There is no correct way to cut.

I bought a second one and tried many different Cutters, but Scissors
I found it to be the best. If you are dexterous, you can use Cutter, Cut
I am clumsy, so I made a protective film for the SeatBack with a commercially available product. It is better to have a paper pattern, though. View detail

It was 3M.

I bought this film to protect the SeatBack of my CBR1000RR-R. Unlike the OEM film, it is easy to cut and good for cowl.
Hard to blend in and become Wrinkle. View detail

Film." Or rather Seal." impression

Since it is labeled "Film," I thought it was supposed to be applied with water, but it is a type that can be cut and applied as is.
Personally, that kind of thing was Image of Seal, not Film.

Because it is not designed to be applied with water, it is difficult for amateurs to apply it to a large area or complicated shape or part without air contamination.
I tried applying the film with water, but it was very difficult to push water out of the film due to the nature of the film, which is not designed to do so (the water stuck in the middle of the film).
Perhaps it is a product that is supposed to be applied to flat surfaces with a pinpoint large size. View detail

Before you damage your new car…

The New Model CROSSCUB110 that I had ordered was finally delivered the other day. I immediately read the various impressions of the senior CUB owners and found that the main pipeCenter cover is easily damaged by foot contact when riding, so I purchased this film to protect my feet while the car is still new. I bought this film to protect my feet while the car was new. Once I removed the main pipeCenter cover, I cut the film to fit the shape, and put it back on the body again. The rest of the cut film was used for the area I wanted to cover on the side of the center cover. View detail

Expectations for effectiveness.

I painted a tank and added a stripe on the cutting sheet to protect the area around the ferrule cap. It is very soft, so it is difficult to apply, but if you apply it with water, you can position it relatively easily.
I checked the adhesive strength with a scrap piece of wood, and it was quite strong and did not leave any marks when peeled off.
You can put it near the Key cylinder. View detail

To prevent scratches

My commuter CUB has a white undercarriage, and before I knew it, it was covered in scratches and dirt from getting in and out of the car (tears).
It's been six months since I started riding, and I'm still looking for items to prevent scratches and stains, and I found this Film.

Quantity:I cut the 1pc. seat into three pieces, one for the main foot, one for the side of the Shift Pedal, and one for the bottom of the keyhole.
It's not impossible to do it by yourself, but it was smoother to do it with two people.
The surface to be applied is slightly curved, so one person should hold the edge of the seat while the other person pulls it to get a good fit.
If you make a mistake, you can reapply. Even if bubbles appear, they will disappear if you press down while stretching the top with a towel.
All in all, I think it's an easy Film to use, even for a beginner or a bit of a klutz!

I've been using it for about a month now, and it hasn't come off or anything.
I'm glad I bought this product because it doesn't make the area where I put it look bad. View detail

Flexible and easy to apply

The rope inevitably comes into contact with the Cowletc. when the Bag is strapped to the Seat when camping touring, and abrasions are attached. Although the contact part with the Cowl was cured with the curing tape every time until now, when the tape was peeled off, even the paint was peeled off together. I thought that this was not good, and this time I cured the Cowl with this product. Because it is a product of the purpose of course, the appearance was also neat, and it was able to achieve the purpose. However, I think that the price can be a little cheaper. I used this product on a previous Motorcycle at Repeat, and even after 10 years, it has not yellowed or hardened, depending on storage conditions. View detail

for peace of mind

I bought this to prevent scratches on the body when loading luggage. I don't want to scratch it unnecessarily, but I also don't want to throw away the feeling that it is used moderately, and honestly, I feel that I could have done without it. View detail

Good product

This is a great product for the protection of the tank and Seat Cowl. It's a thin and soft material and can be attached to a bent area by heating it up. I'm not sure if this is the right product for you. I think it's a good thing that you can cut it into any shape or large size. View detail

Stretchy and easy to apply

Because I put the Side Back on WR250R, I put it on the ZERO-GSide cover
Side cover for construction curing Tape first, and then the pattern production in Magic from that
Cut the curing Tape off well, sticking it to Protection film as it is

Although it is water-based, it stretches very well and can be applied beautifully even on curved surfaces

However, ZERO-G is matte finish, so you can understand that the place where you put it on will be Luster But..
A matted Film would be great too

It is very easy to fit on a curved surface and is recommended to stick it before it gets scratched

We'll see how durable it is, but if it gets damaged, we'll reapply it again View detail