Reviews
Fits: YAMAHA YSR50, YAMAHA TDR50, YAMAHA Axis, YAMAHA JOG Zr, YAMAHA TZR50, YAMAHA TZR250, YAMAHA TZM50, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400, YAMAHA RZ125, YAMAHA RZ50, YAMAHA SDR, YAMAHA RD50, YAMAHA GT50, YAMAHA GT80, YAMAHA JOG, KAWASAKI KS-2, YAMAHA BW's, KAWASAKI KS-1
Slightly modified
Used for TW200 (2JL)
The coils were not in good shape during the restoration, so, well, it's an old bike, and I had to replace them.
The compatibility chart said it would work, but to be honest, it wasn't exactly a poncho.
I had to shave the edges of the plastic on the body, shave off the part where the frame meets the plastic, and sweat.
Maybe it's just my TW, but I managed to get it to work.
Performance Quality is fine.
View detail
Genuine DID 420NZ3 Gold Spare Chain Link
I do not really use these too often as they are basically one step up from a push bike chain anyway. But, it is always good to have them in stock just in case a customer needs one. I found this chain link by just searching through the DID inventory on Webike website. It was really easy to find so you should be just fine. I ordered a few other different chain links along with this as I do like options with spare links. All were shipped together and this saved some shipping cost. My order arrived in 5 days from being shipped. The chain link came in a nice sealed packet with all that is needed to refit. You do get a not seem to get the white grease packet in this size chain but that's ok, I have a lot of these anyway. The chain link is very well made, it also is in the gold colour so nice looking too and it is also embossed with the DID logo so you know it's genuine. Very happy with these small purchases and these will keep me going for future. Thank you Webike. View detail
Rear Sprocket purchased with tooth count change
Purchased to change the number of Chain pieces when changing the number of teeth on the Rear Sprocket. clip type is easy to adjust as it can be removed as many times as needed. View detail
Chain assembly
The chain was stretched, so I cut it and used it for reassembly.
Installation does not seem to be that difficult since it is a Clip.
View detail
Front sprocket 1 up
I purchased this to raise one front sprocket on my YB-1FOUR.
It's a very satisfactory Custom with a small Gold amount!
View detail
OEM Equivalent Product, cheaper than OEM
Used for LITTLE CUB.
The low beam ran out, and a short time later the high beam also ran out. I bought this one because it was an emergency situation and it was immediately available in stock. The standard is 25-1. The Pine Stripe part number is 1P2015.
The grade of the bulbs is also the same as the OEM, White Hot bulbs, not Halogen.
I also found HalogenType, but the price difference was about three times as much, so I decided to go with the cheaper version.
Replacement is Light rim bottom, Quantity:Pair (for Left and Right) Remove the screw on the Plus of the light rim and lift the light rim upward to remove it.
The Glass part is replaced while touching as little as possible. Time required:2 minutes.
It lit up with no problem. I am relieved. I don't know about the durability yet, but it is a long-established domestic product and I am sure there will be no problem.
View detail
Fits: YAMAHA YSR80, YAMAHA YSR50, YAMAHA YB-1, YAMAHA GT80, YAMAHA GT50, YAMAHA GR80, YAMAHA FT-1/FT-50 70-71, YAMAHA GR50, SUZUKI COLLEDA SPORT, SUZUKI GAG, SUZUKI RG50, SUZUKI EPO, SUZUKI RV50VANVAN, SUZUKI GT50, SUZUKI GS50
Valuable parts
This is a Repeat purchase. The material is a common steel sprocket, but the effect of 16 shifting is clearly visible. There is no machining as shown in the photo. View detail
Fits: HONDA CB125, HONDA CBX125, HONDA DJ-1, HONDA gyro canopy, HONDA TLR200, HONDA Super Cub 50, HONDA Lead 50, HONDA Lead 90, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125
Product # 1P2004
One of my friends has a rare YAMAHA Town Mate 6 volt motorcycle. He was faced with the problem of finding incandescent headlamps. We are very lucky that this product is available in the webike. The workmanship is good. Great price. View detail
Fits: YAMAHA YSR50, YAMAHA TDR50, YAMAHA Axis, YAMAHA JOG Zr, YAMAHA TZR50, YAMAHA TZR250, YAMAHA TZM50, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400, YAMAHA RZ125, YAMAHA RZ50, YAMAHA SDR, YAMAHA RD50, YAMAHA GT50, YAMAHA GT80, YAMAHA JOG, KAWASAKI KS-2, YAMAHA BW's, KAWASAKI KS-1
Idling is stable
[How is it used?
TZr250RS (3XV) The Idling of the Ignition coil was not very stable and the Piston ring was replaced.
Both OEM Parts and Uotani are expensive, but I was worried about the quality of Chinese products, so I chose this product.
Was the one you received as per Image?
It is quite Orange Body and Plug cord as shown in the picture.
The mounting bracket is only held in place by a screw and can be removed quickly.
Was the installation difficult?
Simply take the Mounting Hardware and replace it with the attached Ignition coil.
A plug cap is also required separately, but I used the NGK plug cap that was originally included.
The Right Side is just the right length for the cord, and the Left Side is too long as it is, so we cut it.
How was your experience with it?
Idling has stabilized considerably, although I have only been using it for a short time.
Both low and high RPMs have been used without problems.
I am satisfied with the resolution of the ailing area.
[Included Parts:were they on?
Plug cap is not included and must be purchased separately if needed.
And, of course, Quantity:1pc., so in 3XV, Quantity:2pc. Set purchase is required.
[Was there anything that disappointed you?
As others have mentioned, the Waterproof Cap is loose and the Ignition coil terminals are bare. (OEMs, too.) So Waterproofness is doubtful.
【Review】
Unstable Idling is now stable and comfortable.
It is a consumable item, and the price is not that high, so there is no harm in replacing it if you do not feel comfortable with the current situation.
View detail
Fits: YAMAHA MR50, YAMAHA GT50 Mini Training, YAMAHA DT50 (air-cooled), YAMAHA MR50, YAMAHA GT50 Mini Training, YAMAHA DT50 (air-cooled)
To Power up
The Engine Displacement VolumeUp definitely increased power, and I liked that it looked the same as NORMAL! View detail
Fits: YAMAHA MR50, YAMAHA POCKE, YAMAHA VOGEL, YAMAHA GT50, YAMAHA GR80, YAMAHA GR50, YAMAHA TY80, YAMAHA TY50, YAMAHA RD50, YAMAHA GT80
Products that are often in short supply
This product used to be cast aluminum, but now it is all aluminum billet. (Cut-out) It is
Perhaps this product is not manufactured by FOR JAPAN MODEL, but somewhere overseas. I don't know if it is because of Corona or the war, but it has been completely unavailable for the past few months, and I bought it when the supply finally resumed.
This lot may have been produced at a different factory, and while there are no problems with use, it is somewhat disappointing that the finished surface of the internal flow channel is rougher than before.
I don't think it will affect the performance, but if you are concerned, you can polish it yourself with Leutor's Paper flapetc.
View detail
Fits: SUZUKI GS50, YAMAHA YSR80, YAMAHA YSR50, YAMAHA YB-1, YAMAHA GT50, YAMAHA GT80, YAMAHA GR80, YAMAHA GR50, YAMAHA FT-1/FT-50 70-71, SUZUKI COLLEDA SPORT, SUZUKI GAG, SUZUKI EPO, SUZUKI RV50VANVAN, SUZUKI GT50, SUZUKI RG50
Replaced because of rattling.
I had purchased a Sprocket from a low-cost manufacturer and was using it, but I was concerned about rattling from the beginning of the purchase, so I switched to XAM, a reliable company.
The rattling has been beautifully fixed and I am very happy with the results.
The vehicle in which it was installed was a YSR80, and since it was too high-revving engine to be suitable for city driving, we dropped the number of pins by one.
We have abandoned the maximum speed, but the emphasis on acceleration has made city driving much easier.
View detail
Fits: YAMAHA DT50, YAMAHA FT-1/FT-50 70-71, YAMAHA GR50, YAMAHA GR80, YAMAHA GT50, YAMAHA GT80, YAMAHA RX50, YAMAHA YSR50, YAMAHA YSR80, YAMAHA CHAPPY, YAMAHA CHAPPY, YAMAHA CHAPPY
Looks good.
It was used to replace a sprocket on a YSR80 that had been depleted on one side.
I could have used a cheaper one, but I chose this one because I wanted it to look nice.
I am very pleased with the change after the replacement, even though the original was no good.
View detail
Fits: APRILIA GULLIVER50, APRILIA RALLY(AIRCOOL), APRILIA SCARABEO50, DERBI Antorcha・Coppa・Diablo, DERBI FDS・GTS・RD-2, DERBI GranPrix74, DERBI Hunter(D+A), DERBI Olimpica・Savanah・Start, DERBI Sport・Variant・Yumbo, DUCATI 1000MHRmille/S2mille, DUCATI 350XL PANTAH, DUCATI 500SL PANTAH, DUCATI 600SL PANTAH, DUCATI 600TL, DUCATI 650SL PANTAH, DUCATI 750SS IMOLA, DUCATI 750SS, DUCATI 750SS, DUCATI 900MHR, DUCATI 900S2
Powerful and reliable iridium spark plug
Fits: SUZUKI GS50, KAWASAKI KSR-2, SUZUKI GT50, KAWASAKI KSR110, SUZUKI RG50, KAWASAKI KSR-1, KAWASAKI AR50/S, KAWASAKI AR80, KAWASAKI KLX110, KAWASAKI KLX110, SUZUKI RG50γ, SUZUKI RV50VANVAN, SUZUKI TS50HUSTLER, SUZUKI EPO, SUZUKI GAG, SUZUKI COLLEDA SPORT, SUZUKI GN50
I am going to use it for dress-up as well.
I used it on my Gamma Restore. I was looking for something that would fit my old car, and I was satisfied with the GOOSE I used before, so I decided to use it this time too. View detail
Fits: YAMAHA YSR80, YAMAHA YSR50, YAMAHA YB-1, YAMAHA GT80, YAMAHA GT50, YAMAHA GR80, YAMAHA FT-1/FT-50 70-71, YAMAHA GR50, SUZUKI COLLEDA SPORT, SUZUKI GAG, SUZUKI RG50, SUZUKI EPO, SUZUKI RV50VANVAN, SUZUKI GT50, SUZUKI GS50
Thanks for old car compatible parts
I bought this product for my 80? GAG, and the effect of FrontSprocket is very large, and the speed is clearly different after changing the size. However, since the clutch is NORMAL, it tends to slip easily. I am very thankful that the new one was sold. View detail
Fits: YAMAHA VOGEL, YAMAHA POCKE, SUZUKI BIRDIE 50 (2Cycle), SUZUKI COLLEDA SPORT, YAMAHA YSR50, YAMAHA YB50, SUZUKI BIRDIE 50 (4Cycle), SUZUKI BIRDIE80 (2Cycle), SUZUKI GN50, YAMAHA GT50, YAMAHA MR50, YAMAHA RD50, SUZUKI COLLEDA SCRAMBLER, SUZUKI GAG, SUZUKI COLLEDAK50, SUZUKI BIRDIE 50 (2Cycle), YAMAHA YB-1, SUZUKI GS50
No different from OEM Product
I used OEM Product because it was missing and I had no other choice.
Very nice product
I have been able to use it with no problems at all.
There is no strange slipping away.
Recommended
View detail
Fits: YAMAHA VOGEL, YAMAHA POCKE, SUZUKI BIRDIE 50 (2Cycle), SUZUKI COLLEDA SPORT, YAMAHA YSR50, YAMAHA YB50, SUZUKI BIRDIE 50 (4Cycle), SUZUKI BIRDIE80 (2Cycle), SUZUKI GN50, YAMAHA GT50, YAMAHA MR50, YAMAHA RD50, SUZUKI COLLEDA SCRAMBLER, SUZUKI GAG, SUZUKI COLLEDAK50, SUZUKI BIRDIE 50 (2Cycle), YAMAHA YB-1, SUZUKI GS50
OEM Product is the same etc.
Since it is an older Motorcycle, the OEM Product is discontinued, and I have no other choice,
The price is low and comparable to OEM products.
Installation, feel, and durability are no different from OEM products.
View detail
Fits: HONDA CB125, HONDA CBX125, HONDA TLR200, PGO MyBuBu125, SUZUKI K90, SUZUKI street magic, SUZUKI birdie, SYM fighter150, YAMAHA Cygnus, YAMAHA Cygnus, YAMAHA jog, YAMAHA jog sports, HONDA CBR125, KYMCO SOONER100, HONDA WAVE125, HONDA NSR50, HONDA NSR80, HONDA Super Cub 50, HONDA Super Cub 90, HONDA monkey
Normal is best
It is a standard product that is neither too much nor too little, and can be used with confidence. I haven't tried it yet, but when I replace the Valve, I almost always use this Valve. View detail
Fits: YAMAHA YSR50, YAMAHA TDR50, YAMAHA Axis, YAMAHA JOG Zr, YAMAHA TZR50, YAMAHA TZR250, YAMAHA TZM50, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400, YAMAHA RZ125, YAMAHA RZ50, YAMAHA SDR, YAMAHA RD50, YAMAHA GT50, YAMAHA GT80, YAMAHA JOG, KAWASAKI KS-2, YAMAHA BW's, KAWASAKI KS-1
It changes quite a bit.
Used for YSR80.
As for the effects, first of all, Spark is clearly stronger.
Since the CDI was also changed at the same time, it may be a synergistic effect, but I feel that the Torque has become thicker overall from low speed to high speed range.
Personally, I'm very happy with it.
View detail