drain bolt.
This area is OK, but delicate bolts such as Cylinder head cannot be managed.

Because it is assumed to tighten a big Bolt or Nut from the attached Socket and the Size of Socket.
Wheel of the car, it is good for the last Check. View detail

It's good.

Orthodox pre-set type, easy to use, up to 200N type, big and heavy, but well made. The only difference is the Torque value, Quantity:Set is a little difficult to get used to. Because the basic tick value is flying a lot, the tick value Plus12Memory is a little tired. (Lol)
But it can be used for cars, and because it is big and has a long arm, it can do 120N with little force. View detail

Yoshi Yoshi

Used for Z900rsChain adjustment, tightened at 110kn. View detail

It's a pretty big deal

Replacement for Summer Tire on Four Wheels (112N) and Axle Nut in Motorcycle (98N) Used to tighten the
The length is 480mm in the case.
The body alone is 460mm in length and weight, good for use around 100N, easy to set the torque and has a click sound, easy to use, but you may want to have a shorter one for low torque in tight spaces. View detail

Bought it to keep at home.

I basically do the simple maintenance myself, but I've always had a hunch about tightening the Bolts, etc.
I've been able to get by so far, but I thought it would be nice to have one, so I bought it.
The Size is quite Large-textured as it can be used for cars as well.
When using it on a Motorcycle, it's hard to use it in some places. It's like. View detail

In the meantime, if you want a Torque wrench, I recommend it.

In the meantime, if you want a large torque wrench, I can recommend it.
However, I think the accuracy of this product is not so good as an object, and when you turn the Grip part, it feels a bit gory and difficult to turn it.
The key is that the Torque has no large difference between your handheld and the Tonichi, so I think it's a good costumer because you can trust it.

Torque accuracy is fine, but it's not very accurate as a thing.
If you don't mind, I recommend it. View detail