VINO125

The size and shape were the same, but a little cutting work was required, so if you have the tools, you can install it on the VINO125! View detail

Weight reduction around handlebar

I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.

Until now, I have been using ZETA's Guard with Aluminum in it,
The Handlebar end of the Motorcycle, the furthest end of the Motorcycle, is extremely heavy, and with the worsening of the Handleling,
I was struggling with the weight of the Motorcycle when I knocked it down.
Also, the fat bar's bend also became a snap, and for a long time we were troubled with the selection of a hand guard.

To be honest, this hand guard works. However, it can be easily fixed by hand, so I am not particularly dissatisfied with it.
Since it is not made of aluminum, it is very lightweight. The lever protection is also very good, and so far it has protected me well.

Total performance is very good. It seems to be my ideal Hand guard.
I would like to test how far it will endure while actually using it, since it is plastic in nature.
By the way, although it is Plastic, it is surprisingly sturdy. View detail

KAISOKU

So many parts are in Quantity:I was very happy to be able to purchase a set! It is a well-known manufacturer and I was able to experience the results, so I have nothing to say about it. It would be helpful if you could describe in more detail the car models to which the product is applicable. View detail

finally

I finally got my hands on Clutch, and I'm happy to say that it worked as well as I wanted it to! I'll have to look into buying the next part again! View detail

This is what it looks like when installed on a KTM 2013 DUKE.

This is what a BMConti2-type Handlebar looks like when attached to an Initial ModelDUKE. Finger is about the same height as Limit. View detail

exchange

I managed to attach it successfully by replacing only the cover. View detail

To use Point

I recently used it in a Tire replacement.
I was A little inquisitive as to whether this was the right way to use it. View detail

A bit pricey.

With bar ends made entirely of gold, the basic rule is to replace the bar end when it falls over, but in this case, only the resin part can be replaced, so there is no need to buy a new one if it is just a standing bump.
However, the replacement of the resin part is a bit Large strange. View detail

Lightweight bar ends from KIJIMA

Lightweight bar ends from KIJIMA, ideal to save some weight while still maintaining some vibration damping efects. Can be use on both the stock steel handlebars or aftermarket aluminium ones, as it cames with both adapters type and the Allen tool also. Overall a good quality/price product. View detail

It is easy to install.!

OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good. View detail

I did it anyway.

Slip-on lineTruck di, and I put it on!
The look of the first Silencer in the shape you're interested in is self-satisfying.
It is not too much, but it is something better. By the way, as soon as I put it up.
The material is aluminum, so it looks like a cord when peeled off.
I hope that the heat will make it disappear. I hope the heat will make it go away. View detail

The written Size is different.

The size is written, but the length was 75mm. The width is
Is there something about Sticker, or is there a notation?
Photos are uploaded for reference. View detail

light

[How is it used?
After installation, the car traveled about 200 km.

Was the installation difficult?
It is not so difficult to install except for the Flange, which is a type of two-piece flange, so it is difficult to install unless you get under the motorcycle.

How was your experience with it?
The OEM one is quieter, both idling and running, but the OEM one is louder. Personally, I was satisfied with the quietness, as it was just right for me. The sound quality is not as harsh as the OEM, but low and smooth.
Lightness is somewhat felt when pushing and pulling.

[Was there anything that disappointed you?
There are too many springs to install, but since spring hooks (devices) are not included, it is better to prepare them.

[Others]
Point or hang for installation...nothing special. If you dare to say so, there is no need to twist the O2 Sensor when installing it. If you install the O2 Sensor lightly before fixing the middle Pipe and turn the Pipe side around, you don't have to worry about the O2 Sensor wiring twist.
Availability and clarity of Instruction Manual - I can understand without it.
Items to buy together...Gasket is a good thing to have. The only other thing I need is heat resistant grease.

【Review】
Personally, I don't like the length of the exhaust end, the degree of raising, and the color (I prefer shorter, lower, and Polished Titaniumium), but I am very satisfied with the lightness, the Hand Bent-like curve of the exhaust pipe, and the high quality sound. View detail

CHINA.

[How is it used?
Street Riding and Touring
Was the one you received as per Image?
As per other reviewers.
Was the installation difficult?
Replacement with Mirror Lens was difficult. There was a Crack on the Lens from the original and it spread during removal.
The Nose guard was also difficult to remove and left a mark.
How was your experience with it?
This is my first time using Goggles and it worked exactly as I imagined it would.
There was a sensation of a nose being crushed.
[Included Parts:were they on?
Sticker and LensFilm, Film mounting stand
[Was there anything that disappointed you?
It was unfortunate that the 100%Logo paint was peeling.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail

Neoprene Gloves

[How is it used?
Winter Touring, Bicycle commuting in the middle of winter
How was your experience with it?
Palm is synthetic leather like KUSHITANI's summer gloves?
Motorcycle gloves are tough on the instep even with a Grip heater on.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail

First time Inner protector

With one of these, you can use it all year round.
I used to wear Protector jackets, but they were tacky and I had to change them with the seasons, which was inconvenient.

Chest Protector is a little unreliable, which is a complaint
If you're worried about it, you can just change the chest area.
I wear a t-shirt on my chest in the summer anyway, so I don't think you can tell the difference from the outside, even if you use a different Protector.

170 cm, 62 kg, standard build. View detail

Smartphone Holder KaEdia

This Holder can be easily attached with the included Hexagonal Wrench. It has an Attachment for any Motorcycle. It is very easy to operate and you can fix and remove the phone with one hand. I am very satisfied with it. View detail

Exhaust System replacement

I replaced it with YOSHIMURA's Exhaust System to see if it would have some effect. I was surprised to find that the overall acceleration was smoother and more effective. View detail

I think it would have been better if it were a little thicker.

The fabric is too thin. The texture would be better if it were thicker. View detail

It became a little Fashion.

The purpose of the parts is to make the Indicator Lamp easier to see. Of course it has that effect, but I think there is a little change in aerodynamics.
I feel strong wind pressure when I reach about 100 km/h at high speed. After installing this Visor, I felt it was reduced a little.
I recommend it to anyone who wants to do a little something better. View detail