It's probably for the best.

Everything is in balance.
There is no uncertainty whatsoever. View detail

License Plate bend prevention

Before I installed the License Plate Base, I used to catch my pants and bend them, but since I installed the License Plate Base, I haven't had any problems. View detail

Good but too expensive

Brake masterTank on the Front. [Color] I made it Smoke and so did Rear. [Color] I bought it to make Smoke.
The original bracket to prevent the cap from falling off has a gap between the top claw and the gap, so I bent the claw part down with pliers and attached it for the time being. It is ugly, so I'm going to keep it until I buy a dedicated one.
The appearance is less noticeable. [Color] I am satisfied with Smoke because there is no worry about yellowing, but I think it is too expensive. View detail

Simple is Best!

It is a perfect score because it was intended to reinforce the License Plate. 。
It is excellent in terms of strength, texture, and cosmetics.
It is not suitable for dress-up purposes, as it has almost no dress-up effect. View detail

Master cylinder cap

Changed from Green Light to Gold. View detail

Necessary and sufficient

Solidly made, thick and strong enough.
It is necessary and sufficient since it is installed for the purpose of preventing distortion and bending of the Number. View detail

this is one of the parts that required for 2013+ ZX6R steering damper bracket. these are the parts list for the bracket excluding the steering damper and bolts: BRACKET 11056-2308 BRACKET 11056-2315 WASHER 92200-0293 COLLAR,L=3.3 92152-0834 WASHER-PLAIN-SMALL,8MM 410AA0800 View detail

Number Protection

I installed it to prevent the Number from bending. So far, it works well because it does not bend when it hits.
Also, it's very heavy. View detail

this is one of the parts that required for 2013+ ZX6R steering damper bracket. these are the parts list for the bracket excluding the steering damper and bolts: BRACKET 11056-2308 BRACKET 11056-2315 WASHER 92200-0293 COLLAR,L=3.3 92152-0834 View detail

Exquisitely made

Beautifly made this wheel spindle is jewel like its so nicely finished, I'm delighted with it as it finishes off my new front end, it complements the high quality Ohlins forks, Dymag carbon wheels and Brembo brakes that I have chosen for my motorcycle restoration, It has the feeling of an expensive watch its so nicely made, Simple to install and a very high quality and expensive 22mm hex driver is included with the shaft, This Shaft is extremely good value in my opinion, i look forward to testing it when my build is finished, Perfectly packaged and the shipping from Japan was on time, I have also ordered the JB POWER rear axle shaft and the JB POWER swingarm pivot shaft, Webike is my favorite source for parts and accessories even though I am thousands of miles away in Ireland. View detail

SPEEDRAMaterial:Twill Weave Carbon glossy Drive chain guard

The installation was not particularly difficult and was done by replacing the OEM.:Twill Weave Carbon shiny and looks up, the shape is more rounded than OEMGuard. View detail

Genuine Puig Hi-Tech Racing Grips

These grips were purchased for a customer who wanted a little more bling on their bike. The copper colour was the one they wanted. Searching Webike and found these fairly easily and at a better cost than I could source locally. With a few other small parts already in my basket, I got all shipped with my chosen courier which is of course EMS. They just get the orders delivered fast and I mean fast. Thsi all arrived in 5 days from being shipped which you cannot argue about. The grips themselves came in the standard Puig packet/box and were also covered in bubble wrap to keep them safe. The colour is more true to a copper than I would say orange but as it happened, this worked perfectly with the colour scheme of the bike anyway, win win. I personally have never tried this style of grips but once fitted, they do feel alright. I have to say though, the finish and quality of these are absolutely awesome. Really good CNC work on them and the grip part is super grippy so no issue with slippage. The customer is very pleased so thanks Webike, nice one. View detail

For countermeasures against release defects and for dress-up

[How is it used?
I was looking for the cause of the whining noise from the H2. I found many articles saying that the clutch release was causing the problem, and among them there was an opinion that Babyface was better than OEM, so I bought it.


Was the one you received as per Image?
I was surprised that it was 2 times larger than OEM. I was surprised that it was larger than OEM, but I was glad that the matt Silver was better than Image.


Was the installation difficult?
Installation is very easy with silicon grease and air bleed technique. Also, depending on the year, a gasket may be required.

How was your experience with it?
The squeaking sound is gone and the clutch is a little lighter at the same time. It is very good.


[Included Parts:were they on?
Gasket for Banjo bolt came with it, which is good. Also, Sticker is good. (?' ?) There is no Gasket to assemble the Release to the body, so it is necessary to buy one depending on the type of car.

[Was there anything that disappointed you?
I wanted to buy a black one, but I was disappointed that only two colors, silver and gold, are available in the lineup. I hope that other colors will be available in the future. View detail

Black-headed Rivet

Used to fasten the Brake hose clamp to replace the Front Fender.
The head is Black, so it's nice and unobtrusive.
Washer3.5×8 will also be needed.
However, the cosmetics are OEM parts, so the cost is not so good. View detail

Hey!

Contact Person!
I thought I sent you an email telling you to Cancel! View detail

Useful for cold season commuting

[How is it used?
installed
Was the one you received as per Image?
Grip is Slim and good.
Was the installation difficult?
Left Side Grip is difficult to install. How do we get there?" I struggled with it for about 15 minutes. I hit it with a board and tapped it in with a plastic hammer, but the Motorcycle shop advised me not to do it as much as possible because it could be damaged.
How was your experience with it?
The product Single Body is warm, but it is even more effective if you use Knuckle guard, Cover, or other devices to protect it from the driving wind.
[Included Parts:were they on?
Everything was in place.
[Was there anything that disappointed you?
Sufficient performance is not a problem. View detail

It was the best Size for W800.

I replaced the previous Type, and the size seems to have changed. I thought it was Large and sturdy.
It was the best size, completely covering the front and rear tiers with the Center Stand hanging down.
Moreover, it was exquisite that the Limit did not stick to the ground.
The fabric seems to follow the fabric from the previous MODEL, so there seems to be no concern about waterproof and durability.
The sealing tape at the seams seems to be firm, but in the past I have handled it roughly and the tape almost peeled off, so I try to handle it carefully, especially when taking it on and off.
Also, the bike is used in a covered parking lot where there are gusty winds, and the side cover has been scratched when the cover flaps.
Nevertheless, Balance's performance and price, which provide long-term protection under the current conditions, are unparalleled in quality.
The lower part of the cover can be adjusted to a very narrow range, and the belt near the center can be securely fastened, so that flapping can be suppressed to some extent.
As described above, the basic functions as a Cover are perfect, and it is made to be less prone to defects.
The black fabric does not stand out, and the color-coded lock holes on the front and back are designed for ease of use and security.
The cover is well made and is useful as a cover with waterproof function, protection, strong fabric, durability, and security effect. View detail

Just fit

I installed it on the front fork protrusion (12mm) of Ducati 900SS. 17mm ball, so I matched it with KaEdia's AluminumHold modified KDR-M6S-1, and it was perfect. View detail

price-performance

The effectiveness is only slightly better than For Street, and the durability is not good.
5Quantity in 1Season:Set consumed.
I was attracted by the price and tried it, but as a result, it was not cosmetic considering the frequency of replacement and maintenance. View detail

Required for Northeast Number.

The grip is so thin and natural that you don't even notice it has been replaced. View detail