Reviews
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
WhiteLight and good looking!
It's super easy because all you have to do is change the Valve.
I was able to purchase Valve's length and fit without concern because of the information provided by its predecessors.
D-TRACKER-X's dark, orange-tinged light has been brightened to white.
I haven't driven at night yet, so I haven't been able to experience the true effect, but the impression of the motorcycle will change considerably just by having white light.
View detail
Bright and low power consumption
I was worried about whether I could install it on my KSR2 since the body is longer, but I saw the impressions of someone who had already installed it on his KSR and he said it could be installed, so I bought it and installed it.
The length was a limit, but I was able to install it, the Others had no problems with the installation, and the rubber cover went on without modification.
The beam coverage has been widened. The optical axis remains the same and is large and sturdy. The high beam illuminates high up and is even brighter, so you have to be careful of oncoming cars.
I also changed the tail lamp to LED, so the power consumption was reduced a lot. I installed the LeftSwitch of the previous model in my car, so I can switch from LightOff to Light when Halogen is on.
Idling dropped about 200 RPM when switched to On, but switching from LightOn to LightOff when LED has no effect on Idling.
View detail
I put it on my RG 50Gamma.
It's just like changing a light bulb.
There is no problem
View detail
subtle
Perhaps it is because the Scooter has a low power generation rate, but I feel that the Halogen bulb has a wider beam range and better visibility.
This might be better with a slightly better Halogen bulb.
View detail
It works well
This is a 2007 ZOOMER.
The mileage is about 6,000km as I only drive it occasionally, but the Brake squeal was getting worse, so I replaced it.
At first, the effect was not so good, probably due to the lack of hits, but then it started to squeak.
When I disassembled it, I found that it was still on one side, and after licking the perimeter with a file, it looked better.
I am satisfied with the soft but firm feeling of working well.
Durability is not yet known.
View detail
Headlight LED
Installation was easy. It was brighter than I expected. View detail
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
Very good Touch!
This is a 2008 ZOOMER.
The mileage was only about 5,000 km and it was still usable, but it started to squeal and work poorly, so I replaced it with a reliable Daytona.
It took some effort to remove the rear tire nut, but I am satisfied with the soft touch and effectiveness.
Durability will be confirmed in the future.
View detail
Used on a 50cc 2Cycle moped. Quite bright!
I originally used M&H Mats Stripe Halogen bulb 12V35/30W Clear, which was brighter than OEM, but still old mopeds are still dark.
Since I use them for commuting, I decided to use LEDs for safety reasons.
Installation can be done simply by removing the headlight cowl.
The color is a beautiful White and the brightness feels 1.3 to 1.5 times brighter.
The white color is more like a recent vehicle than the yellow color, which makes it a better parenthesis.
I think it is a good cosmetic product because it is inexpensive and made by Mats Stripe, which is a reliable company!
I use it on my AF35LIVE DIOZX, but the Valve is PH7 because I replaced the Headlight with an external one.
View detail
Fits: YAMAHA JOG, HONDA monkey, HONDA Monkey Baja, HONDA Dio, HONDA CB500F, YAMAHA MINT, YAMAHA TZR50, YAMAHA TZR50R, YAMAHA TZM50R, YAMAHA JOG80, YAMAHA JOG-Z, YAMAHA JOG50 Sports, YAMAHA CHAMP80, YAMAHA CHAMP-RS50, YAMAHA CHAMP-CX, YAMAHA CHAMP, KAWASAKI KSR-II, YAMAHA ALLCHAMP, YAMAHA BWS, KAWASAKI KS-2
Cancellation.
I asked for it this morning and it is safely Cancelled. View detail
It's brighter than a white-hot bulb.
Installed on a Honda NSR80.
The NORMALWhite heat bulbs in the NSR80 were very dark, so we replaced them with LED bulbs to make nighttime driving somewhat safer.
If anything, it is not for the purpose of illuminating the road surface, I'm here, Appeal." I think it is highly satisfactory if you consider that LEDs for
In NSR80, the heat sink part of the Light case and LED Lamp is the contact limit. There is no problem.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Product # 1P2004
One of my friends has a rare YAMAHA Town Mate 6 volt motorcycle. He was faced with the problem of finding incandescent headlamps. We are very lucky that this product is available in the webike. The workmanship is good. Great price. View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Anyway, it's bright.
Used for GYRO CANOPY (TA03).
CANOPY is bright anyway, partly because it is a two-light system.
Light distribution is not bad.
Now we are hoping for durability.
View detail
Fits: HONDA DJ-1L, HONDA CABINA 50, HONDA GYRO CANOPY, HONDA GYRO CANOPY, HONDA BROAD50, HONDA DIO, HONDA DIOSR, HONDA G DASH, HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1RR, HONDA LEAD50, HONDA JOKER50, HONDA Giorno, HONDA TACT, SYM DD50, HONDA Live Dio Cesta, HONDA LIVE DIOZX, HONDA LIVE DIO ST, HONDA LIVE DIOSR
Clutch connection is also Smooth and usable without any problems.
After purchasing a GYRO CANOPY (TA03) with a mileage of 70,000 km, I checked the condition of the drivetrain and found that the clutch was in good condition.
The wear limit was exceeded, so we decided to use the for RepairClutch outer, OEM Center spring, also by KN Kikaku, and the
We replaced them at the same time.
The quality is comparable to OEM products and the price is reasonable.
Now we are hoping for durability.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
30W floating.
I have been using it for about a week.
Light is M&H Maz StripeB2 on DMR-JAPAN Multi-reflector used for about 2 years. [Color] Clear (35/36.5w) This is a change from
Direct AC compatible, so it is also compatible with KSR with half-wave rectification.
It blinks in Idling, but lights up normally when the rotation is up.
As for the depth in the Light, there seems to be room for about 5mm.
So far no discoloration deformation etc. of the Lens section, no thermal problems.
I feel it is brighter, but my impression is that it is too White for me and not easy to see.
I would replace it immediately if a VERSION with a lower color temperature is available. (4000-5000K)
Halogen → I floated about 30W with LEDs, so I will be able to increase my warming equipment for winter.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Bright!
The Halogen bulb was no longer working, so I decided to replace it anyway!
I had previously purchased an LED that claimed to be an "explosive light" on the Internet, but it was the exact opposite, being darker than the original and thus useless, so I wondered if this would be the same. I was a little bit nervous about purchasing it and installed it with Tokyo Do Reflector Light and some modifications, but I am happy to say that it is bright and has perfect visibility!
However, I need to note that the OEMGlass Lens Light of the old CUB I tried is not able to secure the Stroke of the LED Lamp - so I need to be careful!
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
The total length is long, so make sure to check in advance.
[How is it used?
The Headlight Bulb of the LITTLE CUB that was given to me was out of order, so I searched for a replacement bulb to brighten it up.
Was the one you received as per Image?
A little longer overall than I thought?" I felt that the LDE sphere is like that?
The product was generally in line with the Image.
How was your experience with it?
I immediately replaced the OEM bulbs and PonLEDs that had gone black due to bulb failure and checked the headlight from the front, and found that it was close to the lens side of the headlight (not hitting the Lens, but the Clearance was about 5mm).
I did the work without checking the Instruction Manual & notes on the back of the Package due to my bad habit, but the back of the Package has a *Not available for MONKEY, APE, and SUPER CUBSeries. (Electrically not compatible with FI (Injection) Spec. cars of these models. (Also, carburetor spec. cars cannot be installed due to their dimensions. It was firmly stated.
LITTLE CUB is Material:I wonder if it was possible to install the plastic Lens because it is thinner than the old SUPER CUB's Glass Lens. However, there is a possibility that the heat generated by the LED bulb may affect the Lens, so we would like to monitor the progress at our own risk (likewise, those who install the Lens should do so at their own risk).
I started the engine and checked the light...it was so bright that I felt sorry to compare it to the OEM (the battery is completely dead, so there is a slight flicker at low rpm...) I am looking forward to driving after the Restore.
[Points to note]
As mentioned above, there are some car models that cannot be installed (for electrical or physical reasons), so do not purchase without thinking, as I did, and make sure to confirm the installation beforehand.
How did it compare to other products?
As for the CUB, I only know the OEM Headlight Bulb and the PonLED (and the PonLED was cheaper than the P7noHalogen bulb), so I can't say too much about the large size, but it is wonderfully bright compared to the OEM lantern light.
However, I will have to continue to check the LEDs in the future, as they sometimes make it harder for my old eyes to see what is in front of me in the rain.
Other items that would be helpful
Point and hang of installation
No difficult wiring etc., and can be installed in the reverse order of how the OEM bulbs were removed.
Large is strong, and it's not difficult.
[ITEMS TO BUY TOGETHER
If you only need to replace the Headlight Bulb, this product alone is Large sturdy (you will need the right tools for the job), but if you also want to replace the Blinker and Dale, you should also purchase products that meet your requirements.
[Opinions and requests to Manufacturer
When it comes to Motorcycle light bulbs, I trust Mats Stripe.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
PONLED PONLED LED Bulb!
I bought this product after looking for a Type LED Bulb that I could simply replace the bulb with.
4.I used it for the headlight of ADDRESS V100 which was converted to 5-inches Bates Headlight. Since the tip of the LED Bulb touches the Lens surface of the headlight, I shaved the tip of the Valve a little and installed it to secure the Clearance.
There are no particular problems with brightness or installation, but it is necessary to pay attention to the size of the light case used and the overall length of the Valve, etc.
It is easy to convert to LEDs by simply replacing the Valve without any wiring work.
Incidentally, it is compatible with both DC and AC.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Cospa strongest
It is now so bright that it is dazzling.
Recommendation.
Commendation for commuting to work and school
View detail