After some DIY, I managed to get a piece of the action, but

Previously on & omega;
It's too good to throw away, so do-it-yourself measures

The rattling thing is a recessed OEMSTAND 12.4mm wide. This one is 12.5mm wide.
So we ordered Stainless Shim inner diameter 12mm, outer diameter 22mm, and thickness 0.1mm.

Bite into this stuff and it's perfect.
I ordered 0.05mm, 0.02mm and 0.01mm just to be sure, but they're out of stock & omega;
Also, you should definitely have a spring hook.
Even a cheap one is enough for me, so I'll keep it & omega;
It's a full-powered tool and I'm afraid of substitutions.
STANDBolt/Nut is 14mm/14mm
Side stands sensor fixed bolt is 8mm

Too short All Screw, Order M12/P1.75 inch cut Stainless bolt 110mm for extension
The Uniqlo length NutM12/L60 on this one.
I couldn't find a good one around L60 in Stainless Steel length Nut, so I used Uniqlo ω
Also, the M12Stainless Nut 3 different thin 1Pack
The rest of it will be on the rubber board for about 1,000 years. It's a useless cost, but it's unavoidable.

I decided to temporarily connect them with a long nut for 30mm each, and then fill up the all screw of the body with 30-35mm

I used a disk grinder to cut it down to 32mm.
It's adjustable, so just use About.

Then, put two nuts in the bolt for the double nut, put the body cut with a long nut and tighten it up.

Also, the angle of the STAND toe is poor, and it's only grounded on the inside of the STAND only.
So I put it on the Rubber Board Teketo and it's done

Well, I've managed the Large goal of somehow improving my over-sleeping OEMSide Stand.
I'm not happy with some of the details, but it's good because we achieved the minimum objective.

Just not for people who can't do DIY; View detail

Staggeringly desk-bound product

First things first.
Unless you're a pro with some degree of do-it-yourself savvy, there's nothing you can do about it.
If you're looking for a way to stay in place and say, "Hey, turn around!

First of all, I can only assume that whoever made this thing didn't actually use the CT125 CT110 HUNTER CUB.
If you try to ride a little bit, you shouldn't realize that the Side Stand angle is too much for you to sleep on, …………

It's a fatal point of the Uli's Adjust function. The Stainless SteelAll Screw is turned to adjust the length of the side stand, but even if the length is set to Large, it's only the same length as the normal side stand.
It is possible to adjust the side stand which is too much sleep to make it lie down further, or Level which makes you doubt your sanity.
I'd love to hear what they made it adjustable for.

Furthermore, I tried to install it, but the opening of the upper recess on the Side Stand side was too large, so I tentatively assembled it, and it rattled ……………
We're running out of time.

I think that it can be managed by procuring a Washer or Spacer that fills the gap between the rattling, or cutting a hole in the aluminum plate if it is made to be used somehow. hellip;……… …

As for the height, in case you're wondering, STAND's feet are wide and have holes in the four corners.
If I can get a hard rubber board of the height you want to earn and drilled and bolted it up, I can make it work, but …………………

I feel like I've been grabbed by a hell of a HaGap for the first time in a long time.
I think you should have at least a countermeasure Washer in the package ω
If you have any intelligence, you should extend the All Screw section a few more inches now.

I'll report back when I've done the DIY. View detail