Good product

Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail

Exactly to MOTARD as well.

Bought this for my drz400. For a long time, I had been wearing the one for my previous Large Motorcycle, but it was not so good because it was too loose. This time I bought it because it said "for Off-Road" and I am satisfied with the just fit. I also like that the lower part can be closed with a string. View detail

The size is just right and the texture is good.

Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner. View detail

Does not fit the KL250 Sherpa.

The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.

KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.

If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.

Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!

I bought it + even processed it so I'll be using it for a while lol. View detail

Z -WHEEL Aluminum nipples kx250 Front

Cost performance is better than OEM.
Nipple head (Rim side) is huge, so
Large amount of pop out from Rim
When installing the Tire, the BEET was not falling enough.
Tire is a little hard to fit View detail

It's a good product.

About quality and texture: I am glad to have received a plug that performs well.
About shipping and packaging: And the delivery was fast and accurate in all aspects. Looking forward to good deals in the future. About quality and texture

-------------------------------------------------- -------- About Quality and Texture: I am happy to receive a good plug. About Shipping and Packaging: And the delivery was fast and it was exactly delivered in every way. We look forward to a good deal in the future .about Quality and Texture Powered by Google Translator View detail

Purchased due to Headlight Bulb running out

I purchased these because the bulbs were out. The Pine Stripe bulbs were as bright as I expected.

It's also inexpensive, so it's helpful. View detail

I appreciate the affordable price.

[How is it used?
The KDX220 I purchased used was not in bad condition for an old vehicle from the 1990s, but the seat cover was in a slippery condition because the surface had begun to harden, probably because it was from that era.
On the way home after taking delivery of the car at Motorcycle shop, my buttocks moved back and forth every time I accelerated or decelerated, making it very difficult to enjoy the ride, and as soon as I started driving. The first custom was to reupholster the Seat Cover. It was like that.
Originally, I was going to bLOOVE it, including a look at the vehicle, but I went home right away and looked at Webike's product introduction section. KDX220 Seat I've been searching for...
Since it is an old vehicle, there are not many choices, but I-Net's Off-road Vehicle UniversalSeat Cover was a hit, and the price is low! If by some chance I fail, I'm ready to give up." So I bought it
How did you like it?
As a universal product, it is not as good as the Seat fabric made by a three-dimensional manufacturing process for each car model, but I personally think that the KDX Seat itself is not a complicated shape, so I was able to stretch it well.
The new fabric is highly flexible and the dimpled finish gives it a high grip, so you can enjoy riding without being carried back and forth every time you accelerate or decelerate.
To be honest, I wanted to stick with the OEMSeat Cover, but after looking at the price, the thickness of the fabric, and the condition of the finished product, I felt this product was sufficient.
How did it compare to other products?
There are few choices in terms of car models to begin with, and other products are expensive and have stopper belts sewn into the seat surface. I mean it!" I couldn't choose one because I had a strong feeling that it would be embarrassing to me, as I have poor driving skills.

What points should I pay attention to?
Patience and ingenuity are required because the products are not three-dimensionally sewn for car models.
If the tucker is driven in too shallow, there is a risk that the fabric will break from the tucker.
Front and back of the Seat are loosely secured to the Quantity:Pair (for Left and Right) When pasting the "Beauty" sponge, it should be pasted along the "Seat sponge" without wrinkles to make it beautiful.
Other items that would be helpful
The deciding factor in the purchase
The only Seat fabric that was safe for normal use was sold only by iNet.
We were not able to confirm that the products were made by KawasakiOEM, so we did not consider them in this case.
[How is it used?
Basically, it's Main for city driving. I can't even use SEROW, so it was too Hurdle for me to play in the mountains with a 2CycleEngine equipped car.
【Included Parts:presence or absence】.
Seat CoverQuantity:1pc. with Instruction Manual and Vinyl for waterproof.:Set
Tandem belt is not included, so those who need it must purchase it separately or reuse the OEMBelt.
[ITEMS TO BUY TOGETHER
Seat fabric to fasten to Seat Base seat. Tucker. and short-legged core.
It may not be necessary for those who apply Vinyl underneath, but for those who apply directly to Sponge without Vinyl, it is better to prepare SiliconCoking agent to be applied to the reverse side seam of the Seat fabric.
Opinions and requests to Manufacturer.
Although it may not be a problem for popular cars, it is a product that older cars and minors cannot do without, so we hope you will continue to sell Lineup for a long time. View detail

Regulators are consumables.

For the past year,,, my car TW has had certain symptoms.
The small light bulbs such as Blinker and Tail lamp frequently go out... and the Headlight Bulb frequently goes out. 。 The battery also went up frequently...each time I changed a new Valve or battery, but there was no improvement at all.
I thought that the vibration might have caused the Valve to break, but it was so frequent that I became concerned.


I checked on the Net and asked a motorcycle shop, and they said it might be a regulator. I asked a Motorcycle shop....

from the start "Regulator." What is a "what"?
"Regulator." The "PARTS" are the parts that mainly play the role of voltage control and rectification, in other words, they are the organs that mediate the delivery of battery power to the car body.
If there is an abnormality in Regulator

(1) Battery leaking → sometimes smelly (lol)
(2) Headlight is becoming → easier to break.
(3) Charging does not take place → Replacing with a new Battery did not help.

Totally my symptom (laughs).

If this part is broken, high or low current will flow due to the ineffective power regulation.
In other words, in my case, I thought the Light or Blinker was cut off by the high current.

I tried to check the Manufacturer's Sitec. and asked questions directly to the Manufacturer, but they did not give me a clear cause of the problem. It's controlled by semiconductors with no contact points, so it basically never wears out." Responses such as. I guess the→regulator had no way to answer because the lifespan is basically not clarified (laughs).

But in fact, the Regulator is out of order. (Puncture) I do.
After Regulator replacement, symptoms such as battery degradation and blinker breakage were completely fixed. Proven.

According to the motorcycle shop, there were some single-cylinder, medium-sized, and small-type owners like myself who had experienced one failure each among the three models they owned.
"Incidental symptoms..." In fact, the explanation that "the problem is not a problem," cannot be taken seriously. In fact, the Parts replacement improved the situation, and 。 Understand that it is consumable.

Also, Regulator failure. (Puncture) The "H" is said to occur more often in medium and small engine displacement volume vehicles than in large engine displacement volume vehicles. Especially in air-cooled
So what caused it in the first place?
The one that is said to be an improved version of Regulator has a heat sink, which is a heat-resistant spec. added to it, Regulator failure is caused by heat. It is easy to predict that

Is it age-related deterioration, or is it the heat generated by the air-cooled single cylinder?


good point
◎After replacement, Battery degradation and lighting of lights were stabilized.

◎Engine startup is also improved.

◎Axel is now better.

◎Meter movement is also Smooth.


In the end, all areas related to electricity were improved.
It's been 20 years since I bought it used... I don't know how it worked without regulator replacement (laughs).


If you have an older vehicle and the batteries are deteriorating quickly, or if you have problems with the lights, you may want to think about replacing the regulator.
It will be in good shape when you replace it. View detail

Is there a problem with being thinner than OEM?

I'm sorry I couldn't provide a photo, but when I used it on my NINJA2 Helmet 50RSL, I compared it with the OEM one, and the shaft part that holds the pad is clearly thinner,
The measurements were taken from the OEM, so they should be the same diameter." This was the case
I have a question for those who are familiar with Brake, is there any particular problem with the thin shaft part?
Has anyone who bought the same Stainless Steel Pad Pin had a similar case? I would like to hear your opinion. Thank you in advance. View detail

Useful for cold season commuting

[How is it used?
installed
Was the one you received as per Image?
Grip is Slim and good.
Was the installation difficult?
Left Side Grip is difficult to install. How do we get there?" I struggled with it for about 15 minutes. I hit it with a board and tapped it in with a plastic hammer, but the Motorcycle shop advised me not to do it as much as possible because it could be damaged.
How was your experience with it?
The product Single Body is warm, but it is even more effective if you use Knuckle guard, Cover, or other devices to protect it from the driving wind.
[Included Parts:were they on?
Everything was in place.
[Was there anything that disappointed you?
Sufficient performance is not a problem. View detail

Used for WR155

[How is it used?
I used it to replace the YOSHIMURAExhaust System on my WR155.

How was your experience with it?
It is usable without leaks of exhaust Gas.

How did it compare to other products?
I have never used KITACO and OEM, but KITACO quality is close to OEM quality.

[Points to note]
If not tightened firmly, it will leak.

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer

nothing special View detail

More rust-resistant than OEM Product

I used this for an overhaul of a very old OEM Caliper. The previous owner had maintained it to some extent and it was not so badly worn, but I wanted to assemble it in a new and clean condition if I was going to overhaul it. I chose it because I wanted to assemble it in a brand new and clean condition. View detail

Required for Northeast Number.

The grip is so thin and natural that you don't even notice it has been replaced. View detail

I am very grateful for this season!

My other car is equipped with a Grip Seater at Standard Equipment, and in the middle of winter, I have been benefiting from it, so I installed it on SecondMotorcycle as well.
As a result, WW could be a little warmer.
I guess the performance is a consideration for Battery capacity, etc., but if I had my wish, I would prefer a little more warmth...
The product looks and feels completely comfortable to hold.

Having said that, I have been able to spend this winter more comfortably than if I had nothing on! View detail

ALCAN hands iGrip

I have used it for VTR250 and MT-03, and I bought it again this time. The color is Orange red to match the body color, and it is a good accent for the handlebar. When I installed it, I used a small amount of glue to prevent shifting and decided not to use wiring. View detail

Water pump pliers

Even a light press-fit clip can DID be tricky, requiring a press-fit of the plate to create a groove to stop the clip. A cheap chain tool often fails to press-fit the clips properly. If you use a water pump pliers to tighten the 6mm nut to the plate with force, you can get a groove for the clip. I do not want to buy a Stripele for my own use, considering the frequency of use. View detail

DJEBEL250xc.

Installed on a DJEBEL250xc, cutting off the OEM ignition coil in the middle and connecting it. It is a recommendation to refresh the electrical system. View detail

More than I expected…

I bought it for winter touring because I had some points left over and there was a discount campaign going on.
I can do electrical work and have replaced grips before, so I installed it myself.
Installation was easier than I expected, but it is safer to ask a store to do it if you are worried about the force required to press-fit the grips.
The key heat is effective at Plus temperatures, but not so effective at Minus temperatures. Well, it is better than nothing.
I have a Honda 400X with Honda OEM hand guard, so it is not directly exposed to wind, but even so, the effect starts to diminish from about 3 degrees Celsius.
It is better than nothing, but when I experienced HondaOEM's Grip heater on the 400X I rented from LenBarrel at HondaDREAM before, it was so hot that I could not grip it even at high speed in the morning in the middle of winter, and 2 out of 3 levels was enough.
This product does not get that hot even at max. 5 levels.
It seems that the temperature differs depending on the Manufacturer, and KIJIMA-made products seem to be lower than those of other Manufacturers.
Power is supplied from Honda OEM power supply coupler ACC.
However, the grip is very good, so I will give it an overall rating of 3.

Good points:comfortable grip and easy to install.
Five levels allow for detailed settings depending on the situation.

The bad:Not as hot as expected. View detail

Not yet experienced

I think Road works better than OEM, that's all I can tell you right now, but I haven't experienced what happens when it's off. As for the Pad, it didn't squeal without the chamfer. View detail