You can trust me.

I bought it from another Motorcycle and had no problems, so I trusted them. View detail

Beautifully made, perfect fit.

I'm really happy with the quality of these parts, they fit perfectly and look beautiful, they really add to the high quality look I was trying to create with Öhlins forks, Dymag carbon wheels and AP Racing calipers, Superb service from WeBike. View detail

Match CB1100 Fork with Initial ModelABS.

[How is it used?
The normal fork of CB1100 except RS has a caliper pitch of 62mm and 80mm. This item is for CB750 (RC42 ) It corresponds to 80mmPitch as well as etc.
The caliper side is compatible with bremboAxialCaliper 40mm.

Was the one you received as per Image?
The product seems to be Active and is working well with no accuracy or quality issues.

Was the installation difficult?
It is a Bolt On, so it is easy to install. In my case, there was a slight interference between the Caliper and the disc mounting Bolt base of the Wheel, but I was able to get it out by shifting it slightly.

How was your experience with it?
Since the Caliper position is at the top compared to the Fork of the 62mmPitch, it can go without the Hose extension. It also looks more natural.

[Included Parts:were they on?
In addition to the Instruction Manual, Bolt and Shim are included.


[Was there anything that disappointed you?
The quality of the product is not particularly problematic, but the high price is disappointing.
The recent price increase due to price revisions has made it even more expensive.

The same manufacturer's support with a 62mm pitch is often available, but the 80mm pitch one here may be special and is not available at all in the second-hand market. View detail

Fits front forks with CB1100 ABS of some years.

[How is it used?
I purchased the Fork/Caliper pitch 80mm/40mm to fit an older CB1100 Fork with ABS.

Was the one you received as per Image?
Quality is as high as the Image.

Was the installation difficult?
Basically Bolt On, but if it has ABS, it is better to install in Shop to make it work properly.

How was your experience with it?
It is well made and feels secure. I think it is indeed Active.
Recently, CHINA products have been distributed, but there are some cases where the products cannot be installed due to insufficient accuracy or defective products.

[Included Parts:were they on?
It comes with Bolt and Shim.

[Was there anything that disappointed you?
None in particular. Satisfaction level is high.

▼ CB750 (RC42) It is the same pitch as the Fork of the STD Disc and fits the diameter of the STD Disc. View detail

That's what Active is all about!

I purchased ActiveSupport along with my brembo equipment. I personally like this manufacturer and the quality and price are very attractive. I am very satisfied with the center and the quality of the product. It may be a little expensive, but it is a product that you can be satisfied with once rather than losing money buying a cheap one. View detail

I wanted a Size notation.

I bought it to use for bremboRear caliper center out, but the bolt size was for M10.
RearCaliper bolt cannot be used because it is M8.
There is no Manufacturer notation, only thickness, and I would like to see at least Bolt diameter indicated.

It is now in the collection of Parts. View detail

Purchased for installation of Brembo caliper

I bought this product to install Brembo caliper. The texture is good.
RightLeft and backside engraving for installation (Landmarks) It would have been nice if there had been a detailed Instruction Manual that would have helped me understand the installation orientation. I had a little trouble installing it. (Is it just me?) View detail

For Upgrade of Normal caliper

Converted from KawasakiZ1 OEMCaliper support.
Quintessential Over.
Aluminum Cut-out texture is the best finish.
We chose Silver to be One point.
The pad moves smoothly because the pad entry point has been polished. I use this pad with Vesra's Shim pad, and there is no squeal at all.
If you want to use double diskSpec., you will inevitably need two of them, but two Supports will cost 50,000 yen over.
It is a fun part, but it is a very satisfying part. View detail

V-max 1200 Rear Brembo caliper support

V-max 1200 Rear Brembo caliper support. Perfectly compatible with Brembo 2p calipers. It is also an overlacing product. View detail

For Brembo caliper!

I chose to use brembo's Caliper on my NINJA400.
Caliper brembo P4-40RB CNC 20.4756.67
Rotor SUNSTAR's Works Exhaust Spandex Z900Large Dia. 310mm, 5.5mm Thickness WTB25WR
Pad Endless SUPERHybridSintered EMP018

The center of Rotor and Caliper was offset 0.5mm inward, I put 0.5mm Shim on the Front fork side. I was lucky to be able to use the attached Shim by chance.
This Adapter is good to be able to Offset Caliper inside or outside by putting Shim.

When the Adapter or Caliper is installed while pushing the Adapter or Caliper against the Front fork side, the Caliper will slightly tilt counterclockwise.:Pair (for Left and Right) It needed to be asymmetrical. I was a little disappointed on this point. View detail

Exactly to the new Crab

As the Title says, it is Exactly to brembo new Crab.
The detailed construction is also carefully finished. View detail

It's a small thing.

I need it to change Caliper.
It's not very obvious, but I'm not sure if the Over text is a good idea.
Rear also wanted to Over. View detail

About Pad Overhang

I was casually looking at the new product introduction from WEBIKE, and I saw that the UP Type of Rear caliper support for the new Crab is now on sale from OVER, so I bought it.
I knew that there were some manufacturers that sold a rear caliper support for Crab, but all of them were of the type that was installed on the underside.

As for the installation, we would like to describe our concerns about the Pad, as we have received information from others about the Pad sticking out in their impressions.

First, I installed the Support+NewCrab on the OEMdisc and looked at the contact surface of the Pad and felt about 1mm of contact on the outside.
Next, we removed only the Pad of the new Crab and placed it on the OEMdisc with the OEMPad perpendicular to the OEMdisc. The height of both the Pad of the new Crab and the OEMPad were the same.
As a result, the Pad protrudes 1mm from the periphery of the OVER-made Support, so it is necessary to shave this off.
When shaving the new CrabPad, it would be helpful to trace the outer circumference with Magic or similar to give a guide when shaving.
In our case, we attached a carbide rotary bar to a cheap wired electric drill from Home center and scraped it off, but a File or similar may also be used for a diagonal drop.

If you continue to use an OEM disc with only Caliper+Support replacement, it may be safer to drop a little more than 2mm, since the chamfer of the OEM disc is larger than that of the MADE IN SUNSTAR disc. Therefore, it may be safer to drop a little more than 2mm.
*There may be some errors due to individual differences, so matching the actual product is the best way to be sure.

As for the weight, OEMSupport weighs 391g including the bolt and OVER Support weighs 299g including the bolt, which is about 92g lighter than OEMSupport.
Both of the mounting Bolts are replaced with Titaniumium Bolt.

The total of Caliper support + new Crab + MADE IN SUNSTARRear Disc this time made it possible to reduce the weight by about 400g, but the cost was also quite high, so I thought it was not worth the effort to change.
However, the BlackCaliper felt cheap with SP's Swing Arm, so it is now cooler.
The lightweight under Spring is … I haven't been able to run it that much yet, but it's likely that I don't know much about it. View detail

Pad protrudes from disc.

As you can see from the Up photos, the accuracy is very low. The disc is OEM, Caliper is when using brembo's new Crab. MT-09SP (2022). View detail

For REBEL.

WR3 is cheaper, but after reading the impressions, I decided to go with WR3.
I can use it without problems View detail

Excellent Craftsmanship

Took about 1 week to arrive. Compatible with my 2005 Vtec III. Looks and feels great! Highly recommended product with excellent craftsmanship. View detail

Wheel replacement for X

CarRear support needed when replacing WR250r with XWheel to make it MOTARD.
I was able to order OIL and other parts together. View detail

Complete Diversion

Purchased as a support to put Crab type Brembo on Takekawa's φ27Front fork. From OthersManufacturer, let alone Takekawa. Mukawaφ27for Front ForkCrabCaliper support." One-off is another option, but one-off is quite expensive. The offset to the Fork and Rotor was adjusted by Washer and Shim. The offset to the Fork and Rotor was adjusted by Washer and Shim. View detail

For brembo installation

Brembo caliper, SUNSTAR 320mm, radipon to strengthen the Brake! View detail

Crab type Brembo installed

[How is it used?
OEMFront brake not working too well so purchased to replace Caliper

Was the one you received as per Image?
It was perfect.

Was the installation difficult?
I asked the Motorcycle shop to install it without any problems or Trouble.

How was your experience with it?
Caliper can be mounted securely.

[Included Parts:were they on?
There was no shortage.

[Was there anything that disappointed you?
None

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail