Vibration Isolation Outclassing

A little soft, but firm and very good.
We will make it a good companion for future Touring. View detail

SIGN HOUSE

I don't know as it has only been installed for a short time. View detail

It's not working

I bought it because I was worried about the phone malfunctioning, but it is obviously too soft and I think it shakes a lot while driving.
In my case, I did not install it because it is located close to the tank and it might shake and hit the tank.
It was too expensive to purchase as it was not usable. View detail

More &hellip. than I imagined;

I was hoping that it would be an anti-vibration solution from the 1200ccLTWINEngine, and it must be effective because it was sold out for a while at Motorcycle supply stores. When I actually used it, I felt that the rubber hardness was too soft. I think it would be better to reduce the amount of deformation of the rubber a little more. View detail

Design and quality are good but squishy

I think Vibration is effective, but it is too Kunikunashi and very cumbersome to install and remove the phone. View detail

I bought it to try it out.

I bought it to see what it was like.
I think it had what I needed, I don't remember if Screw lock was included.
Installation is easy and can be done quickly by referring to the Instruction Manual.
I think I have driven about 4000 km using it. At first, I was uncomfortable with the higher position of the phone, it is higher for the thickness of the Rubber part.
The softness makes it difficult to adjust the positioning of the phone. It is also difficult to detach and attach the cell phone. Well, it is a matter of getting used to it.
While driving, you can see that the vibration is mitigated. That said, the screen is not difficult to see.
It is difficult to operate the screen while the Holder is attached. Once you get used to it, it is no problem.
I think the protection of the mobile Camera is working.
It would have been nice if the rubber was a little stiffer. Also, it would have been nice if it could be kept within the length of the Parts before installation. View detail

You can rest assured that there are issues.

Purchased this because I replaced it with an iPhone 13 unbranded. I have never used a Folder from another company, so I can't compare, but personally, it was not as squishy as I expected. I'm not sure if it's because it absorbs vibrations, though. What about the Quad Rock Damper?
I can rest assured, but I think 5,000 yen is a lot of money. View detail

Durability is unknown.

I don't know if it really works, but I guess it does because my iPhone 11 is not broken. There is a wobble in the feel of use, but I don't mind it myself. 2 years is recommended for Parts replacement, but this is a bit short. View detail

I don't think this is the best shape.

Quantity the phone:Set will deflect by its weight. To begin with, the BUnit determines the angle between A and C. The BUnit is used to determine the angle between A and C, and the squishy Unit is used to make it difficult to position the BUnit. I wish it was easier to change the angle. If the angle is close to horizontal, you can operate the phone just fine, but if you angle it, you can't operate the phone as you want. For such an expensive product, the feel of the product was terrible. View detail

Whether it really works is a mystery.

Vibration is mitigated by sandwiching the Rubber plate between the front and back of the three feet.

It tilts under the weight of the phone, so it may be doubtful how much vibration mitigation capability it actually has if it is tilted by a heavy phone.

The Rubber board is said to be a PARTS that needs to be replaced in about 2 years, but given that the Beacom 5X Speaker is disappearing from bulk sales, it is doubtful how long it will be sold individually.
I hope SYGN HOUSE will not try to sell the same parts even if improved products are released in the future, because it is doubtful that they will be made into the same parts.

If the Rubber plate is hardened, it is still OK, but considering the possibility of deterioration such as tearing off, I wanted the front and back to be connected by a wire to prevent falling off.

Since this is a Type product that mitigates rather than suppresses vibration, it is likely that some Motorcycles will have RPMs that increase the amount of vibration that makes it difficult to see the phone as much as it decreases the amount of microvibration that can be fatal to the phone that is not visible to the human eye.

It can be used for the old product, but it is troublesome because the place to fasten it with Screw adhesive has to be removed. View detail