Reviews
To match intake and exhaust system changes
MJ's position was raised due to the air cleaner element and the exhaust air removal Up. View detail
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
The carburetor leans too far forward.
The carburetor is tilted too far forward, the oil level is not stable, and the Rubber is not durable. View detail
Made by DAYTONA
[How is it used?
Used to replace front and rear Drum Brake Shoe,
Because the previous Shoe replacement time was unknown and it was not working well.
How was your experience with it?
When Brake was applied with the same sensation as before the replacement, the Rear brake worked so well that it locked up!
How did it compare to other products?
It may not be as effective as a disc brake, but it is as good as a disc brake, and I am very satisfied with the large size.
[Points to note]
Nothing in particular, but beveling of the shoe, cleaning of the drum brake, and grease up are also required prior to installation.
Brake wires, clutch wires, and other parts were also replaced, both front and rear, but it was not a difficult job, as it was started in the morning and finished before noon.
(I'm giving it 4 stars because I'm not sure how durable it will be.)
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
Very high CP ◎No accuracy problems
[How is it used?
Installed on a JC75 Grom.
The custom is an external Full Exhaust System, Mukawa N-15 High Camshaft, i-map, and a mid to high speed Emphasis on Torque Light tuneSpec. with air cleaner processing.
At the same time, DID's SUPERNon-seal Chain was installed.
Was the one you received as per Image?
The image is just as I imagined.
Was the installation difficult?
The maintenance stand I bought the other day didn't fit, so I had no choice but to ask the Shop to install it.
How was your experience with it?
The 14T was introduced, 1T lower than the OEM 15T. The Grom's 4-speed Mission is easier to enter the power band when the Final is set to CROSS, and acceleration is lighter with a higher GEAR ratio in 4th gear.
As a Merit, the Torque feeling during acceleration has been improved as intended, and the expected acceleration feeling can be obtained even when climbing hills. Also, the maximum speed on level ground has increased.
As for the Demerit, fuel consumption will deteriorate because of the higher cruising RPM, and the noise and vibration are somewhat annoying when cruising at high speeds. Naturally, the maximum speed is also reduced. In addition, Groms have a speed sensor in the transmission, so the speed meter can be inaccurate. Groms are happy (displayed higher) by about 10%, but they are also unhappy by about another 10%. (e.g. GPS:60km/h Meter before replacement:66km/h Meter after replacement:72km/h)
[Included Parts:were they on?
HolderPlate is included; Bolt is also recommended for replacement but not included.
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If you want to dress-up the Sprocket Cover, you should purchase it first.
View detail
I don't think there's anything wrong with the efficacy at all.
I don't know if it's dull or not, I switched from Metallica and I can't tell the difference. View detail
Cheap and satisfying
It was cheap and easy to install.
I'm happy with it
View detail
Sometimes it is more Large strange to remove an old OEMRubber.
[How is it used?
I purchased this product to do a little dress-up work on a long-abandoned LITTLE CUB after maintenance &restore had been completed.
Side StandRubber was installed in a high percentage of Honda cars in the 1980's and 1990's. Even when the ground was soft at the parking position, it was very useful because it was difficult for the stand to be buried.
The vehicle we acquired this time did not have any deterioration of Side StandRubber, but we changed Footpeg Rubber and Kick Pedal Rubber to Brown as well as Refresh, so Side StandRubber was also changed to Brown.
Did you receive the item as per the Image?
Since they are the same brand, both Footpeg Rubber and Kick Pedal Rubber are Brown, and I am self-satisfied with the color.
Was it difficult to install?
Less difficult, but the old Side StandRubber won't come off!
The mounting part was deformed, and the rubber was firmly wedged in the rubber due to rust, so it took a long time to come off, even though I sprayed oil spray all over it.
After removal, the deformation of the mounting area should be corrected, the rust prevention process should be performed, and then the mounting procedure should be reversed to complete the process.
Older vehicles or vehicles that were ... in storage conditions may have a hard time.
How did you like it?
The functional part of the product is the same as the OEM, and it does a good job of preventing the sinking of STAND.
The number one effect is. They're pretty to look at." It is a modest and unobtrusive part of the project, but it is highly self-satisfying.
Was "Included Parts:" attached?
Side StandRubber1pc. only.
Were there any disappointments?
As I mentioned above, it has the same effect as OEM and looks pretty enough to meet our expectations.
Other items that would be helpful
Point and hang of installation
As mentioned above, for some vehicles, removing the originally installed OEM parts can be a tedious process. 'A simple job to remove OEM Parts and install this product' It is
[Availability and clarity of the Instruction Manual
I don't think there was an Instruction Manual...?
Well, if you are buying this product, you know which Parts to replace, so I don't see any problem.
[Notes]
Depending on the condition of the STAND section of the vehicle, force may be required, so please be careful not to injure yourself.
[ITEMS TO BUY TOGETHER
Footpeg Rubber and Kick Pedal Rubber are also sold by the same KIJIMABrand, so it would be fun to enjoy color coordination.
Whether you want a unified look or dare to use RoseRose's colors, please fully demonstrate the buyer's Sense.
[Opinions and requests to Manufacturer
Please continue to sell the current Color line nap for many years to come.
View detail
long vowel mark (usually only used in katakana) (>ω<;)
Converted to my son's BALIUSA5, which had an air leak from the MASTER.
I thought about installing the Radial master, but I decided to go with the ZrX1200 DAEG because it is expected to be replaced by the ZrX1200 DAEG next year, so I decided to go with this one for cosmetic reasons.
Tank Separated Type is good for a different atmosphere. (? ・ ・?)
For the price, Touch was fine and a good buy!
However, it may be a little long for Mr. Balius in the standard lever….
It was sticking out of the handlebar, so I replaced it with a short lever. (Polish)
I should have measured the length before purchasing and selected the short lever type lol.
View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100
Thanks!
I chose the existing small sprocket while trying to change it by changing the chain. I'm very satisfied because it seems to deliver the speed well. View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Product # 1P2004
One of my friends has a rare YAMAHA Town Mate 6 volt motorcycle. He was faced with the problem of finding incandescent headlamps. We are very lucky that this product is available in the webike. The workmanship is good. Great price. View detail
Fits: YAMAHA Cygnus X SR, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI SV400, SUZUKI RMX250S, SUZUKI RMX250, SUZUKI RG200, SUZUKI GSX250S Katana, SUZUKI GS400E, SUZUKI GS125E Katana, SUZUKI GS125, SUZUKI DR250S
Great!
Replaced an OEM Master Cylinder with a BALIUSA5 that developed an air leak.
The color is Black×Black.
I was relieved to find that the front brake, which does not bite the air, was properly connected to the Snap. (? ・ ・?)
The only problem I have with this vehicle is ….
The tank is placed too close to the HandlebarCenter and may be covered by the Tachometer.
Well, I can just buy a Bracket at Home center and move it to a new location, lol.
I have a shabby blog, if you are interested! (^_^;)
https://enjoy-motorcycle.blog.jp/
View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100
Better looking and performing front drive sprocket then the original Honda part
About quality and texture, I can confirm that the quality is great and that the material used is S45C steel which is a medium carbon steel resulting in a lighter and harder wearing part. About the feeling of use, A better looking and performing drive sprocket then the original Honda part. Products to buy together, The drive chain system on any typical motorcycle is made up of three parts that ideally are replaced together so it would be good practice to also add a rear driven sprocket and drive chain to your cart. Difficulty of installation, I can say the fitment of the drive sprocket for my installation was easy due to the ease of access and simple nature of placing the sprocket into the shaft and securing with the included locking plate. Cost performance and comparison with other products, The pricing of the product is great. You receive a sprocket made from quality and light weight material. There are no cheaper options with the lightweight design that I could find, even the original Honda part is more expensive. About shipping and packaging, My order was shipped within 24 hours of the product being in stock and I received a few emails advising me of the status up until the order was dispatched. The order arrived within the estimated date range and was extremely well packaged. I found the link supplied to track my order very useful while I was waiting for the order to land in the country. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
Fits: SUZUKI GEMMA 125, SUZUKI TS200R, SUZUKI TS125, SUZUKI DF200E, SUZUKI GS125E, SUZUKI STREET MAGIC 110, SUZUKI TS50 HUSTLER, SUZUKI STREET MAGICS, SUZUKI STREET MAGIC, KAWASAKI Z250FT, KAWASAKI KL250R, KAWASAKI KLR250, KAWASAKI KMX200, KAWASAKI Z200, HONDA XRBAJA, KAWASAKI KMX125, HONDA REBEL, HONDA XL250R, HONDA XLR250R, HONDA FTR250
Careful with Size, but if it fits, it's easy!
Used for TW200E
The previous Owner has been playing around with things, so the Headlight is unknown what the OEM one is, but it fits the Limit and was very easy to install.
The head seems to be 20mm longer than the OEM Product, so size confirmation is essential.
View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100
Honda's Mission mopeds are Large body compatible.
[How is it used?
I bought it to refresh the drivetrain which had been neglected for a long time, and to replace it with a Driven Sprocket that was swung to the maximum speed side about 2 guns more than OEM because I replaced it with a 90cc Engine of Tanaka Shokai. I bought it to refresh the drivetrain.
Was the one you received as per Image?
KITACO's Custom parts has been helping me a lot since I got my moped license in the summer when I was 16 years old.
Honda's DriveSprocket for mini bikes is the same as the Large body, so it was a product that I was too familiar with and passed by the Image because I have been using it since I was participating in mini bike races with my NSR50.
Was the installation difficult?
The Driven Sprocket is easier to detach than the Driven (Rear sprocket).
The SprocketBody can be easily removed by removing the Cover, removing the two Bolts holding the Sprocket & Holder, and removing the Holder along with the nails.
When installing, the reverse of the above procedure is used to complete the assembly.
How was your experience with it?
Is this a steel product to reduce weight? It is a steel product, but it has a hole in it moderately, which could be mistaken for a hole for fixing the Holder.
Although it does not have the noise reduction rubber like OEM products, its durability is no less than life, and its price is reasonable and the number of pins is abundant. When I was enjoying mini bike racing, I owned several types of Driven Sprocket to change the number of pins by CourseLayout and do some kind of setting.
[Included Parts:were they on?
One Driven Sprocket and one HolderPlate for fixing.
[Was there anything that disappointed you?
I have used them for over 30 years on various Honda-based Mini bikes and have never been dissatisfied or disappointed.
Originally, DriveSprocket is a discreet Parts and is covered by Case cover in NORMALSpec. Motorcycle, so it is a Parts that is only seen in terms of functionality.
Other items that would be helpful
Point and hang of installation
Since it is easy to remove and install, the work tends to be messy, so do not be in a hurry to make sure that you do not forget to tighten the screws.
[Availability and clarity of the Instruction Manual
There is no Instruction Manual, but the product is easy to understand.
[Notes]
Since you will be working on the drive and braking systems, be sure to carry out the work properly and reliably.
[ITEMS TO BUY TOGETHER
Aside from replacement for setting, if replacement is due to wear, the front and rear Sprocket & Chain are in the Quantity:This is a place that should be replaced by Set, so please consult with your budget before purchasing.
Since the rear wheel is to be removed and attached, if there is room, it is better to take the rear brake shoe into consideration as well, since it can be done in one operation, making it easier later.
[Opinions and requests to Manufacturer
I continue to be a customer for various parts of Mini bike and I look forward to working with you in the future.
View detail
Fits: YAMAHA YSR50, YAMAHA TDR50, YAMAHA Axis, YAMAHA JOG Zr, YAMAHA TZR50, YAMAHA TZR250, YAMAHA TZM50, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400, YAMAHA RZ125, YAMAHA RZ50, YAMAHA SDR, YAMAHA RD50, YAMAHA GT50, YAMAHA GT80, YAMAHA JOG, KAWASAKI KS-2, YAMAHA BW's, KAWASAKI KS-1
Idling is stable
[How is it used?
TZr250RS (3XV) The Idling of the Ignition coil was not very stable and the Piston ring was replaced.
Both OEM Parts and Uotani are expensive, but I was worried about the quality of Chinese products, so I chose this product.
Was the one you received as per Image?
It is quite Orange Body and Plug cord as shown in the picture.
The mounting bracket is only held in place by a screw and can be removed quickly.
Was the installation difficult?
Simply take the Mounting Hardware and replace it with the attached Ignition coil.
A plug cap is also required separately, but I used the NGK plug cap that was originally included.
The Right Side is just the right length for the cord, and the Left Side is too long as it is, so we cut it.
How was your experience with it?
Idling has stabilized considerably, although I have only been using it for a short time.
Both low and high RPMs have been used without problems.
I am satisfied with the resolution of the ailing area.
[Included Parts:were they on?
Plug cap is not included and must be purchased separately if needed.
And, of course, Quantity:1pc., so in 3XV, Quantity:2pc. Set purchase is required.
[Was there anything that disappointed you?
As others have mentioned, the Waterproof Cap is loose and the Ignition coil terminals are bare. (OEMs, too.) So Waterproofness is doubtful.
【Review】
Unstable Idling is now stable and comfortable.
It is a consumable item, and the price is not that high, so there is no harm in replacing it if you do not feel comfortable with the current situation.
View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA XR100MOTARD
Driven Sprocket17T
Purchased to get better fuel economy for ns1
Acceleration is worse, but fuel economy has improved, so I am satisfied.
Select 17T, the largest size
View detail
Fits: HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50, HONDA CRM80, HONDA CRM50, HONDA NSR75, HONDA NSR80, HONDA NSR50, HONDA NS-1, HONDA NS50F, HONDA MTX80, HONDA MTX50, HONDA MBX80, HONDA MBX50
About MechanicalSeal
Thank you for your prompt response.
I put it together as soon as it arrived. 。 Water leak cured.
I guess it's hard if you don't have a certain amount of knowledge. ??
View detail
Fits: HONDA Monkey R, HONDA Monkey R, HONDA Monkey R, HONDA Monkey R, HONDA Monkey RT, HONDA Monkey RT, HONDA Monkey RT, HONDA Monkey RT, HONDA NS50F, HONDA NS50F, HONDA NS50F, HONDA NS50F, HONDA NS50F, HONDA NS50F, HONDA NS50F, HONDA NSR50, HONDA NSR50, HONDA NSR50, HONDA NSR50, HONDA NSR50
CROSSCUB110 (JA60) Short Brake Lever for
I was looking for a Short Brake Lever for CROSSCUB110 and found this one after I mistakenly bought one for JA45 and spent over 6000 yen painfully. First of all, the price is about 1100 yen, and it is the best cost performance. The color is black, which is the same color as the Handlebar, and it matches well with it. The feeling of using it is like having a Large size hand. (Glove sizeXL) I can do it without any problem even with a 3-finger middle to small finger Brake on me Exactly. I am glad I bought it. View detail
Fits: HONDA MAGNA50, HONDA MAGNA50, HONDA MAGNA50, HONDA XR50 MOTARD, HONDA MONKEY RT, HONDA MONKEY RT, HONDA MONKEY R, HONDA MONKEY R, HONDA XR100MOTARD, HONDA NSR80, HONDA NSR80, HONDA NSR80, HONDA NSR80, HONDA NSR80, HONDA NSR50, HONDA NSR50, HONDA NS50F, HONDA NS-1, HONDA NS-1, HONDA NS-1
This is a classic, but it's the best.
This is the standard, but the easiest to use and I have used this many times. View detail