Reviews
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Safe if you put it up first.
Once it is applied, it blends in so well that you can't even tell it's there.
It is good for preventing scratches, and if it should get damaged, it may only be a matter of replacing the film.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
Quantity:1 Set of 2pcs. is good
The first one failed.
Apply a large amount of Film Paste Spray to the film and paste it well.
The second one went on well. It's so good that you can't even tell it's on.
View detail
I'm using it attached to the Hunter Curve instrument panel. I am satisfied.
Since the two pieces are in one set, the installation failed due to a small mistake at the time of the first installation, and fortunately, I tried again with a spare and succeeded. I sprayed it with water mixed with a little neutral detergent to thoroughly wash off the dust, etc., and installed it. It can't be helped that it can't block sunlight reflection, so depending on the time and direction, the sunlight is reflected and it's hard to see. -------------------------------------------------- -------- Two copies were included in one set, so when they first installed, they failed to mount due to a small mistake, and fortunately they tried to re-attempt with leisure. Sprinkle with a bit of a mixture of neutral detergent, washed off and installed enough dust. It is inevitable that the sunlight is reflected in time and direction because the reflection of the sun is not prevented, but I liked it to be well protected from the wounds due to the fitting and the small dust. Powered by Google Translator View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
In use for 6 months
If the product is a Quantity:Set of 2pcs. is a good thing. It is easy to fail in attaching.
Many of these days, for smartphones. GlassFilm. The protective film is made of a soft polyester, unlike the
It is difficult to determine the affixing position and Garbage is easy to get into.
Therefore, we recommend that you review the procedure in Review and videos before installation.
I have a lot of AppleWatch Films of this kind, so I have a few failed attempts to affix them and experience
Since it was stacked, I was able to attach it successfully in one go.
My friend failed to paste both sheets and they became Garbage.
Once the product is successfully affixed, it will blend in so well that you will not be able to tell that it has been applied visually.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
I want you to stay clean.
I bought this product because I didn't want my meter to get scratched, so I bought the Instruction Manual, AlcoholPaper for degreasing, Quantity:1 Set of 2pcs., The spatula is enough to remove the bubbles. The CT110 HUNTER CUB Meter Bulb surface is quite difficult to remove the air bubbles. View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
The back side mount Film is not peeled off…
The Film which became the base of Reverse side did not come off easily no matter how carefully and carefully I did. It is not peeled off at first by turning the Seal which is attached. After all, it wakes up with a nail and it becomes a thing to peel off, and the edge of BodyFilm is damaged inevitably.
Also, the CT125 Meter is a curved surface, so the degree of difficulty is quite high, and even if I discount my clumsiness, I couldn't paste it satisfactorily with the Film which damaged the edge. In the end, I threw away both of them because the glue was left when I removed them from the Meter, and I had to damage the Meter to remove it.
We recommend that you leave the work to a shop that knows how to do it, but even a PRO may not be able to remove the mount film well.
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
It's hard to put it on a curved surface...
[How is it used?
daily use
Was the one you received as per Image?
As per Image, 2pcs, thin feeling of Screen Protection Seal for smartphone.
How was your experience with it?
CT110 HUNTER CUB Meter is difficult to paste because of the curved surface, I was not able to remove air bubbles well!
[Points to note]
Difficult to apply, especially to remove air bubbles, I was left with a few bubbles!
View detail
Fits: HONDA CT125, HONDA MONKEY125, HONDA TRAIL125
A product that may work in the medium to long term.
The Meterassy of the CT125 CT110 HUNTER CUB has a convex spherical structure of resin, which is easier to scratch than you think!
So I Ordered this product!
As a matter of fact, it's only after it's scratched that I'm able to remove the scratches at the same time ω
I ordered a low cost headlight polish with Linley solvent, polished it twice, and repeated finishing with Micro fiber, and it recovered a reasonably clean feeling.
From there, as per the Manual, degreasing cleaning> temporary fasteningSeal using three temporary fastening, since there is no mist spray, Self sake splashω
I filled it with water, scraped out the air bubbles with the included spatula, and somehow
I'm glad I didn't make a mistake and fall into the trap of having to use a second one ω
The manual is very helpful, and the work is not so difficult if you follow the steps and do it properly.
I think it's Level for 15 minutes of labor.
The CT110 HUNTER CUB is a digital meter, so it's hard to understand intuitively, so it's important to keep the meter screen visible.
I think it's not a bad idea to use a protective film to prevent scratches before they happen.
View detail