Reviews
Simple and universal to use!
I cut and attached it to match the SV650X's knee grip position.
I made a mold at random and cut it with Cutter & Scissors, so it didn't look pretty, but it's acceptable.
I put it on when it was around 10 degrees Celsius, so I warmed it up with Dryer beforehand and it bonded normally.
The fit when gripping the knee is good, and the grips are tight without slipping.
Necessary and sufficient
View detail
cheap but quite good
I use Kijima tank pad on my Honda VFR800 VTEC gen 6 2003. Kijima tank pad is a bit cheap, small size but quite good. I think it fits very well. View detail
very good
This is a definite product, and when it comes to Tank Pad, this is the only one I would choose! View detail
Highest Universal
Used in Circuit.
It is a highly universal product that can be fitted to any tank.
View detail
Required for Mini bike
There is a subtle bump on the side of the Tank on the Z125pro.
I was wondering if there is anything we can do about the interference with the Pants knee pad? I was wondering if there was any way to fix it.
I tried to temporarily attach it, but this time I was concerned about the difference between the pad and rubber of the Moto pan.
As a result, the KIJIMA Tank Pad is used for the rearmost to forward phases of the Tank, and the
10mm thick Neoprene rubber (Foam Rubber) was spliced and extended.
This eliminates the problem of lateral knee movement during the Corner ring.
As for the seam, I guess it can't be helped that the escape of pasting on the curved surface is removed and that it is not visible while driving.
Eventually, it's going to be in the joints. Stripe" But I'll put it in and dress-up.
View detail
Necessary and sufficient.
The smallest material, size and shape necessary to prevent tank damage.
It may be valuable in a world of excessive and flashy Tank Pad. It is also inexpensive.
This is the third time I have purchased this product, and while it is easy to apply, it is a challenge to remove the old one.
Although the work was done in the summer, the urethane portion deteriorated and could not be removed all at once.
It's a Fuel Tank, so it can't be heated with a heat gun.
To avoid scratching, Plexus is soaked into the urethane part and carefully stripped off, and then the urethane is removed.
Paste residue was removed with Silicon-off.
It is better to cure the Urethane so that no pieces of Urethane fall into the Air cleaner.
If it is immediately after a new one is applied, it is relatively easy to reapply (peel off).
The picture on the Product Page is old and hard to understand, so I'll post a picture.
View detail
This Type fits the old car.
Various types of Tank Pad are sold, but this type is suitable for LaserReplicaType of 90's. Because it is long, you need to be careful not to bend it when you stick it. If you fail, you can't remove it because the adhesive is strong. View detail
Recommendations for old cars
NAKED and Recommendation to old cars that should not be messed up.
It's not nearly as thick as it should be, but it sticks and it works.
When you put it on, you should degrease it properly, and it might be good to warm up the adhesive side with Dryer etc.
View detail
It's a little small
Large size is about 120mm×80mm
The basic shape and cutting is beautiful, and it fits all kinds of cars, especially old cars
But this one is a bit pricey at $800
View detail
It is safe.
You can use it any way you want because it's designed to fit any motorcycle
It's a little small I'm not sure if you can get another large
The price is high for that
View detail
I like this kind of thing
I bought it a long time ago as I had it on my CBR, but it's now on my motorcycle I cut and pasted only the middle one because it didn't fit the shape of the tank somehow There may be many people who think it doesn't look good, but I like this kind of design
It's been a few years since it was installed and the powder has started to fall off due to deterioration, so I'm thinking it's time to replace it
View detail
There's nothing fancy about it...that's what's nice about it, simple is the best
One of the problems that plagues me with Motorcycle "Tank Pad Isn't it?
I always try to wear it, but it really bothers me..
My points of choice are Design and Flexibility
[Design]
GizaGiza products, crispy products, wacky prints and more! But I still think the most important thing is "I'm not going to break a Motorcycle Image, This is the only way
Any other embellishment could be a snake in KATANA's detailed and sophisticated design! (Laughs) (Laughs)
This product is perfect in that regard No claims!
He is a shadowy workhorse who protects Tank quietly and discreetly with texture
[Flexibility]
The unexpected foreshadowing in choosing a Tank Pad is "The shape of the tank, the curved surface It is
Not only KATANA, but also the HORNET, which I used to ride before, the curved surface of the TANK is front and rear Quantity:Pair (for Left and Right) Depending on the pad, some of them do not follow the shape of the pad well and some of them float, and some of them have a hard time adhering to the steeply curved surface There was a problem with the lack of
This product is perfect in that regard Very flexible!
Sponge rubber with adhesive Seat...Flexible, light and quite strong adhesion So, to the extreme "T I don't think it's a problem to follow a curved surface like this
[Durability]
At first I'm not sure if it's this soft or if it's large and strong.. I was not without the thought that I would be able to use it (I also bought a spare), but surprisingly, after three years of use, it cracked and There was no chipping or other deterioration
It depends on the environment, but I think it's very reliable
【Review】
In the motorcycle industry, where custom parts that stand out in a flashy way are preferred, the It's that rare entity that dares to be inconspicuous and enhances its value
To be honest, I think the price tag is quite high when you consider the cost of raw materials and other factors, but as a one-of-a-kind I hope this product will continue to exist
View detail
As long as you don't make a mistake the first time, you're good to go
The tank is slippery and round, and I have been dissatisfied with the knee grip in the mountains and in the circuit I bought it because it was there
It's a 90s Motorcycle so it doesn't look that different I cut the edge of the bike, but it's not easy to cut with Scissors because it's stuck on the adhesive part Notes It's been almost half a year since I put it on, and I've driven in the rain a few times, but the adhesive strength does not decrease However, I need to find a way to prevent dust and sand from accumulating in the gaps between the attached surfaces It might be a good idea
View detail
The usual Quantity:1pc.
CBR600RR GymkhanaSpec.
TZM50R
Used in
[Feeling of use]
outstanding
If you're a slalom guy and you haven't done anything with your knee grip yet, you should!
To ensure that the thin, truthtool sliding tank of the mini bike can be hooked up with one leg becomes
【Cospa】
The best
I didn't think it could get any better than this
There is another Manufacturer's thin type, but it's not very durable and it can be punctured quickly No recommendation
【attachment】
Cut with Scissors or Cutters to the shape you want to paste
stick
that's all
If you want to get a little obsessive, you can use pattern paper
It's a pretty strong adhesive, so if it's on a painted surface, it won't come off easily unless you melt it with something, so that's all there is to it attention (e.g. to detail)
I mean, you don't Gap while you're driving
[Looks]
It's just a sturdy Sponge sticker, so it's neat! () If you're looking for a good motorcycle, this may not be for you
It's going to deteriorate over time and look a little worse for wear
View detail
It became moderately Cushion and Knee grip and Hold improved.
When straddling, it became moderately Cushion and Knee grip and Hold well also well with older Motorcycle like vfr 400 View detail
It is Repeat.
As for Racer replica, this type is still.
I am using T type.
Riders Zipper is also Large durable.
I am exchanging it because it is a consumable item as it gets damaged.
View detail
I am very satisfied.
Shaped around the thigh part, even if you lie down on the tank, the height where Wound does not stick, the material like Wet suit is thick, so cushioning is also good and good parts not in other Pads were realized at low price I think that it is an excellent product.
Visual may not be very good because it gives priority to functions if given strong.
View detail
Small Sai
The function as Pad is very good, but I'm sorry I'm Small. In Tank's Large Motorcycle, the part where Pad is effective is the crotch part, and it does not cover to a place easy to attach Wound to Tank, such as Jacket's Fastener part. View detail
Standard classic from over 20 years ago
It is particularly suited to the old Motorcycle.
Looking at the Replica in the 1990s, you often have KIJIMA's Tank Pad.
Before attaching it, it was a Universal Centipede like Pad
After all, when you did not attach anything beside Tank, it was slippery at the time of Knee grip.
This covers the stomach hit area + the thigh sandwiched between covers so it is recommended not to worry about the shape.
I adhere it with Double-sided Tape, but I think that it is better to go carefully when this Double-sided Tape is quite powerful and stuck.
About 1 week after I started using it, I had a feeling of incongruity at the time of Knee grip, but I think it is due to the thickness of this Pad.
About half a month later I ceased to worry.
Just wearing a white series Pants or a jacket, I rub on Pad and I will watch a little black, so be careful.
Just rubbing instead of color transfer seems to have just adhered Urethane, so it turned out beautiful if you choose it.
View detail
In order to raise a feeling of a Hold in the WEBIKE Monitor Tank, in the center, Cut was carried out and right and left were stuck. Since Position change was made according to how depending on which he rides since cutting is also ea
In order to raise a feeling of a Hold in the WEBIKE Monitor
Tank, in the center,
Cut was carried out and right and left were stuck.
Since
Position change was made according to how depending on which he rides since
cutting is also easy, it was saved.
View detail