It's so cool!

To be honest, it's a little expensive for Bolt, but it's just good looking! Use Gold attribute polish regularly. "polish" It is necessary, but it is also part of the fun! Natural Brass color that is not obnoxious." It is also a high point that it does not stand out too much! It stands out casually, so you can see it many times while touring. Where do you sell it?" I recommend it to those riders who know the difference! View detail

10mm diagonal is helpful.

AP racing's NORMALBreeder has rusted badly, so we replaced it. The size is 11mm diagonal, which is very rare in FOR JAPAN MODEL, so now we can use 10mm Spanner Glasses instead of MONKEY Wrench, which improves the workability. I'm satisfied with the new size.
This is a RECOMMENDATION because it is definitely easier to use than the NORMAL with the Breeder still at 11mm. View detail

Parenthesis is good

The look is nice, the texture is nice, and it has Logo and Parenthesis.
It is small in size, but sufficient as a side bag support. View detail

Purchased as a spare

The last one I purchased was quite scratched and worn, so I repurchased it as a spare. This time it is twill weave.
We initially waited 8 months but received it in 6 months.
After all, delivery time for carbon parts is usually around 6 months..., View detail

Handlebar vibration reduction

[How is it used?
Commuting and Touring.

Was the one you received as per Image?
Both the packaging and body were better than I had imagined, with a higher quality.

Was the installation difficult?
The manual is very thorough, so there are no problems. General tools are sufficient, but it might be better to use a Torque wrench since the Bolt and Nut are described as Torque in various places. (20N-m to 90N-m)
I did not know the jack-up point for replacing the shaft of the engine mount, so I jacked it up at the appropriate point, but the shaft itself came off without any trouble, so I felt that I did not need to jack up the shaft. (There are descriptions of applying jacks to the Exhaust System, Oil Filter, etc.)
The replacement itself takes about 30 to 40 minutes, and the difficulty level is about normal for those who are familiar with maintenance. However, if you do not have a torque wrench or jack, or if you are not confident about loosening the engine mount, it may be safer to take the engine to a shop.

How was your experience with it?
Vibration was dramatically reduced and the effect was easy to see.
The flopping sensation is reduced and the car feels sturdier, even on rough roads and continuous gapping.
However, I think that the vibration damping on the Frame side plays the role of Large Kinashiro, and there was no change in the impact when passing through the Large Kinashiro Gap.

[Included Parts:were they on?
Complete set shown in the product photo (Clamp, shaft, bolt nuts, etc.), Owner's Manual (Installation Instruction Manual)

[Was there anything that disappointed you?
I am generally satisfied with MinusPoint, but the price is a little over 40,000 yen (+α labor cost), so I am not sure if I would recommend it to everyone in terms of cost-effectiveness. I recommended it to my acquaintances, but they did not respond well. My impression may change depending on the level of dissatisfaction with the vibration of my car. (I don't think the vibration of sv650 is that large, but I am satisfied with it because I am of the opinion that there is nothing better than having no vibration). View detail

Wick Visual Bureau Wick MotoGPLogo Official Ste.

As one point, I bought it and put it up.
At a roadside station where we took a break during the touring
You look great!"
Parenthesis is a great Sticker!
It looks great on the Motorcycle!"
They called out to me, "I'm sorry, I'm sorry, I'm sorry, I'm sorry.
Feel the DNA of YAMAHA motogp TEAM View detail

Mounted on CROSSCUB110 JA60

My favorite is the color Black and the heavy bass sound.
Power is also up! View detail

Happy to reverse shift.

”Reverse Shift is not possible with the Automatic shifter. "Oh, really …" I can't believe that the Reverse Shift, which can be done by changing the Shift arm up and down, is not easy to do! After some research, I found that the Sensor of the Shifter does not respond to the angle at which the Shifter is mounted. I was looking for a footpeg that could be used for Reverse Shift, and I found Babyface, which is compatible with Reverse Shift from several other companies, but I had to buy it as a separate part, and the cost was really low. The feel of the product is solid and very good. I don't feel that it is cheap in any way. The only thing that bothers me a little is that the tips of the Shift and Brake are hard.:I would have preferred Rubber since it is made of Plastic. But don't worry, it won't hurt your feet at all. By the way, the compatible car model is -22 years old, but it can be installed on the latest model 24 years old without any problem. I asked Webig to confirm it for me because I was worried about it. Thank you very much! View detail

Parenthesis is good, but ….

The OEM grips were a little too thick for me, so I bought the thinner domino grips. The product itself is Wow, Parenthesis is good. The tension was raised like this, but the feeling of use is very thin, so the handling of the motorcycle is very large and I even feel that the motorcycle has become heavier by about 10%. When I am running the bike, I can feel the weight of the bike. Maybe a little too thin." It was like that.
Roughly speaking, a Grip that is too thin with a body that weighs about 190 kg will simply be difficult to ride. View detail

Purchased White for Decal paste

I bought White to match Decal. 。 The OEM YAMAHA Logo has a convex shape, but this one is plain and can be applied cleanly.
Relief shape other than Logo and others are similar to OEM!
The OEM did not think anything of it.
It goes on easily, but I wonder if the Body of this one is slightly deformed.
Hole position did not match Exactly.
Screw one of the first three holes at the end, and the other holes are used for the Body.
The holes were aligned as if they were pushed in or aligned with each other, and the screws were inserted into the holes without any problem.
Be careful not to insert the screw into the gapped hole by force, as it will enter the screw at an angle and damage the screw threads on the fork side.
There is no distortion after installation, and the gap between the Fork and the Fork has been properly taken care of. View detail

It looks better after adding Emblem.

Due to the long W800 two-pad, a shorter width Emblem was selected.
We wanted to install an Emblem with Large letters, but decided against it due to its long width, which would have prevented interference with the Ni-Pad.

It is not possible to attach Exactly without bending it slightly to fit the tank shape, but it is easy because it is soft.
I had a little trouble with the positioning of the two-pad, but I think I managed to settle on a good position. View detail

GOOD GOOD Glass Wool Acoustafil

Cutting is accurate and no cutetc. is required.
The Glass fibers are braided and compressed thinly, so there is virtually no scuffing of the Glass fibers.
(but protective equipment is still required)
The compressed Seat is temporarily fixed with Tape and expands with heat after assembly.
The work of putting it in the tube is easy.

The purchase cost is usually a problem instead of the difficulty of the work being reduced compared to Glass Wool.
Silencer parts removal & disassembly, Rivet removal by Drill,
Rivet re-fixing, hole alignment, and removal of remaining gasketetc. using special tools,
Parts matching checks and other su-kills are necessary.

One 1100mm-long Seat is equivalent to one Silencer.
Two Silencers would require two pairs. View detail

Consumables Replacement

I had one on my previous Motorcycle. Replaced with this one again.
The finish is not as good as it should be because it is resin parts, but it is sufficient for the needs.
Fitting is also no problem. View detail

AELLAShift holderNINJA1000SX

Easier to install than expected.
I think I'm going in with GEAR or Snap.
Cospa is not that high. View detail

Fits 23-year 400X

I've been trying to find out and inquire if it will fit a 23 nc56 400X.
I could not confirm it, but I was able to install it.
It seems that the brake master is different from the previous generation SingleDisc brake models.
Installation was easy. View detail

To change the oil.

Purchased to replace Element along with Oil replacement.
It was well made and worked fine. View detail

The single piece of leather Belt is the best!

[How is it used?
I had been using an elastic belt, but my Rider Pants were falling down and I was looking for a leather belt. The results of the survey were as follows.

Was the one you received as per Image?
The quality is better than I expected, the leather quality and manufacturing is good.

How was your experience with it?
Large also means Small I bought the L size in the "Waist" section, but the size length in the product description was the same as Waist and OK. My Waist is 85cm, but it was a little too long.

[Points to note]
We recommend that you purchase on your own Waist Street.
The buckle part has a ring with giza to make the belt more flexible, but the inside of the ring rubbed against the buckle body, causing the black-dyed part to peel off and create a rust. It is not visible from the outside, so it is OK.

How did it compare to other products?
I think that most of the recent Belt products have elasticity, but I think that a single piece of leather Belt is also good.

Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer View detail

Fit feel on par with OEMs

Thank you very much for the Chain tensioner. The installation is completed by Bolt On, but I adjusted the tensioner by overlapping the attached washers so that the chain would be more centered on the roller. In my case, I used all the washers to get the quantity:I was able to set it. I could not feel the running performance, but I think it is useful to reduce the flapping of the Chain. However, since the tension is not always applied by Spring, it is necessary to adjust the tension of the chain. Just a little... View detail

Good for Normal tank cap

I bought it to use for a tank cap for my Accosat, but after receiving it, I realized that the Bolt shape was different and never used it.
It can be used to change the bolt on a normal tank cap, so I think it is an easy way to dress-up the cap!
Purchased for ZrX1200R.
Bolt size is the same, so I think it can be pontooned. View detail

economical

I bought the Oil Filter ahead of time because I will be replacing the Oil Filter at the next Oil change.
It is a great value and helps because it comes with the necessary Packing in addition to the Filter and you don't have to buy more.
If there are no problems after using it, I would buy it again. View detail