KIJIMA Stainless Steel Exhaust Band

I used to use a different band, but when I tightened it, the bolt diameter was a little thin and it was not strong enough.
After a certain amount of use, it was easy for the screws to be ruined by heat and tightening.
This Band has a slightly thicker Bolt and has no strength problems, so this Band is now used. View detail

Note to Size.

It is just an Exhaust Band.
Purchased this CB400SF nc42 2016SPMODEL OEM Exhaust Band because I lost it.
Band is Stainless Steel, but Bolt is Steel.

One sizeSmaller than this, the company's Exhaust Band just barely didn't fit and I had to buy a new one.
The π diameter or measurements are rather strictly made, so it is recommended that you measure your measurements before purchasing! View detail

Used for I.D. 60.5Φ.

63-68mmSize is used for Exhaust System with inner diameter of 60.5Φ.
Looking at the cost of Bolt's surplus, it would have been better if it had been a little smaller.
However, there is no problem at all in fixing it, so I am satisfied. View detail

Material:Stainless Steel is good

I made a mistake with the size, but I think it is a very good product, Stainless Steel and it won't rust, and considering the burning thing, it is a Material:Stainless Steel exhaust pipe and silencer with band and material:Stainless Steel is a good choice. View detail

Used in SR400

Material:The exhaust pipe and silencer are made of Stainless Steel, so the color of the Plating Exhaust Band is different from the Plating Exhaust Band, but the Material:If the band is made of Stainless Steel, the burnt color will look natural. View detail

easy to get

When I installed YOSHIMURA's Slip-on Silencer, I am a stocky person, and I broke the attached Clamp band by holding the Torque wrench too tight for some reason, perhaps because of the installation angle.
It takes time, but I looked on the Net to order from YOSHIMURA and found that KIJIMA's products are identical to YOSHIMURA's.
It was easy to obtain and inexpensive. View detail

I bought it as a spare.

I bought this as a spare for the Exhaust System that came with it.

I think this one is easier to use. View detail

Silencer Fixed

I purchased this product for my car car Silencer-less Toa. It works fine. It can be fixed tightly. View detail

It was Exactly for Repair of CB1100Normal muffler!

Normal mufflerBand was ruined by Rust, so I replaced it. The price is low, so it helps.
This product has a Band section with Material:The screw is made of Stainless Steel, so its strength and durability are assured. View detail

It's safe to say we're a trusted Manufacturer!

When I installed the exhaust system of YOSHIMURA, the clearance of the included exhaust band was limited and it was not easy to work with, so I bought a larger one.
I used the Bolt that was included in the Exhaust System because it seemed to hit the Swing Arm. View detail

The Bolt is Steel, which is −?

When I replaced the Silencer with Other Brand Product, the Bolt of the attached Band that tightens the Exhaust pipe and Silencer was too long.
The Band is made of Stainless Steel, but the Bolt is made of Steel. View detail

Mostly OK.

It is used for the Joint of Slip-on Silencer.
I have purchased and am using it because it is wider and can be hung more tightening torque than the OEM.
If you want to say it, I think the follow-up performance will be 100% if you don't have the R-shaped inner gold part of the Bolt tightening part. View detail

kijimaKIJIMA Stainless Steel Exhaust Band

The other day, I bought an Exhaust System and squeezed this product
I bought it. Actually, I installed,
I could install without exhaust leaks.
I think that it is better to tighten it quite tight when tightening the Band.
Also, in case it becomes necessary, you must make this product
I wanted to use it. View detail

Exchange from Super trap's OEMBand

It is an exchange from OEMBand of Super trap.
The reason is that Bolt of OEMBand is Inch size.
Since the approximate value is 11 mm, it was tightened with 11 mm Box wrench, but workability is bad
Since the quality of Band itself was also questionable, I made it to Band of KIJIMA.
Improve quality by reducing the width of two sides to millimeters. It is tightened to Smooth. I'm glad I bought it.
By the way, painting Thread compound makes Smooth and rust prevention.

Other companies also have similar cheap Band, but because the board around Large Bolt is omitted
I am a cigar. If you tighten it strongly, distort the Pipe
We do not recommend as there is a possibility. View detail

Exhaust Band of good texture

When exchanging from the OEM to the second-hand external exhaust system, since we did not have enough Exhaust Band, we installed this item.
When opening the product and taking it in my hand, I received a heavy, heavy and heavy impression. You can see that it is quite sturdy. When actually installed, I could tightly tighten it so I am satisfied with Large. View detail

Satisfied with both quality and price

I used it when installing an external Slip-on Silencer.
Unfortunately Size did not suit, but the product itself was sturdy and texture was good.
I'd like to purchase another Size's item. View detail

Bolt is Steel (iron) is.

Replacement as the mounting became rusty and rusty.
Exhaust System Included Parts before replacement : Same as Body, Body is SUS, Bolt is Steel.
Maintenance (Anti rust) If you do not do it probably is the same fate.
I wonder if SUSBolt can not do it ~ I'm sorry. View detail

Muffler bands are also exchanged at the same time as it changed the Muffler. . Since the rust of the attaching-at time of exchange Band was severe, it was felt refreshed. engine performance is a very ordinary Band.

Muffler bands are also exchanged at the same time as it changed the Muffler. . Since the rust of the attaching-at time of
exchange Band was severe, it was felt refreshed.
engine performance is a very ordinary Band. View detail

It is used for the 2.5-inch Silencer of KERKER. Since the rate of Silencer opening was shallow and there was wall thickness [ a rate ], the Screw of the Band was licked and welding had separated. This Muffler band is strong also at . It was abl

It is used for the 2.5-inch Silencer of KERKER. Since the rate of
Silencer opening was shallow and there was wall thickness [ a rate ], the Screw of the Band was licked and welding had separated. This Muffler band is strong also at
. It was able to fix thoroughly. Satisfactory. View detail

It was changed simultaneously with exchange of a slip-on muffler. The genuine band which was being used from the first has severe rust of a bolting screw position and if it was used much, it was indispensable to exchange of a screw or rust picking. When

It was changed simultaneously with exchange of a slip-on muffler. The genuine band which was being used from the first has severe rust of a bolting screw position and if it was used much, it was indispensable to exchange of a screw or rust picking. When I was searching something that may be not rust easily, since it is in the place which eyes do not reach easily usually, I found this product and purchased in this price. Although corrosiveness-proof was not found yet, looks became smart compared with genuine. I think that it is 5 stars if corrosiveness is clear. View detail