Items required when adding a Tank to MASTER

[How is it used?
I use it for Touring and city driving.
Was the one you received as per Image?
It was just like the Image. The quality is high.
Was the installation difficult?
It was easy to install with the included Screw.
How was your experience with it?
The Tank is firmly fixed and robust.
[Included Parts:were they on?
It was attached.
[Was there anything that disappointed you?
There is none View detail

Looks good

The stuff is good, but a little expensive!
It is good for those who want to have it in GALE SPEED. View detail

Inexpensive and easy to install

I bought it to use with the brembo s50 large oil cup. The installation angle needs to be adjusted by myself, otherwise it will be inclined. It is not suitable to install the original thick gasket when used with the s50 oil cup. The thick gasket will cause insufficient space for tightening the nut at the bottom. It is recommended to use a thin gasket for installation. There is nothing to say about the appearance. Generally speaking, it is a Nice product, simple and easy to install. -------------------------------------------------- -------- I used it to use it with the Brembo S50 oil cup. The installation angle needs to be adjusted by itself, otherwise it will be tilted. It is not suitable for installing the original factory with the use of the original factory with the S50 oil cup. The thick pads will cause insufficient space to tighten the nut at the bottom. It is recommended to use a thin pad. Good products, simple and easy to install. Powered by Google Translator View detail

Texture is good.

Purchased when GALE SPEED's Brake master was replaced.
I put a Washer on my Separate handle because the bottom of the tank hits my Separate handle.

The quality is perfect, but I think the price is too high. View detail

It breaks easily.

It breaks easily.
It breaks easily.
It breaks easily. View detail

Don't turn off the We-Big! It breaks easily.

I write imprements and they erase them!
Collusion? If you're going to erase bad reviews, don't ask for imprements in the first place!

It breaks easily.
I bought two of them and both broke right away.
Even if you contact Manufacturer "Body issues." He said.

Bad item and bad response! View detail

It breaks easily.

It breaks easily.
I contacted Manufacturer and they said it was a problem with the car body.
Poor product and poor response. View detail

Useless.

Gail's Radipon (both Brake and Clutch) Purchase at the same time as
Ruptured in less than 2 years!
I bought the same one without Objection processing etc., thinking I had accidentally pulled a HaGap, but it broke again in a year and a half!
Contact Active, but It's not a good match for the body of the vehicle." He said that it was the responsibility of the buyer.
If it's a big single, but if it breaks in a parallel 4-cylinder, it's not for sale, is it?
I will never buy again, nor will I buy Active products. I will use a different Manufacturer's product for my current one as it is updated.
No trust in Active products! View detail

for Clutch Master.

I bought these to go with Gail's Clutch master.
There was a Plate type that was a little cheaper, but I dismissed it because it looked like a Bracket from Home center and bought this one that was on a top ranking.
It can be attached to the Mirror Holder.
The texture is elegant and not bad.
The only drawback is that the angle of the Clutch lever is not adjustable, so the Master tank may lean a bit depending on your preference.
And I wish I had Black instead of Plating if possible! View detail

I wanted Black.

I bought this to go with Gail's Brake master.
There was a Plate type that was a little cheaper, but I dismissed it because it looked like a Bracket from Home center and bought this one that was on a top ranking.
It can be attached to the Mirror Holder.
The texture is elegant and not bad.
The only drawback is that the angle of the brake lever is not adjustable, so the Master tank may tilt a bit depending on your preference.
And I would have liked to have had Black instead of Plating if possible. View detail

Buy at the same time as Gale MASTER

I bought this at the same time as GALE SPEED's Elabo RateMODEL and Brake master cylinder.
Previously, the top-of-the-line model of the same brand "Elabo Rate. I bought the Clutch of I fell in love with its operability and high functionality and decided to buy it this time. Unfortunately, due to various reasons, I have not been able to replace it yet.
I bought this as a dedicated Tank Bracket. As you can see in the product image, the holder part of MASTER of GALE SPEED is "Master stay mount I thought about using the Universal Bracket, but if there is an Exclusive Bracket, it's better to use it. I haven't actually installed it yet, but I put it together temporarily, and it looks like I can install it without stressing the Tank and Hose. After that, I would like to try to install it without interfering with other parts. View detail

high

I replaced it with Gail's Clutch master, so Quantity:Set to replace it

I'm a little concerned about the dirtiness of the welds for being so expensive!

I wouldn't complain if it was a little cheaper. View detail

Even though it's GALE SPEED?

Used for Master Cylinder of GALE SPEED
I made the tank a GALE SPEED but it doesn't seem to mount horizontally & hellip;
I don't have a problem with it, but maybe it's my methodical nature that bothers me, so I'll bend and adjust it at a later date. View detail

brembo [Color] SmokeTank (S50) Used for installation

Brembo RCS brake master cylinder and smoke tank (S50) I used it to install the
Smoke tank and 8mm high rubber bushings (POSH H-Shaped Rubber PARTS-NO,100202) The combination of the attached M6x20mm bolts and SPL washers does not allow for the use of the nut Do not use an SPL washer and use a normal thin washer because the cling will be reduced I did
After tightening the stay with the mirror, temporarily place the tank and check the level It was slightly tilted, so I corrected it The correction was done by putting the duct tape on the monkey wrench to prevent scratches
We were able to set up the tank well without being distracting in a good way View detail

Suitable right place

TDM900 with YZF-R1's semi-radial master and Ninja H2's I used it when I assembled the Reserver tank

The length and angle are just right, but if you put the Tank on top of the Bracket, it's too high So I decided to fix it on the bottom side as shown in the picture I'm not so good at bending the bracket

This will lower the position of the tank by about 1.5 cm and it looks good

It's twice the price of a DAYTONA bracket, but it fits in just like an OEM Personally, I'm glad I chose this one because it's View detail

That's about it

I have no complaints about the quality The build quality is perfect
I used it to install the Clutch reservoir tank on my GALE SPEED It was a bit too long
View detail

It is as I thought.

I tried installing it and it fell into the state just as I thought. Subtle bend Length If I knew it earlier I could use it elsewhere. Manufacturer is daringly aiming to make it. View detail

The texture is good, but the price is reasonable

I used the same Manufacturer 's GALE SPEED Tank for MT - 09 and GALE SPEED, but I used the same Manufacturer' s GALE SPEED Tank, but the angle was bad and Brake hose bent and broke and could not be used! did. View detail

Ninja H2 OEM reservoir Tank diversion used for Custom

I bought Nisshin's Master cylinder to install the reservoir Tank of Ninja H2.

【What made you decide the purchase?】
I found an article in Nisshin 's Master cylinder that made up Ninja H2' s reservoir tank in a certain blog, so I bought this Bracket according to the information on that blog.

【How was it actually used?】
In Bracket which made plate-like Aluminum standardized in Nisshin's Master cylinder L-shaped, if you slant the Master cylinder, the reservoir Tank will also be inclined together, but if this is a Bracket Bracket itself has a slope on the MASTER side so that even if the master cylinder is tilted it is possible to keep the reservoir Tank level.
Since there is a negative pressure in reservoir tank, even if tank reservoir Tank itself is somewhat inclined, there is no particular harm, but at least if it means to make it look better at least it is not a significant Bracket for Large Is not it?.

【Mounting was difficult?】
Just remove Bolt and Nut and replace it so anyone can easily install it as long as there are tools.

【Please tell me the installation point and hang】
As with me, when you exchange reservoir tank together, I think that once you have decided all the positions and inclination angles and final tighten it will not be a hassle twice.

[Is there anything I was disappointed about?]
nothing special

【Hope for Manufacturer - Please let me know if you have any improvement points]
I think that it will be in an expensive category if it is considered as BracketSingle Body.
If it is a little cheaper it will be easier to buy.

【Have you compared items?】
nothing special

[Others]
Is not it essential to install OEM reservoir tank of Ninja H2 which is recent CustomTrend.
Besides this Bracket
- Posh H Type Rubber 100202
We made it using.
Even if you would like to organize brembo's Tank even for non-Ninja H2, I think that it's also ant to collaborate using this Bracket. View detail

It seemed unlikely Bracket

I used it to divert Kawasaki H2 Reserver tank. This and POSH's H Type Rubber (http : / / www. webike. net / sd / 1257302 / ) Is used.
It is exactly the same as Length, but it is a difficult point that you can not adjust the angle. Pliers were sandwiched between Dustcloths and the angle was adjusted so as not to be scratched. Because it is Aluminum you will hear what you say easily and easily. If it solves it, Bracket that does not claim is felt nice. View detail