Reviews
If you want to change the look of the Wheel area, this is the way to go.
The appearance around the Wheel and Tire will be Active.
The pasting process is not difficult at all. I have Repeat many times.
When working, don't forget to use a mist of diluted neutral detergent and Squeegee.
For those who want to easily change the look and feel of the product, this is Recommendation.
View detail
I chose it to match the color of the car body.
We decided to put a rim sticker on the Ducati SCRAMBLER to match the color of the car body.
Since MDF had been used for the past three wheels, we chose to purchase MDF this time as well, even though it is a little expensive rim sticker.
I wanted to put up a yellow-colored delicolore, but there was no Variation and only one color, yellow, was available.
There were 18 Rim stickers attached to the two Seats, and at first I could not tell which Size was the front or rear.
The paste was done as described, but it is not perfect.
If you look closely, you can see some distortion, but it does not feel out of place with the Body color, and I hope it stands out anyway to prevent accidents.
View detail
Attached to Ducati SCRAMBLER
I bought this to attach Rim stripe to my newly purchased DucatiSCRAMBLER.
Size is 17&18-inches Color to match the car body color:YellowSingle Body 10mm width was chosen.
I wanted to start pasting immediately, but I don't know which wheel to paste the 18 separate tapes on.
There is no mention of this in the Instruction Manual.
Are the top 8 sheets in the front FOR 18-inches or FOR 17-inches?
Are the two spare sheets the last two on the front or the back?
Are you asking me to paste it in the right way?
As a matter of urgency, I inquired through MDF's Home page.
I have not received a reply yet so I am unable to paste it.
View detail
Name Chain
Since it is a black wheel, it was installed together with Tire's WhiteLetter as one point of reference.
Degrease and apply the paste with soapy water, being careful not to stretch the paste by pulling it.
Maybe it would have been easier with a special tool. I don't know.
Tire is much easier to work with if it is free to turn.
View detail
The important thing is the last Dryer.
I'm getting bored with the pure black Rebel and am slowly adding color.
I was going to use White for the Rim sticker, but I thought it would be better to use the same color as Honda's Emblem, which is a bit raw and silvery, so I chose Light gray, which seems to be the closest color on the Catalogue.
The actual color that I received was a little darker Titanium-like color (but not Gun meta) and I thought it was darker than I expected, but when I put it on, it fit well.
The Rim width of the OEMWheel of REBEL250 is 14mm, so I chose 10mm which seems to be the thickest among the compatible ones.
I wanted to use the special Attachment, but it doesn't support 10mm, so I had to apply it by hand.
With the 10mm Rim sticker, depending on the angle, it looks like the entire Rim is colored, which is cool.
What can I say, the angle is difficult. It's hard to make a circle.
It's a little off, but I'm going to Challenge again when it comes off, so I'm not going to let a little thing get in the way this time.
Degrease it and wet it thoroughly with a thin piece of neutral detergent before applying it.
I match the whole somehow, and when I finish pasting, I adjust it slightly, and finally dry it with Dryer. Or rather, I fix it.
This Dryer was very important.
By applying the Dryer firmly, the Sticker tightens up and absorbs the messy part. I was able to apply the Dryer while tracing it with my finger, and was able to put it on beautifully.
When the Sticker is cooled down, wash it with water to remove the detergent from the Wheel. Now it is completed.
The whole process took about 30-40 minutes.
View detail
Imitation Chain
I'm trying to up-date a 30 year old Motorcycle to 2020s style...
I've heard about NS-1 suspension, but if it's CBX, it must be ComStar.
Spice up your ComStar! That's why I put it up.
Yeah, something about Impact and Parenthesis is good!
View detail
It's a little plain.
It was easy and clean to apply. I don't know how durable it is yet. The color was a little plain. View detail
After applying, apply Dryer.
Attached to Motorcycle for commuting.
Wheel is the part that is badly dirty, so it is better to clean and degrease it thoroughly before applying.
Also, if you apply Dryer after pasting, the sticking will be better.
View detail
Image
When I repainted the wheel in black, I decided to put stripe on it I don't want to have fading and peeling, so I chose this product, and I was worried about using a 6″ wheel, but I decided to use a thicker 10″ wheel The result is just like the Image
For the pasting work, it is not difficult if you follow the Construction Manual I did not Also, I think it's better to cut off the backing and stick it on while peeling off the backing little by little Because I made it thicker, the positioning was easy, so I proceeded to Smooth
View detail
easy to stick to
Adhered to XSR900 with Blue Line 10mm width
It was wide enough to apply it without bending too much
It's a little too obvious, so the 5mm would have been better
View detail
Installed with Gauge (sold separately) The impression of Can Tan, Motorcycle changes gully!
【What made you decide the purchase?】
At first we planned to purchase an infinite Rim sticker, but the price was twice as much as this product, so he was hesitant.
This product is about 3,700 yen for Motorcycle 1 Set for 1 Vehicle, affordable additions, plenty of Review has been posted, easy to grab the image of the product, and commentary animation of the installation method easy to understand on the product page was posted Also decided.
【How was it actually used?】
As shown in the image, the line just entered Rim, it became impressive Sporty at a stroke, it became cool. Large I'm satisfied..
However, although I bought a 10 mm Stripe this time, it was still not full of Rim width, but it was a different point than I imagined if it was far from far away.
【Was it difficult to install? (Hard parts case)】
Because we used Gauge (sold separately), the installation itself was very easy.
(In the case of * 10 mm Rim stripe, processing of Gauge is necessary.
For more info ↓ ↓ ↓ until Impre of Gauge
http : / / imp. webike. net / commu / article / 0282369 / )
The instruction manual was also very polite, so I was able to work with confidence.
Rather cleaning and degreasing of the prepared Rim took much longer.
【Please tell me the point of installation and hang (in the case of Hard parts)】
- For cleaning around the Rim and degreasing, the Instruction Manual "Car wash and degrease" Although it was written, although washing was troublesome, after cleaning carefully with the Car Wash sheet, we cleaned up with paper Dustcloth impregnated with Parts cleaner.
- If you are working outdoors, please be careful that Small stones and Small Nagomi will not stick to the sticker surface.
If you paste it as it is, it will float up from the bottom of the Sticker.
[Is there anything I was disappointed about?]
This is not Sticker but Gauge's fault, but I wanted to put the Sticker on the outside rather than inside the Rim.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Is it even possible to have a thick Size?
【Have you compared items?】
Infinite Rim sticker
[Others] nothing special.
View detail
Street Image
It is a little Large change to paste. It will take time to paste tightly. Well, it's just bad.
With Maintenace Stand, I think that you do not have to stop Motorcycle by pushing and stopping.
Although it is periodically done like WheelCleaning after pasting, it is pretty crisp but it does not appear to peel off. I think that durability is good. There are also various colors, so you can customize for yourself.
View detail
You can easily Wheel's Dress-up!
This time it is the third one to paste MDF's Rim stripe.
Simply remove the Rim with Parts cleaner and paste it.
There are things like dedicated rulers when sticking Rim stripe
As it is, it is always adhered to the center of Rim and it is quite beautiful if it is fitted only with the joint of Stripe neatly
It will be a circle.
I can make it in 30 minutes in the whole process and overall image will be better
I purchase it every time I change Motorcycle.
View detail
The red rim was attached to ZRX400 of red. 10 mm, it is quite thick, and attaches, or becomes and is conspicuous. although it only merely stuck since the appearance near Tire changed a lot -- custom-made one -- in the bottom, atmosphere com
The red rim was attached to ZRX400 of red.
10 mm, it is quite thick, and attaches, or becomes and is conspicuous.
although it only merely stuck since the appearance near
Tire changed a lot -- custom-made one -- in the bottom,
atmosphere comes out enough.
Above all, since it has already curved, it is quite easy to stick.
If a little
neutral detergent is attached, adjustment of some resticking will hear.
Since vehicles must be restlessly moved if it has neither vehicles without the
Center stand, nor a Racing stands, only a few is troublesome.
View detail
10-mm Red wearing was carried out at the black Wheel of ZX-14R. Although it wavered at 6 mm or 10 mm, 10 mm was used and he was Satoru Taisho. Before. The Impact was more missing although a 6-mm Blue was stuck on the silver Wheel of ZZR1400. 10 m
10-mm Red wearing was carried out at the black Wheel of ZX-14R.
Although it wavered at 6 mm or 10 mm, 10 mm was used and he was Satoru Taisho.
Before.
The Impact was more missing although a 6-mm Blue was stuck on the silver Wheel of ZZR1400.
10 mm was an Exactly at these vehicles.
Since the optional exclusive Gauge did not correspond to 10 mm, it was anxious before work, but since one duties were three division, it was able to construct easily.
A Recommendation can be carried out to any vehicles.
View detail
It stretched to the XR250MOTARD. It will be OK if this much conspicuous at this price. I think that anyone can do it if attachment carries out cleaning etc. and they are stuck carefully. An awkward one was also able to do it. Although wh
It stretched to the XR250MOTARD.
It will be OK if this much conspicuous at this price.
I think that anyone can do it if
attachment carries out cleaning etc. and they are stuck carefully.
An awkward one was also able to do it.
Although what was purchased before
will leave for three years, it has stuck perfectly.
View detail