Reviews
For Smartphone Holder installation.
CB250R Handlebar was replaced and the aperture angle became too tight.
Smartphone Holder on Handlebar
I introduced it because it turns inward quite a bit.
Clamp Bar length is 90mm (excluding Cap)
The height is from the Center of the Pipe to the Mirror mounting point.
It is about 50mm to the top edge of the bracket.
The bar length is 10mm shorter than that of HURRICANE.
I was looking for something short, so it is Exactly for me.
Bracket is turned upside down from de Fault.
It's a matter of feeling, but if you put it in this position with the Defferential Gearo
The bracket risers will be exposed to the wind.
Both top and bottom are drilled for M10.
Also, the Cap on the bar is loose, so I used Cellophane tape.
It is tight and inserted.
If you don't do this, the Level will fall down due to vibration.
Smartphone Holder was installed on Best position.
View detail
For cell phones and recharging.
Product Name
Multi Bar
Item Number
EI533EX4A1
Vehicles
NINJA400 (2BL-EX400G)
Number of man-hours
About 10 minutes
Required Tools
Torque wrench, hexagonal socket
Why did you choose this product?
I decided to buy this because I need it to charge my cell phone and cell phone when I ride my Motorcycle. I use Ram Mount and DAYTONA Charger, so I chose this one because it was the cheapest Multi Bar.
Was the one you received as per Image?
It was just like the Image, it came with Screws, Body and Instruction Manual.
Was the installation difficult?
It was easy to remove the two Screws and screw the Body back on again.
How was your experience with it?
The black paint is perfect with no gaps or misaligned screw holes due to the Exclusive Design. I installed Sugar Socket, USB, and Ram Mount, but there is still enough width to mount a gopro or other device.
[Included Parts:were they on?
Instruction Manual, screws, and Body were all available.
[Was there anything that disappointed you?
Nothing in particular. I would be happy if the price was a little lower.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
As if it were an OEM product.
FORZA required the installation of a Multi Bar because the Handlebar was not exposed.
Initially, we attempted to add an inexpensive Universal-type Multi Bar that would be installed using the Mirror hole.
However, when the Handlebar was turned off, it came in contact with the Screenetc. and was not oriented properly, so we decided to purchase this product.
This product is Exclusive Design and does not violate the design of MotorcycleBody, thus satisfying the Large change.
The price is a bit high, but overall I am satisfied with the Large change.
IMPRESSION DETAILS
0Package
Very careful packaging with SpongeCushion as well.
0 Product quality
No welding or processing problems
Good paint job.
0 Installation
Easy even for amateurs without any problems
◯ Usability
It is good that the location study seems to be well done.
I personally think it's a good position, out of the way.
Processing of 0Cover
Endurance sells a special modified Cover, but I have modified the Body.
The instruction manual includes instructions for processing the body (size of the notch is indicated, etc.), and processing is possible using a nipper, cutter, and sandpaper.
I think it's better to start out small and then cut around the edges.
Because it was cut by Nipper, there is a white mark on the CoverBody, but it is not noticeable and I don't mind it.
Related to 0OthersCustom
ETCAntennas are installed in the Handlebar Center Cover with no problems.
Wiring with DAYTONAUSBCable and ETCAntennasCable attached to Multi Bar.
The product was installed by drilling a hole in the MotorcycleBody (plastic), which is not too difficult to process.
In this case, we took care to drill the smallest possible hole, as drilling too large a hole can cause strength problems.
Recommended Point
The large size and length of the bar is the smallest necessary, and it is a functional product that does not destroy the design of FORZABody.
View detail
Looks rigid.
We hesitated with DAYTONA, but chose this one, which looks rigid.
If the Smartphone Holder is attached to the bottom, it is too far forward, and if it is attached to the front, the Meter is not visible.
I am thinking of extending this and attaching a Bar Holder to it to make it an easy-to-see Position.
View detail
late delivery
Delivery date is 3 days later than when the order was placed.
There is also no CanCell button listed in the Cancellation method.
I will never buy from this Site again.
View detail
Patchy
It is cheaper than KIJIMA's product Multi Bar and seems to be convenient, so I purchased it here.
It is good to use and it is easy to use again.
Cigar & USB, Camera pedestal, Smartphone Holder is attached so it is enough.
View detail