I'm satisfied.

I was able to install it. How does it feel on a rainy day?
Also, to be honest, I didn't want to drill the holes with Drill, so I stuck it on at first with the adhesive tape that came with it, but still. Do you like the design or something? View detail

Extended OEM Front Fender length

Water and mud splashes are reduced and feet are less likely to get wet.
After driving on a forest road, mud was accumulating and hardening near the cooling fan. After installation, the mud splashing was reduced and the mud no longer splashed onto the cooling fan.
Double-sided Tape and Clip for mounting in quantity:It comes as a set. I drilled a hole in the Fender and installed the Clip only, without double-sided tape for easy removal. View detail

Note the placement of the double-sided tape.

Dirt comes up to the Radiator and Stem, so it is installed.
It is more troublesome than expected because it is necessary to remove the Wheel to remove the Fender.

It fits perfectly without Tape, so if Tape is applied to the sides, it will not go all the way in due to the thickness and adhesiveness of the Tape.
So, I only put it on the front part, but it can be fixed quite firmly.
However, since the motorcycle runs 300km, the included Rivet must be used and a 4mm hole must be drilled just in case.

The black color on the green-light Fender is almost conspicuous, but since it is located in the back of the house, it is hardly noticeable.
I have used it on other cars and the spray stops around the bottom of the Radiator, which makes washing the car easier. View detail

Mudguard on bmw r1200r

Installation is a simple process of attaching with the included double-sided tape.
Effectiveness.
Small stones and mud rolled up by Front are reduced.
If only it were a little longer? 5. View detail

FenderExtender on the grom

I purchased these to reduce mud splatter on my Horizontal TypeEngine when I bought my Grom new. I used 3M double-sided tape instead of the supplied double-sided tape for installation. It has been 7 years and 56,000km since I bought it and it has reduced the mud splatter without any deterioration. I thought that the cost performance might not be so good, but I have not had any problems for more than 50,000 km, so I felt again that it is a good product. View detail

Satisfied with the sense of togetherness

I installed it on my 2021MODEL. It is cheaply made, but I feel no problem to integrate it with Fender.
We have not used it in the rain yet, but we expect it to reduce mud splashing. View detail

Extender Fender

[How is it used? Extension for short FFender.

Was the one you received as per Image? usually

How was your experience with it? usually

[Points to note] The Pin of the resin is poor.

How did it compare to other products? None

Other items that would be helpful
Point and hang of installation/Items to be purchased together/Opinions and requests to Manufacturer None View detail

practicality

I'm sure it will look bad, but it is practical. I don't have a photo of it as I don't have a vehicle at hand, but it has reduced the amount of mud splashing from stepping stones. I asked a motorcycle shop to fix the Rivet so I didn't have to worry about it falling off. If you are looking for something practical, this is the Recommendation. View detail

Peitzmeier Company Extender Fender

There was a lot of bouncing off the front wheels when it was raining or there was water on the road, but after installing the Extender Fender I was pleased with the effect. It is best to remove the OEM Fender when installing it. View detail

impossible to install

The shape did not fit and could not be processed, so it was Garbage. View detail

Effective in preventing mud splashes

I installed this on my NC750X 2021.
I installed it because the Fender is too short for OEM and it makes the car body dirty.
It is recommended to fix it with Double-sided Tape and Pin, but since the quality of the Double-sided Tape that was included seemed to be good, I installed it only with Double-sided Tape.

I've driven about 500km and there's no sign of it coming off. View detail

Front mudguard extension

My car is made by Honda, the model is NC750X, and the year is October 2020. I bought P&A’s front fender on webike. Its material is plastic; I don’t know why the original car’s front fender is so short? When installing this extension plate, the front fender of the original car must be removed and fixed with 3M glue. It is best to use 3 or 4 rivets to fix it. It is still not possible to ride too fast, otherwise the radiator plate of the water tank will still be thrown. . ---------------------------------------------- My car is Honda brand, model is NC750X, the year is October 2020. I buy on webike the front fender of goods P & A, and its material is plastic; do not know why the original car's front fender so short? When installing the front fender panels should extend the original car demolished, fixed with 3M adhesive, preferably with three or four rivets fixed, or can not ride too fast, otherwise it will still dump tank cooling plate. Powered by Google Translator View detail

Extender Fender Installation on 2020 Grom

I installed it on the Grom.
The Size of the extension is also just about right, which is nice.
The reason I wanted to install this is that the NORMAL Fender is short
Even the top side of the cylinder head has mud splatter and is very dirty and difficult to clean!
For installation, remove the Fender and fix with Double-sided Tape and PlasticHook.
You will have to drill the Hook holes yourself.
After installation, there is mud splash on the bottom of cylinder but not on the top of head.
It's gone. View detail

Clearly effective, 120 points of satisfaction

The design and quality of this product is perfect. The front fender is too short to begin with. View detail

I want to start with a new car.

Front fenders tend to be shorter these days, and although parenthesis is good, there are more water splashes and small stone ricochets, and more scratches and dirt on the engine, exhaust pipe, and radiator. This is especially recommended to those who are worried about such things. I started using it on my last car and it was very effective and I put it on the car I replaced right away. I do not want to go touring without it. Installation is a bit of a hassle but I would recommend removing the Fender as it is easy to position and prep. I installed it without removing it. I installed it with just the double-sided tape that came with it and checked it when I washed the car. The quality of the texture is good, but the surface is still plastic, so you may want to blow it clear or something else if you like. The shape of this product is for car models only.
It came on nicely, Cost performance was subtle before I used it, but now I think it's very high.








View detail

2

I cut it about 15mm because it makes contact with the Tire
Still, Clearance is no more than 5 millimeters
I think it's a Universal Product, not 900RSpec
View detail

Surprisingly Exactly

Installed in VFR800F

Fitting is surprisingly good (to the point where you might think it's a specialized product)

Bottom line is, the bounce is down 40%. I'd say that's about it

However, the installation was very Large strange to remove and install the Fender
View detail

I'm happy with the functionality

The Extender for the YamahaBOLT Shoulder Bag is just as you rated it For the price, the molding is not as good as it should be
That's all I can say

It's a reasonable price, and I'd like to see you manage the product well
At any rate, the mud splash from the BOLT Shoulder Bag's Front Fender is awesome
I can't change my back when I think about the cleaning process
Before you put it on, you can use Quantity:Pair (for Left and Right) It's not symmetrical, and it's not symmetrical at all
Once you put it on, it's not very noticeable
But the function, no complaints The mud splash is now about 1/3 of what it was before I put it on

I glued it on with the included Double-sided Tape
But I was worried about the strength of the gun, so I used my secret weapon, the heat gun
GunGun seared it and kept it close

I've been touring for 450km after installing it, and I've been vanned out on highways and mountain passes
There is no indication that it is likely to be taken View detail

To prevent mud, stones, etc. from sticking to the Engine

I chose this product because I can't find any other dedicated Mud Guard products to run various places
Installation is easy
The included Double-sided Tape is strong and includes an extra pin for reinforcement but
I didn't want to make a hole in it by reinforcement, so I used Double-sided Tape and I played SiliconCoking
The accuracy of the Gold model is good and Exactly, and I like the functionality without any discomfort after wearing it
Honestly, how is 5,000 yen for this small plastic part? I thought for a bit
View detail

After the rain..

A bit of a problem for GromUser.. "Dirt around the engine head after running in the rain and after rain This symptom is a stipulation of the Horizontal TypeEngine The product that solves such problems is the one I bought this time "Peitzmeier Company:Extender Fender Fender It is



Let's start with the Impression of the product content!

Products include the Handling and Installation Instruction Manual, Extender Fender Fender, and Screw to prevent falling out, AlcoholWipe (degreaser), Double-sided The contents of the tape The unreliable attached Double-sided Tape which was in Impression until now is It has been changed to the strong Double-sided Tape that has been versioned up Probably, when the Extender Fender attachment fails and it peels off.... I'm sure you'll let them, so be careful where you stick them! It is If you fail to do so, I recommend that you warm it up with Dryeretc. and peel it off In that case, do it at your own risk!



Next is an Impression of the Extender Fender installation

I am a "Anti-shell screw In order to use Extender Pre-install the Fender After temporary installation, please add the Quantity:Pair (for Left and Right) In order to decide the position of the screw installation for preventing the screw from falling out of the screw, decide the reference point to OEMFender To install the screw to prevent the screw from falling out, please check the diameter of the head part and make sure that the hole is 4mm We make sure of the positioning If the positioning is done well, it will look like the OEM finish On the other hand, if you fail, the result will be unnatural, so be careful! That's it If you can make it to that point, you need to drill the screw mounting hole for prevention of falling out It is the basis of Drill, but it is not to drill a large hole at once, but to drill a large hole gradually It's all about opening it up! I process the drill with the degree of caution to the extent that I beat a stone bridge and cross it (laughs) After the processing is successfully completed, the OEM Fender and the Extender Fender can be used with the attached degreaser Use to degrease After degreasing, attach the included up-dated double-sided tape to your spec After applying Double-sided Tape, the OEMFender is carefully attached Install the Extender Fender securely (If the position is misaligned, the Double-sided Tape Firmly works I think you will damage the Extender Fender, so if you do so, use Dryeretc I suggest you heat it up and peel it off with a When the Extender Fender is securely attached to the mounting position, you can use the Install the Screw and let it rest for 12 hours I used a Clamp to fix it in place and left it resting!



Now it's time to install Impression on the vehicle

The Extender Fender is also included with the double-sided tape to prevent it from falling off By using Screw, I was able to install it in the OEM Fender after attaching the sided tape, I fixed it with clamps for more than 12 hours and left it to rest I was able to Firmly install it on the OEM Fender Now it's time to install it in the vehicle and it's easy to do with the 10″ tool and the Hexagonal Wrench The OEMFender can be returned After the installation, there is no interference in the Tire of OEM Fender, and there is no interference in other parts I think it is the proof that the shape and details are well made



This is the overall Impression of Extender Fender The making of "OEM? I think that this is the place that makes me think that it is a good product However, if you use only the attached double-sided tape, you will need some additional processing But if you use the screw for prevention of falling off, you need to do some positioning and drilling etc I think it will be a burden for those who are not used to processing The durability and the role of Extender Fender will be felt by using it in the future I think that's part of it, so we'll have to wait and see how you rate this one! Let's just say How is the Cost performance worth the $5400 selling price? If you're saying, "I don't know what to do," then... I'm sure people have different opinions, but if you're saying, "I don't know what to do," then you're wrong Then I think it's a reasonable Gold amount for me View detail