Reviews
Genuine DID 520ERVT Replacement Chain Link
I always like to have some of these in stock in case of any issue during fitting different chains. The DID 520ERVT is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get the white grease packet in this size chain so that's always a good thing, I have a lot of these anyway but you cannot have too many. The chain link is very well made one, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. I keep the rivet link type and this clip joint type but had ran out of this version, hence the purchase. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
Genuine DID 520 Replacement Chain Link
I always like to have some of these in stock in case opf any issue during fitting different chains. The DID 520ERT3 is one I do have in stock but have no spares. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get a not seem to get the white grease packet in this size chain but that's ok, I have a lot of these anyway. The chain link is very well made, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
TZr50R Oil Filler Cap O-ring
[How is it used?
Used for EngineO/H of YAMAHA/TZr50R.
This item is an O-ring of Oil Filler Cap.
It is not a part that needs to be replaced, but we replaced it because it was a good opportunity to do so.
How was your experience with it?
OEM parts are the only choice for engine parts. There is no problem with quality.
I compared it with the old O-ring, but the old one was still hardened.
Oil does not leak from this area, but does it affect the pressure application?
How did it compare to other products?
There is no Other Brand Product, so there is no comparison. Even if there were, OEM would be the only choice.
[Points to note]
I installed it while taking care not to twist it during installation.
Grease is also applied just in case.
View detail
I'm too weak.
It was distorted when I fell and hit it.
With OEM, this didn't happen even if you hit it hard..,
View detail
Genuine Yamaha Right Side Swingarm Cover for YZ125 2004
This was a replacement for a totally missing right side swingarm pivot head from the YZ125 that came in to the garage. I also had to replace the left side as that was also missing. No idea how they were lost but they were certainly not there. Finding the right covers was pretty straight forward by checking Yamaha schematics. The price was great and this made me very happy. With a few other small parts, my order was shipped with EMS and as usual, it arrived at my door in 5 days straight. Everything in the order was packaged very well and no damage during transit. The cover is a moulded one made from what looks and feels like a plastic composite. It is a very hard surface but that is a good thing. It is just a boot that goes over the pivot head and protects this from rocks and debris which swould hinder the removal onf the pivot. Fitting was just a push on cover and was very secure as I did try and prise it back off but it was well on there. Nice little job that made a good difference. Thanks Webike, nice one View detail
For CB250F
.Actually this item i could not found in my country (VX Series Joint Link 520VX3). Finally I bought it from webike. It is original. Very good packaging.fast shipping.I am happy to deal with the webike team View detail
Z -WHEEL Aluminum nipples kx250 Front
Cost performance is better than OEM.
Nipple head (Rim side) is huge, so
Large amount of pop out from Rim
When installing the Tire, the BEET was not falling enough.
Tire is a little hard to fit
View detail
Genuine Yamaha Front Wheel Oil Seal for WF450F 2017
This was the oil seal for the front wheel on the WRF450F which needed new wheel bearings. I do always replace the oil seals when it comes to any bearings where possible for my own peace of mind. It just makes sense to do this. Finding the right oil seal was easy as I already had the schematic open for the wheel bearings anyway. The price for the new seals was great value. At this price is was silly not to get them. With the other parts needed for this replacement, I had all the order shipped using EMS which are my chosen and trusted courier. My order arrived in 100% perfect condition in 5 days from being shipped. The oil seals came in th standard Yamaha packets and were also inside a nicely made bubble wrap envelope by Webike warehouse to keep them safe. The oil seals are pretty rigid if I am honest but that is not a bad thing. They are top quality oil seals which you expect from such a well respected manufacturer like Yamaha. With a tiny bit of oil to seat them easily, the job was complete and now the front wheel moves freely and smoothly as it should. Great job guys, very pleased with this purchase. View detail
Changed from Clip to Crimp
When replacing the chain on the KLX230R, the ERVT came with a clip-type joint, but the clip didn't fit well and I had to press-fit it too much and it failed, so I decided to use a Crimp joint, which I am used to.
I think the Crimp is fine for me, and the Crimp is easier to work with because I'm used to it.
View detail
Fits: SUZUKI RM-Z250, SUZUKI RM-Z450, YAMAHA YZ250F, YAMAHA YZ450F, YAMAHA YZ250FX, YAMAHA YZ450FX, YAMAHA WR250F, YAMAHA WR400F, YAMAHA WR450F
Used in CB250R
Used on CB250R.
Pipe is a little long, so cut about 3mm for a just fit.
The amount of Throttle manipulation was reduced by about 16%, making it easier to ride.
View detail
durability
I use it for its durability.
(10000-30000km)
View detail
The XG250 TRICKER has a slightly smaller take-up diameter than the OEM.
Purchased for installation of hand guard to be fixed to Bar End.
I installed it on my XG250 TRICKER and the take-up diameter is a little smaller than OEM.
I felt no discomfort when I rode it.
It was easy to open end for now, so that was helpful.
View detail
Genuine Yamaha Gasket for XT250
Whilst I was changing out the oil and already purchased the new oil drain plug, I wanted to make sure I had a good seal so also purchased the genuine Yamaha gasket for this bike. This is only the second oil change I have done on this bike but it is only a 2019 model anyway. The correct gasket was found when I checked for the correct oil plug. Not too tricky when you have the Yamaha schematiics in front of you. The price was really good value, yes, you could get a pack of cheaper after market gaskets but for this money, why would you risk a good seal. Anyway, with a couple of other parts I needed including the oil plug, I had my order shipped using EMS. My order arrived in perfect order and 100% no damage in 5 days straight. The gasket was in the usual Yamaha clear packet. There were no contaminants inside the packet which was nice. The washer looks to be copper but I would assume it is a copper and some other metal mix. Easy job to do replacing the gasket and oil plug but make sure not to over tighten. Use a torque wrench and make sure you have it right. Very happy customer. Great work Webike. View detail
Genuine Yamaha Plug Straight Screw for XT250
One of the only parts I do insist on changing is the oil plug on bikes after and oil change. Mostly due to the screw becoming a little messed up and could be harder to remove over time. Even though this bike is a pretty young bike, it has a lot of years left in it and I would hate to have to drill out the bolt to change oil in the future. The correct part was found by using the tools Webike provide on their help section. I then did a cross reference with Yamaha schematics to make sure. The screw was not expensive but when you get a genuine Yamaha one, you know it will be perfect for the job. With a few other parts, my order was shipped using EMS and arrived in one piece and perfect condition in 5 days. The screw came in the standard Yamaha packet and wrapped in bubble wrap envelope. It was really clean on the threads and no shards or swarf were found. Along with the genuine Yamaha gasket all was fitted eas=ily and no leaks once torqued correctly. Very pleased witht his purchase. Cracking work Webike. View detail
Large satisfied
I have been asked by my daughter for a long time, but due to the severe cold weather this year, I bought it. (Scooter) So I had a hard time removing the cowl, but I am Large satisfied with the contents of the product. I have several other motorcycles, so I plan to purchase & install them one after another. I think it is very cost effective! View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ250X, YAMAHA YZ450FX, HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FE250, HUSQVARNA FE350, HUSQVARNA FE450, HUSQVARNA FE501, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TC85, HUSQVARNA TE125, HUSQVARNA TE150, HUSQVARNA TE250, HUSQVARNA TE300, HUSQVARNA TX125, KTM 125EXC
Blue looks great in WR.
It is a simple nut, but the OEM is extremely simple, so the blue stands out and is a good parenthesis. The anodized surface of the tool contact area is inevitably peeled off because of the large torque applied to this part. I would like to know how to prevent damage to the surface of the nut since it is a part that is removed and attached quite often. View detail
Front sprocket replacement
Since the rear sprocket was replaced, the front sprocket was also replaced.
The OEM is 14T because we want acceleration, but this time we will replace the Front with 13T.
Lowering the front sprocket sacrifices fuel economy and top speed, but I want the acceleration that makes it easier to ride with WineDINK….
Nut is a 32mm Socket.
I haven't ridden it yet, but I am looking forward to seeing how it will change.
When I changed the front sprocket, I also purchased the OEM 14T so that I can change it back if the characteristics are too large to fit.
View detail
best grip heater
This is 3rd time i use Kijima grip heater. I think this is the best grip heater, it is thin as original grips and included aluminum tape helps hold the grip quite strongly on the handlebar without addhesive, of course need to make effort little bit to install. View detail
Genuine Yamaha Ball Race 2 for YZ450F
I have done a lot of work on this bike for quite a few years and the ball race was needing to be changed. I already knew the part number from the previous fitting but still cross referenced from Webike help pages and Yamaha schematics to make doubly sure. The cost of teh race was really good and better than could be sourced locally. I always have a few other parts in an order at once as this does save me on the shipping fees. I used EMS as they just get the parts to me fast. Within 5 days from shipping my order was delivered. The race came in teh Yamaha packet and was also inside a bubble wrap envelope for safety. It came in great condition and the race is did not have any sigh of damage. This fitted perfectly and made a whole load of difference to how the bike stabilised. Very impressed with how well it all worked out. View detail
Huge upgrade over stock pegs,Excellent quality and Wide sturdy grip.
Very solid footing with these and they have already withstood a couple of hard falls! Surprising what a difference these make compared to stock! Excellent pegs. Feels like a have a front porch worth of room for my feet to stand on, and they grip to the bottom of my boots like super glue. Easy to install and improved grip noticeably over stock foot pegs.I will say you may have to tweak your stock peg springs to fit around these monsters but still only took 10 min to install both. Great Product, Highly Recommend,webike too fast shipping View detail