Reviews
Fits: KAWASAKI ZX-6R, KAWASAKI ZRX1200DAEG, KAWASAKI Z250, KAWASAKI Z1000 (water-cooled), KAWASAKI Ninja400R, KAWASAKI Ninja250, KAWASAKI Ninja1000
For your first Custom! Made in Taiwan! No visibility problems!
There is no difference between this product and the OEM Product except for the color. I did not feel any impression of poor workmanship.
The Blinker's visibility is not reduced during the daytime, and it successfully combines practicality and good looks!
View detail
Fits: KAWASAKI Zephyr χ, KAWASAKI Zephyr 750 RS, KAWASAKI Zephyr 750, KAWASAKI Zephyr 110, KAWASAKI Zephyr 110 RS, KAWASAKI ZRXII, KAWASAKI Zephyr 400
That's not the picture
It looks shiny in the photo, but the actual product is dull. View detail
Fits: KAWASAKI GPZ750 R, KAWASAKI GPZ900 R, KAWASAKI ZR-7, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI GPZ750 R, KAWASAKI GPZ900 R, KAWASAKI ZR-7, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
good
Used on the ZrX1100's rear blinker Before installing this product, the front blinker has a front blinker made by POSH [Color] Installed a SmokeBlinker
FrontPOSH and Rear is a mismatched spec. called Jills, but the quality of both are It was finished without any discomfort due to its solidity
The only thing that bothered me was that there was a lot of BALI left on the product, so I had to tighten the screw as it was Sometimes it didn't close tightly enough and had to be sanded down
The POSH product could be installed without such a thing
View detail
The side BALI is Spec. is.
I was disappointed..
About 5 mm of BALI remained on the side of Blinker lens.
1pc. Not only 4 were in this state.
Although there is no complaint if it is a part that can not be seen after installation,
It is remarkable because it remains on the surface.
When I contact Manufacturer, this is Product Spec. apparently.
If it is Clear Lens it may not be noticeable so far,
It's quite outstanding because of the Smoked lens.
I think that it is better not to buy it except absolutely those who can handle to Beauty.
View detail
Fits: KAWASAKI GPZ750 R, KAWASAKI GPZ900 R, KAWASAKI ZR-7, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI GPZ750 R, KAWASAKI GPZ900 R, KAWASAKI ZR-7, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Excellent compatibility with SmokeTail
I also exchanged this as Tail was made Smoke
Although it was not in the explanation, Amber 's Valve was also attached
However, both are double valves ...
Font Blinker is Double Bulb and it can be used because it becomes Position with Key ON ...
Rear is a poor position and angle in the mouth Gold Poses are different, so you can not use it as it is
For the time being, if it feels like Pin 1 pc. Once you scrape or drop it with Nipper, you can use it once.
Double Bulb has 2 contacts of Valve, but the TailBlinker part has only one point of contact, so if it is in contact it will light up when Blinker ...
However, because there is no Pin in one side, it can be said that it swings immediately with the vibration, so if you use Valve, you can get Valve's Home Center and AutoBacks around for Rear to get Amber's Single Bulb I think it's better to keep it.
In my case I replaced both LED Bulb back and forth
Although it is a point of caution at the time of installation, it is a feeling to tighten with a Tapping screw like Tail and dig into a thread, so once it is tightened, once it is tightened, it is sure that you take off the tuna and tighten it again
Since Crack enters or it is broken as you keep tightening up to the end as it is ...
This also has four holes Gap and Woundetc. There was not too good condition.
I am worried about that point if it is overseas cheap, but for GPZ it's a lot so there are few Rose stuffs so I guess ... (Lol)
Although I do not know whether it will be a reference because it is exchanged for LED Bulb, it was also that this time when Position also in the daytime, the brightness at the time of lighting is necessary and enough, the vehicle inspection will be cool
It is good because the price is also cheap and the atmosphere changes at a stretch
Recommendation for exchange with Tail lens
View detail
Fits: HONDA VTR250, HONDA HORNET 250, HONDA JADE 250, HONDA CB-1, HONDA CB400 SF
VTR250
Attached to VTR 250 Carburetor Vehicles. It is a feel free Dress-up because it is just replacing the Lens with the Driver and changing Valve. I purchased Clear Lens, so I need to make it an Orange sphere. Wiring It is unnecessary such as processing, Recommendation for those who want a little Custom.
View detail
Fits: HONDA VTR250, HONDA HORNET 250, HONDA JADE 250, HONDA CB-1, HONDA CB400 SF
Color depth
It was also in Impre of another person, but it feels like it is a bit dense. It is combined with SmokeTail of the same Manufacturer, but there is a color difference, but it is personally acceptable. I feel easy to buy if you get Orange ball. View detail