Monkey125 18-23 Compatible with normal up-type muffler
Rincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
Ukuran: Panjang keseluruhan L335mm ±5mm Warna per: Diamond Black Piston rod: Chrome plated Sesuai dengan knalpot standar tipe up Size: Overall length L335mm ±5mm Spring Collar: Diamond Black Piston rod: Chrome plated Compatible with normal up-type muffler
[Deskripsi]
Untuk pengaturan dasar (pada saat pengiriman) , ini adalah klik ke-14 dari 30 KETEGANGAN (Sisi ekstensi) Langkah. (Cara standar untuk mendapatkan nilai standar ada di sisi MAX, dari posisi dikencangkan penuh ke kanan, kembali ke kiri.) COMP (Sisi Tekanan) Klik ke-11 dari 20 langkah Penyetel awal antara 0-10mm. Nilai default diatur pada 4 mm. (MIN + klik ke-9)
For the basic setting (at the time of delivery), it is the 14th click out of 30 TENSION (extension side) steps.(The standard way to get the standard value is on the MAX side, from the position where it is fully tightened to the right, back to the left.) Compression (pressure side) 11th click out of 20 steps Initial adjuster is between 0-10mm. The default value is set at 4mm.(MIN + 9th click)
Catatan
* Gambar hanya untuk referensi. Gambar yang ditampilkan mungkin berbeda dari produk yang sebenarnya.
Peringatan
*Harap jangan kencangkan secara paksa setelan dasarnya. Setelah memasang produknya, harap kencangkan mur end eye di sisi di mana preload adjuster per dikencangkan di seri RS dan cek kembali. Untuk mengatur end eye dan kecangkan mur penguncinya, lepas shock dan kencangkan shock menggunakan alat dengan tang dan sejenisnya lalu kencangkan mur pengunci pada 40 N/mm + aplikasikan kunci torsi. Jangan lakukan ini saat produknya masih terpasang di motor. *Produk ini bukanlah produk yang dapat dibongkar. Karena ada gas nitrogen tekanan tinggi, jangan terkena kontak dengan api saat membuangnya atau dapat menyebabkan ledakan atau kebocoran oli. *Harap diperhatikan bahwa spesifikasi produk dapat berubah karena alasan produsen.
*Please be sure to observe the following items when installing the product.Since they are the most important safety parts, failure to do so may cause a serious accident. *Installation is not allowed at any factory other than a certified factory, as they are the most important safety parts.This is not a claimable item. *Some models may require modification to the side cover if the suspension sub-tank is installed in the opposite direction (with the sub-tank facing the direction of travel). *When installing this kit on some models, please make sure that left and right hand exhausts, other brands of exhausts, and rear caliper mounting bolts do not interfere with the kit.If there is interference, it cannot be used.Advantage has also checked stock exhausts and exhausts produced by other companies, but not all of them.Adjustment is also required for interference with torque rods and drive chains. *These products have passed all strength tests.There is no deformation of the shock unit or oil leakage except for the mistake.Please handle with the utmost care.Be sure to perform surface preparation (greasing) on peripheral work prior to installation. *This kit is sold as Japanese specifications for Japanese use only and does not support conditions of use outside Japan. *For inspection of each part, please inspect before every start (daily inspection), every 3 months, and every 1, 000 km, although it depends on the category.For track use, it is an inspection every time.Please contact Advantage for inspection of any defective products. Please send all items to Advantage. *Please do not forcefully tighten the basic setting. *After assembling the product, please tighten the end eye nut on the side where the spring initial adjuster was tightened in the case of the RS series, and recheck it. *To adjust the end eye and tighten the lock nut, remove the shock and secure the suspension itself using a jig with bipliers, etc., then tighten the lock nut at 40 N/mm + apply a loosening torque wrench to secure it.Never do this while the unit is still attached to the bike. *Products are non-disassembled products.Since high-pressure nitrogen gas is contained, do not allow it to come into contact with fire when disposing of it, or it may explode or oil may spurt out. *There may be changes in product specifications due to the manufacturer's reasons.
Model yang Sesuai
Monkey125 18-23 Compatible with normal up-type muffler
