Reviews
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
The price is a little too high
Basically, I don't ride on a rainy day, but when I passed the place where water is being sprayed by construction, it was a horrible accident So I installed it
The intuition with the Fender was perfect, but the treatment of the end surface is quite rough Because the double-sided tape which comes with is too shabby, it is not possible to use the Nitto No. which I have on hand I replaced it with 577
I've noticed that many people seem to be installing it with just Double-sided Tape I also used the 2 included pins to prevent the situation where they were missing (4 Pin is attached.) It may be that Double-sided Tape was a thick type, but The pins were not long enough to stop properly, so I welded them together with a soldering iron
I haven't run in the water yet, but the effect is quite promising based on the position of the Tire That's right
I think the price is a bit too high, including the detail work
View detail
Fits: HONDA CBR1000RR Fireblade, HONDA VFR800F, HONDA VFR800X Crossrunner
The width was somewhat missing
It installed in VFR 800F.
Remove Front Fender from the vehicle and remove the supplied Double-sided Tape and install the product.
After that, 4 holes are opened at 4 places and the attached Pin is inserted and completed.
(Fixing with Double-sided Tape alone is uneasy)
However, because the width is slightly smaller than Front Fender, I feel that I pulled it with fixed Pin..
Although it does not understand to the appearance, ....
I think that it seems high if I think of them, but the person who was there is more muddy the condition changes.
View detail
Fits: HONDA CB1000, HONDA CBF1000 FA, HONDA CB1300
It was good not to be conspicuous.
(What made you decide the purchase?)
I joined a certain Events the other day and got pouring rain on the way home, raining from the top of the Engine to the inside of Cowl, struggling to clean up and clean up. Also, as muddy sticks, I will spoil the preciously polished Exhaust pipe, so I bought it with reference to the other reviewers.
(How was it actually used?)
I still can not say because I am not running, but 15 centimeters has been longer than OEMFender, so my expectation is Large.
【Was it difficult to install? (Hard parts case)】
Ultra Strong Double-Sided Tape for installing the exterior parts of the car was abundant because there were only a few Double-sided Tape which was originally attached, so I tried installing it in detail.
【Please tell me the point of installation and hang (in the case of Hard parts)】
The Ultra Strong Double-Sided Tape I wrote earlier was too strong, trying to position it, even if I tried to peel off, I could not peel off well and it was slightly misaligned. Let's say good because you do not have to worry about peeling while running.
In Instruction Manual, it is better to remove Fender and not to say that it is not written. Screw attached to Front fork, Quantity : Pair (for Left and Right) It is easy because it only removes a total of 4. It is necessary to pay attention not to add Wound only when pulling out and putting it.
[Is there anything I was disappointed about?]
I wanted you to attach a double-sided tape a little more. It happened because it happened to have a Double-sided Tape, but it was a place I had to go to buy.
【Hope for Manufacturer ? Please let me know if there are any improvement points]
Increasing Double-sided Tape, it's still a price. Because there was a point, there are a lot of people who have flown into purchasing, so I expect in the future.
【Have you compared items?】
I can not find it in particular..
View detail
Fits: KAWASAKI Z1000, KAWASAKI Z800E, KAWASAKI Z800, KAWASAKI Ninja1000 (Z1000SX, KAWASAKI Z1000 R, KAWASAKI ZX10-R, KAWASAKI ZX6-R
Function-oriented than texture
As the mud to the Radiator is bad at the time of running on a wet road, if you extend the Front fender you think that it will be a little better..
"Texture"
It's just black material, not so good. It is also a place that I can not see much from the outside, and since Front fender itself is black color, I do not care much about it.
"Mounting"
1. Front fender desorption (Because it is easy to work)
Brake hose clamp about Fender part is disturbing, hard to detach.
2. Since the installation accuracy interferes a little with the Rivet part of Brake hose clamp inside the Fender, I cut away the extender to be attached with Cutter about 2 mm. Then Just fit.
3. Standard Double-sided Tape is too cheap for installation, so we added a commercially available Strong Double-sided Tape. Mounting with Fender Degrease the Extender with PearlCleaner, warm it with Dryer and paste it.
4. It seemed that there was no problem with Double-sided Tape alone, but fixed in the attached Pin. (Drill with 2 mm Drill)
Although the product is an impression that it is a little expensive from Material and texture, I am generally satisfied.
View detail
Because I can not make it myself
Right and Left 's Curve is indeed
Not the same, One Side was a short product. Probably not enough to change the Gold type budget
Microfabricated workshop (It is not a factory or a company) Is it made of.
It seems not a problem of finishing after molding.
So it is impossible to ask for quality improvement.
If you make the same thing individually, if you have time, materials and techniques you can make it in 500
Let's stop it.. 5000 I bought it because it is safe and I can complain.
There is nothing problem with the installation state. Be familiar with the fans beautifully.
It is a feeling that the mud bounced by Engine by about 60%.
I installed it securely in three locations with Double-sided Tape and Screw stopper.
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
I think it is effective
I felt uneasy with the attached Double-sided Tape so I added about 2 columns and installed it.
I think that the jump of the puddle has been alleviated.
Color : Because it is Unpainted and a simple shape it may be nice if it is a bit cheaper.
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
Maybe there is effect
It was attached to NC 700X, but this time it was installed in 750S. Attached with the attached double-sided tape and drilled in three places of the OEM Fender and bound with the attached resin Pin was made according to the Manufacturer designation, when it was 700 ×, it was as it was, but because this time it is troublesome to drill, Cemedine SUPERX I glue it with. There is nothing wrong with fixing.
Since I installed it at the same time as purchasing a new car, I can not compare the effects because I can not say anything, but NC's OEM Front Fender is very short, so I think there is an effect. Delivery The car was running for 500 km continuously on an expressway on an early rain, but Under Cowl was dirty, but the upper part of Cylinder head and Radiator did not get dirty.
View detail
Fits: YAMAHA Tracer 900 GT, YAMAHA MT-09 Tracer, YAMAHA MT-09 SP, YAMAHA MT-09
Is good!
With this and nothing, the degree of water stain to Engine, Radiator changes dramatically.
The appearance is extended Length and Color, because the texture is consistent, it is delicate ...
It is the best performance.
I used it with MT - 09 but it was useful as it was lost to the Radiator.
View detail
Extension of mudguard @ GROM
【What made you decide the purchase?】 Because I got cheaper than usual in Campaign.
【How was it actually used?】 Sufficient, functioned as mudguard.
【Was it difficult to install? (Hard parts case)】 I can not use the included Double-sided Tape, attached my own ButylTape and attached it.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Clean the adhesive surface.
[Is there anything I was disappointed about?] A little making is sweet
【Hope for Manufacturer - Please tell me if there are any improvement points】 None
【Have you compared items?】 Required
[Others] Any
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
I received it immediately after placing an order
Second order, second worked and Rear Fender batched
Hidden in Side Back and finish of ordinary feeling
Because it is an invisible place, it stops even with Small Tapping Tapping screw and it has fall prevention
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
Very good
ExactlyFit Installation was easy.
Just by increasing the Double-sided Tape, I floated the floating part so that the splashed muddy water did not hang on the table with Coking.
Anyway it's easy
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
Need for self-processing
The shape was Exactly to the OEM Front Fender, but the texture of the material and color of the commodity did not match the price very much.
Daiso's Material : Carbon Style Imtechan at the inte Rear seat, Double - sided Tape also dropped Body 's grease and replaced it with 3 M Strong Double - sided Tape.
Evaluation of Cost performance will definitely be one star.
View detail
Fits: YAMAHA Tracer 900 GT, YAMAHA MT-09 Tracer, YAMAHA MT-09 SP, YAMAHA MT-09
I think that it was good to install
Since attachment is not solely with the included Double-sided Tape, we attached a double-sided tape separately and attached Pin attached.
Drilling is necessary to install Pin, but it is troublesome to measure curved objects.
I also have holes in Fender, so it will be ugly if I do it.
There is no problem with quality and texture, but it is awkward for price.
The shape is perfect for Fender of Racer. Since colors are almost the same, there is no discomfort.
I think that the price is high for the thing, but when thinking of the clogging of the Radiator, the belly can not be changed on the back.
Although it is currently in use, as soon as it gets installed it will not rain so I do not know the effect in rainy weather, but I think that winding up to the Radiator such as Small stone and sand has been relaxed considerably.
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
It is as good as your rating
It is a little expensive and can only be taken out of Seal, so we need ingenuity to install. I installed your review as reference. It's only durability after. View detail
Quality is too low for price
Quantity : Pair (for Left and Right) It was disappointing in terms of quality, such as the different Length of the edge. Is it a defective item?
It's easy to install because it is stuck with Double-sided Tape, but I added it myself because I am anxious only with the attached Double-sided Tape. Screwetc. It does not come.
In the case of BOLT Shoulder Bag, since the Fender is about 12 Length extended, I think that the effect of preventing mud bouncing is high, but at first glance Quantity : Pair (for Left and Right) I am concerned that the Length of the edge is different, and I will make it a low evaluation.
View detail
Dirt has decreased
In the OEM Shape, water is added to Oil cooler (Muddy) I got it because the sand stain is outstanding.
I installed P & A Fender and I ran on a wet road, but much water (Muddy) It seems that it was resolved. After traveling Oil cooler shows clearly few traces of splash. If Fender gets a little longer shape it will be more effective, but thinking of the overall Balance is Limit.
I did the installation myself. Although Double - sided Tape had already been affixed to three places, in the manual there was a statement recommending the use of attached Screw so we stopped Screw without hesitation. Reliable feeling is different.
Screw attached 4, resistant to opening a lot of holes, opened by three individual holes at the discretion of the double-sided Tape and Screw installed in combination. I ran a few hundred kilometers, but it seems that there are no problems in three places. Work was not taken so much as it was only removing and attaching Fender, drilling with Drill and installation.
The reason why Cost performance is low is that the price is too high "☆ 3" I succeeded.
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
There seems to be little mud to Radiator.
I removed the Front fender, opened the hole and installed it.
It will be absolutely out of with Double-sided Tape alone.
I can do it myself but somehow I got it to Motorcycle shop.
Thinking of labor costs you can do it by yourself while you can do it by yourself.
I think that it is effective because there is little mud to the Radiator.
If it is painted in the same color as Fender it may not be noticeable.
View detail
Function, shape, passed together
I was reviewing the Radiator core guard, but first purchased without mud and stone splash.
From the conclusion the effect is absolutely Large! It will rain, even with some puddles the Radiator will not get dirty.
I am Double-sided Tape reinforced, but there is no blur, dropout.
Somewhat, there is a gap in close contact with Fender, is it a problem of pasting,
The shape does not feel uncomfortable, as time goes by, the feeling that it was attached from the beginning.
For a while the purchase of Core guard is gone.
View detail
Future expectation
Purchase to prevent contamination of Exhaust pipe part. It is something to worry about because Fender and Tire 's Clearance is narrowed because it is set inside Fender. Machining was done by Motorcycle shop and we had a hole drilling done. Because there is some gap in the overlapping part of Fender, we do not recommend it for those who want precision.
I am satisfied so much if I think about the Universal Product level.
View detail
Water countermeasures
As it is NORMAL, there are quite a few of the water splashes, so I bought it as a countermeasure.
Kit was attached with Puri Rivet and Double-sided Tape, but it is fixed with Epoxy adhesive and Aluminum Rivets because it is prevented from dropping out.
The water splash that had been flying to near the Top Bridge was considerably reduced.
View detail