Reviews
I like this more than OEM crash bar.
The engine guards are very nicely package and shipped to USA with no problems. There is very good craftsmanship on the welds and design. It is easy to install and looks great! View detail
It takes quite a bit of time and effort to install.
[How is it used?
I don't intend to ??I thought it would be cooler if it was attached, so I installed it although Motorcycle is used.
Was the one you received as per Image?
I was going to buy it on ?Webike, but I found a new one for a little less on Yahoo Auctions, so I bought it there.
?It seems quite sturdy.
?Image was different after the last completion.
Was the installation difficult?
?Engine hanger bolt is to be removed, "Put a Jack under the Engine…" I was worried about that because it was written in the form of a "I'm sorry, I'm sorry. What if the DAYTONA bolt doesn't fit as soon as I remove the bolt from each One Side? I was worried because I am an amateur. (I supported the engine from below with a Jack, but it was hard to do because of the …Exhaust System).
?It may seem like nothing once you get used to it, but it's the first and last time in your life, and you are nervous about this and that.
?I also wasn't sure what Bolt's Torque adjustment was like.
How was your experience with it?
?It looks good when the installation is finished.
? Just think of it as normal. "Daytona" There are plastic parts that give the impression of Quantity:Pair (for Left and Right) I was surprised that I couldn't put them on the same place with both of them. Most of the product photos only show the Right Side of the Motorcycle, but the Left Side has a different Plastic location. If I had known that, I would have bought a cheaper OEM.
[Included Parts:were they on?
? Of course, if you buy it new, it comes with everything.
[Was there anything that disappointed you?
? "Daytona" The position of the plastic parts in the Quantity:Pair (for Left and Right) To be different in the
?KIJIMA and OEM are much cheaper, so from a cosmetic point of view, they may be better.
(DAYTONA is the most Quantity in the form of Guard.:Pair (for Left and Right) I read in word of mouth that they are close to symmetrical … or something like that, so I chose Daytona even though they are more expensive. I feel like I put too much of a good thing on it, even though you're installing it on a used car.)
■Points of installation and hang
?Bolt removal is quite hard, so be careful not to lick the bolt screws.
Availability and clarity of Instruction Manual
?That part is fairly straightforward.
Notes
Since there is no ?20-40 Torque wrench, it is difficult to determine how much to tighten.
Items to buy together
?It is difficult to install without a solid tool.
Opinions and requests to ■Manufacturer
?Quantity:Pair (for Left and Right) Same location "Daytona" The design should be such that the plastic parts of the
? Something is wrong.
?Included Parts:It's great to be able to buy only ?Included Parts:.
?Bolt and Nut should be Black like OEM.
? KIJIMA, I think the price is too high compared to HondaOEM.
View detail
As Described
I have already received the items yesterday (Monday) from local DHL. I planned to ask the local dealer to install it for me this week. View detail
Strong and durable guard bar
My motorcycle is HONDA CB400SF. I bought this bumper to support the car body when the car body falls down slightly, so as to reduce damage to the engine and the car body. Moreover, this bumper is equipped with rubber pads to reduce the damage to the car body. The damage to the frame caused by the installation is small, the screw hole design is reasonable, and the installation is simple and worth buying. -------------------------------------------------- -------- My motorcycle is HONDA CB400SF. It is to buy this barrier to support the car body with a barrier to reduce the damage to the engine and car body when it falls slightly. Smaller installation is damaged to the frame , the screw hole is reasonable, and the installation is simple and worth buying. Powered by Google Translator View detail
The strength seems to be sufficient.
Tanks and Engines do not seem to be damaged when they are knocked down.
Just Quantity:Pair (for Left and Right) The output of the Quantity:Pair (for Left and Right) I was slightly concerned that it was not symmetrical.
View detail
Fits: HONDA CB1300SUPER FOUR SP, HONDA CB1300SF, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SB
Pipe before you fall
'23 I installed it on a CB1300SB SP.
The Single Item shows that it is just a pipe bent and a plate welded to it for mounting, and although it has only two fixing points on the One Side, it seems to be solid.
When installed, the Front side is co-tightened to the Engine MountPoint, and the Rear side is secured to the Frame via a bush, which feels solid.
Although the frame is very compact, it is likely to receive force from the frame in the direction of input that would be applied in a fall from a standstill to a low-speed fall, such as a standing fall, so even with only two fixed points, there is no sense of insecurity.
I felt that the Compact design and the Matte Black color would have a small negative impact on the original design.
I also think it could be used as a mounting point for the trendy ActionCam and other applications.
It would be desirable to end up with a falling-back plan, but I felt that it would minimize the damage if something were to happen.
View detail
Fits: HONDA NC700S, HONDA NC700X, HONDA NC750S, HONDA NC700X, HONDA NC750X, HONDA NC750X TypeLD
Sturdy and surprisingly inconspicuous
Looks surprisingly unobtrusive and Parenthesis is good. View detail
About DAYTONAE Engine Guard
I was torn between products from various manufacturers for the Engine Guard, but DAYTONA's Engine Guard was just the right size, not too large and not too small. 。 A couple of days after installation, I had a bump when I stopped and fell over, but thanks to the Engine Guard, the Handlebar, Clutch lever, Mirror, etc. were not damaged and the Large change was saved!
The rigidity is probably quite good.
View detail
Fits: YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07
DAYTONAEngine Guard
I had it installed when I took delivery of the car, so I don't have a review of the installation process, but it should probably go on easily.
I put it on thinking it was just until I got used to the vehicle, as recommended by Motorcycle Shop, but I hardly feel any discomfort. (Personally.) The "I" is attached as it is because it is a "I".
After all, it took me a few months to get used to the vehicle, and a few times with the typical Pattern of standing staggering, but the effect is quite high.
The similar handling of the vehicle's Frame and the color Black seem to contribute to its inconspicuousness.
Also, there are plastic parts at the contact points in the event of a fall, which can be replaced in the event of severe damage.
In the event of an actual fall, the Handlebar tip and the Exhaust Coveretc. will make contact and cause some scratches, but there will be no Damage to the Parts themselves. It is not as protective as the Bumper on a learner's car, but it is not as noticeable, so it is recommended at least for this vehicle.
View detail
Highway bar dual use
The car is a 2021 BOLT Shoulder Bag R spec ABS.
I thought that a large engine guard would not fit the Bolt, so I chose a small one made by DAYTONA. 。 The OEMAccessories Y'SGEAR is similar in size, but the front part is fixed to the frame, while this product is fastened to the long bolt for the engine mount, so the horizontal part of the pipe is a few centimeters closer to the frame than the one of Y'SGEAR. The horizontal part of the pipe is a few centimeters in front of the Y'SGEAR, and I chose DAYTONA because I thought it would be a good substitute for the highway peg. 。 In fact, it turned out to be the perfect highway peg for me, who is 174cm tall and has short legs.
I deducted a star because the part where the left side is tightened to the engine mount did not fit. 。 The Right Side was a perfect fit, but the Left Side had a gap, so I put two washers and a spring washer on it. The Right Side was just right, but the Left Side had a gap. 。 If it had been a Spacer with the same thickness as the Right, it would have been a just fit.
To install the footpeg, you will need to remove the entire base, and for the left side, you will need to remove the entire stand. If you are going to do the work yourself, you will need to figure out a way to support the car body without the footpeg before you start. 。 I piled up square lumber under the Step base on the Right and used it as a STAND, but I don't think it was stable, so I don't recommend it.
View detail
Z900rs 2021 Pipe Guard
It's classic and fits perfectly.
Sliders are included at the bottom of both sides, so satisfaction is high after installation.
Welding and painting quality is good, and delivery can be received quickly if weekends are not included.
It's not awkward with the black engine, and the paint is semi-gloss. ------------------------------------------------------------ -------- Classic and correctly fit.
The slider is enclosed together on both sides and the satisfaction is high after mounting.
The welding and coating quality are good, and shipping can also be quickly accepted if the weekend is not interrupted.
It is not awkward for a black engine, and the paint is a semi light.
View detail
MT-07 2014 with Daytona Crashbars
It looks similar to training school but more low in profile. how effective it is in guarding the engine, I do not know and can only hope for the best View detail
Fits: YAMAHA MT-09, YAMAHA XSR900, YAMAHA MT-09 To Racer, YAMAHA MT-09
When Bolt and Nut
I had installed Y's Gear's Slider, but I also installed Engine Guard.
The Bolt and Nut were Zinc Plating, so I replaced the Nut and Washer with Black ones.
View detail
Fits: YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07
If you're just standing there, it works!
Originally the Horn (Quantity) of BOSCH:I bought this as a Bracket to install my FOGLight (installed with Pair) and FOGLight (not installed).
As for the installation itself, I was able to install it Firmly without any problem of accuracy, but I did not dare to install the resin Cover because there was no space with the above equipment.
By the way, the other day, in the middle of touring, I stalled the car at the start, which is common to MT-07, but I only got a little scratch on the tip of Knuckle guard and Mirror.
The only thing I didn't expect was that the Knee SliderPin of the Left Sidefootpeg was ripped off because I fell down on a steep uphill to the main road with the Handlebar turned all the way to Left.
In any case, it will be effective enough for the damage of Brake & Clutch lever and Radiator and the dent of Tank.
View detail
z900RSPipe Engine Guard installation
Installed to reduce damaging effects of standing and falling.
It looks like a car school instructional vehicle after it's installed.
The Matte Black paint job is surprisingly unobtrusive.
Installation is easy if you follow the Instruction Manual.
View detail
Fits: YAMAHA MT-09, YAMAHA XSR900, YAMAHA MT-09 To Racer, YAMAHA MT-09
It's not so much for falling down, but to prevent damage during standing and groping.
Installation was relatively easy. However, the maintenance stand and the support for the Engine (Automotive Jacketc.) is better to have.
Style-wise, it doesn't stick out weirdly and I like it.
It has been six months since I installed it and I am happy with it, it does not interfere with my Pedal operation.
View detail
Nice and inconspicuous.
It was discreet and I liked it and bought and installed it.
As expected of DAYTONA.
Mounting accuracy is high.
Others have commented that the Front tire floats, but I don't want to have to deal with this product in a fall.
View detail
Fits: YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07, YAMAHA MT-07
Just in case.
I purchased and installed it to protect it in case it falls over. It's easy to install. It is easy to install.:Depending on the position of the plastic protector, this may reduce the damage to the Pipe area. View detail
Very good
I installed it myself in 30 mins with the bike on the side stand. Easy to install and quite beautiful on the bike, in my opinion. Also useful in case you drop the bike. View detail
Malaysia
if order and sent to malaysia .. once it has arrived check with custom (kastam). It will take them a bit of time to get to you so call them and check with them Item arrived and Im satisfy . View detail