Reviews
I used it with FCR Carburetor Body28.
It is for vm26, but I changed the Spigot and used it with FCR Carburetor Body28.
In the case of CHALY, you need to engage a 6mm Spacer made by GCraft or Minimoto under the Manifold or it will hit the Frame.
As a precaution, the inside of the Manifold should be cleaned well before use.
The Manifold I bought had visible Level chips on the inside.
View detail
The carburetor leans too far forward.
The carburetor is tilted too far forward, the oil level is not stable, and the Rubber is not durable. View detail
Fits: YAMAHA MR50, YAMAHA POCKE, YAMAHA VOGEL, YAMAHA GT50, YAMAHA GR80, YAMAHA GR50, YAMAHA TY80, YAMAHA TY50, YAMAHA RD50, YAMAHA GT80
Products that are often in short supply
This product used to be cast aluminum, but now it is all aluminum billet. (Cut-out) It is
Perhaps this product is not manufactured by FOR JAPAN MODEL, but somewhere overseas. I don't know if it is because of Corona or the war, but it has been completely unavailable for the past few months, and I bought it when the supply finally resumed.
This lot may have been produced at a different factory, and while there are no problems with use, it is somewhat disappointing that the finished surface of the internal flow channel is rougher than before.
I don't think it will affect the performance, but if you are concerned, you can polish it yourself with Leutor's Paper flapetc.
View detail
Perfect and fit for my bike
This product fit my bike perfectly. I have tried with different products from Japan Yahoo but unfortunately they are not fitted my bike. Finally I found this nice one in Webike HK. View detail
Kitaco angle manifold set
I purchased this intake kit to use with a Mikuni VM 26 carburetor on my bike. Ensure you need an angle intafke manifold to clear the frame on your bike. This manifold woorks good, I just wish there wre less pieces. Other than that it works for me. View detail
Kitaco straight intake manifold set
I purchased this intake kit to use with a Mikuni PWK 28 carburetor on my bike. Ensure you need a straight intake manifold to clear the frame on your bike. This manifold works good, I just wish there wre less pieces. Other than that it works for me. View detail
Previously on Carburetor Body and now this Quantity:Let me know if you can or cannot install the set purchase too in the first place!
I'm new to motorcycles and I'm trying to replace the carburetor I'm not sure if I ordered the right one, but I'm not sure if it's the right one I did View detail
Fits: HONDA MONKEY BAJA, HONDA MONKEY BAJA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA XR50R (for competition), HONDA CRF50F
It attached to KITACO Standard-head 88cc of the Webike Monitor MONKEY. Carburetor attachment became a Rubber holder for the change from KEIHIN PCphi20 Carburetor kit, and the Setting became easy. Since the diameter of a port was also
It attached to KITACO Standard-head 88cc of the Webike Monitor
MONKEY.
Carburetor attachment became a Rubber holder for the change from
KEIHIN PCphi20 Carburetor kit, and the Setting became easy.
Since the diameter of a port was also diameter[ of a large ]-ized again, PE24 carburetor was matched and it led also to the remarkable Power up.
View detail
Fits: YAMAHA YSR80, YAMAHA TZ50, YAMAHA TDR80, YAMAHA RZ50, YAMAHA RZ50, YAMAHA TDR50, YAMAHA TZR50, YAMAHA YSR50
Although it was a Manifold set for the Big carburetors of 24 pies of a Mikuni, it was used for PE24 of a KEIHIN. attachment is easy, and if the Manifold currently attached from the first can be removed, it can be attached in a reverse procedure
Although it was a Manifold set for the Big carburetors of 24 pies of a Mikuni, it was used for PE24 of a KEIHIN.
attachment is easy, and if the Manifold currently attached from the first can be removed, it can be attached in a reverse procedure.
Since the
Manifold will deteriorate easily if time passes with the parts of a Rubber, it is dramatically kind if only this part is sold (the product made from a KEIHIN does not have an option).
View detail
It attached to KSR80. Since it is an object for NSR and a fitting hole does not suit, processing is required. Although the object for installation kit KSR of PE24 had come out of Mr. Daytona, since it cannot purchase any longer now, the direction
It attached to KSR80.
Since it is an object for NSR and a fitting hole does not suit, processing is required.
Although the object for installation kit KSR of PE24 had come out of Mr. Daytona, since it cannot purchase any longer now, the direction of PE only has attaching by appropriation.
If a fitting hole is processed, it can attach satisfactorily.
The direction of an idea is recommended in PE carburetor for Ho of KSR in that which also says an angle and sag exactly.
A price is also cheap.
Although it is reference, mikuni VM24, PWK28, etc. have big cab attachment of KSR in others, but they can divert KX65 inlet manifold.
View detail
The manifold for 28 pies did not not much have the amount of handling, and having searched was serious. Although deception is effective, I would like to attach some easily too.
The manifold for 28 pies did not not much have the amount of handling, and having searched was serious.
Although deception is effective, I would like to attach some easily too.
View detail