- Beranda
- Motor
- HONDA 126 - 250cc
- NSR250R
- Perkakas
- Peralatan Khusus Motor
- Peralatan Khusus Motor Lainnya
- DMR-JAPAN
- DMR-JAPAN: Sproket belakang: FlangePuller
Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat SemuaRincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
Isi Produk: Sproket belakangFlangePuller Jumlah: 1 Set
Product Description: Rear Sprocket Flange Puller 1set
[Deskripsi]
Ini adalah suku cadang asli DMR-JAPAN.
Ini adalah alat khusus untuk melepas flensa yang menahan Sproket Belakang MC28 di tempatnya!
Hal ini dimungkinkan untuk menghapus SprocketFlange yang sulit untuk dihilangkan karena kesalahan tekan-pas pada produk atau kepatuhan penuh oleh Rust atau Maggots ..
Karena SprocketFlange terbuat dari Aluminium, terdapat risiko kerusakan atau perubahan bentuk saat mengeluarkan Sprocket dengan sendirinya ..
SprocketFlange dirancang dengan total 12 titik untuk mencegah gaya berlebihan yang diterapkan ke SprocketFlange ..
Bagian tengah Penarik Roda Terbang telah diproses dan dipasang, sehingga Anda dapat menggunakan kunci pas!
Jika sekrup di tengah rusak, dibuat agar bagian-bagiannya bisa diganti .. DMR-JAPAN original parts
This is a special tool for removing the flange that fixes the rear sprocket of the MC28!
It is possible to remove the sprocket flange which is difficult to remove due to the press fit by the product error or the complete adherence by rust or galling.
Since the sprocket flange is made of aluminum, there was a risk of damage or deformation if it was pulled out only at the sprocket mounting.
Therefore, the sprocket mounting part and the flange itself were gripped, and the layout was made so that excessive force would not be applied to the sprocket flange with a total of 12 points.
The center of the flywheel puller has been processed and installed so you can use an impact wrench!
In case of damage to the central screw, it is made so that parts can be replaced.
Ini adalah alat khusus untuk melepas flensa yang menahan Sproket Belakang MC28 di tempatnya!
Hal ini dimungkinkan untuk menghapus SprocketFlange yang sulit untuk dihilangkan karena kesalahan tekan-pas pada produk atau kepatuhan penuh oleh Rust atau Maggots ..
Karena SprocketFlange terbuat dari Aluminium, terdapat risiko kerusakan atau perubahan bentuk saat mengeluarkan Sprocket dengan sendirinya ..
SprocketFlange dirancang dengan total 12 titik untuk mencegah gaya berlebihan yang diterapkan ke SprocketFlange ..
Bagian tengah Penarik Roda Terbang telah diproses dan dipasang, sehingga Anda dapat menggunakan kunci pas!
Jika sekrup di tengah rusak, dibuat agar bagian-bagiannya bisa diganti .. DMR-JAPAN original parts
This is a special tool for removing the flange that fixes the rear sprocket of the MC28!
It is possible to remove the sprocket flange which is difficult to remove due to the press fit by the product error or the complete adherence by rust or galling.
Since the sprocket flange is made of aluminum, there was a risk of damage or deformation if it was pulled out only at the sprocket mounting.
Therefore, the sprocket mounting part and the flange itself were gripped, and the layout was made so that excessive force would not be applied to the sprocket flange with a total of 12 points.
The center of the flywheel puller has been processed and installed so you can use an impact wrench!
In case of damage to the central screw, it is made so that parts can be replaced.
Peringatan
* Harap diperhatikan bahwa spesifikasi produk dapat berubah karena alasan pabrikan.
*There may be changes in product specifications due to the manufacturer's reasons.
*There may be changes in product specifications due to the manufacturer's reasons.
Model yang Sesuai
PRODUK YANG JUGA DILIHAT
Produk Siap Dikirim dari Gudang Jepang
Rekomendasi buat Kamu
Best Seller
New Custom Article
Gunakan kupon
Review Gambar
Review detail
/