Cek kupon saya
Jumlah
100% Ori
Garansi 7 hr
Gratis Cashback
Nett Tanpa Biaya Tambahan
Model yang Sesuai
Lihat Semua
Rincian Produk
Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik
Lihat versi asli
Spesifikasi:
Satu set plat kopling groove cut, chamfered (4 pcs)
[Deskripsi]
Plate is the same as for SEROW225 (5 plates).
The only difference is the number of sheets.. I'm also putting it in SEROW225 WE in Kitamura, Kobo..
We have been looking for a reliable material to replace our expensive OEM Clutch Plates.. Found..
I repeated the test in my vehicle.. It is a perfect circle Type and the performance is perfect..
The material plate itself is less expensive than OEM, and although it takes more time to groove and plane the surface (than OEM processing), we were able to lower the selling price compared to conventional products..
0In the case of this car model
Control of semi-cra is difficult..
The change of Touch by the riding time and situation is Large.. (Heat Dare)
Clutch will burn if you struggle in the mountains or in difficult places..
Clutch is not cutting it..
I can't make a quick connection..
Hard to get into Neutral.
Shift is hard even if the clutch lever is fully grasped..
...stalls immediately..
It is effective in improving such things as.
SEROW,TWetc. The clutch of the "L" is located in the upper part of the crankcase, above the oil level..
Oil relies on supply from central Clutch.
This is due in part to the fact that the priority was placed on cutting the car as a production car for general public roads..
If you have replaced the clutch plate on this engine, you may have noticed that there is really only a little oil left in the disc..
Very easy to burn..
The groove-cut beveling plate is more precise and flatter, so there is less distortion (rattling, sagging) of the oil buildup, but the groove holds the oil in place (half cut) so that it is always stable, "no matter how it is used".. It is one of those funky ideas for you!
We did not just want to retain the oil, but we wanted a touch that is easy to handle, from gentle riding to full throttle driving..
I tried Dot, drilling, etc., but this process was the best in many situations..
So, to put it another way, it is always wet, so there is a slight drag, but the temperature change is small and it is difficult for the Friction Disc to reach a high temperature that would cause carbonization..
If you are concerned about the drag, please use a clutch spring retainer..
Retainer reduces abnormal vibration of the clutch and improves the clutch's sharpness..
YZetc. In the grooving and chamfering of Racer and TRIAL for vehicles, the clutch is below the oil level, so the oil is cut all the way through (end to end) to facilitate lubrication..
Processing to cool down by discharging more and more.
Half-slice" and "full-slice" serve completely different purposes..
When I tested a full cut like YZ on SEROW, it got burnt immediately!.
[Image description]
Image 1. New Model(Round Type)Quantity:1 Set of 4pcs. Quantity:Set. I think this shape and processing gave us just the right balance..
Image 2. Immediately after a hard test on SEROW225. Holding Oil. Discolored, but good with little distortion and wear.. In this state, Friction Disc can be used continuously.. (Plate is OEM Variant Type)
Image 3. Grooving and chamfering was one of the elements of "ClutchTuning" to machine ClutchBody.. The effect of processing Plate is also Large and so it is one of the Items.. The clutch spring retainer is different from the clutch spring retainer in that it works differently.. (Image:RTL-F)
Image 4. As written on the packing bag, when assembling, please assemble the one with the rounded left corner on the Engine side..
This processed product does not depend on the friction force and connection by the surface roughness of the clutch plates when they are new (early GSX400EGSX400E)..
The surface roughness and contact area are increased by chamfering, and the surface pressure is increased by groove cutting, etc.. The frictional force is obtained by.
This type holds oil in the groove and reduces heat generation.. It is one of those funky ideas for you!
It is flat and smooth because it is beveled.. Since there is little change in the reduction, the change in Touch will be less in the short and long term..
Normally, Friction Disc and Clutch Plates must be replaced at the same time, or they will start slipping quickly..
Plate" is the name of the process, but it is also used to flatten the distortion of a new piece by beating or bending it, groove cutting, and final BALI removal.. is correct..
Processed by hand in our workshop.
The only difference is the number of sheets.. I'm also putting it in SEROW225 WE in Kitamura, Kobo..
We have been looking for a reliable material to replace our expensive OEM Clutch Plates.. Found..
I repeated the test in my vehicle.. It is a perfect circle Type and the performance is perfect..
The material plate itself is less expensive than OEM, and although it takes more time to groove and plane the surface (than OEM processing), we were able to lower the selling price compared to conventional products..
0In the case of this car model
Control of semi-cra is difficult..
The change of Touch by the riding time and situation is Large.. (Heat Dare)
Clutch will burn if you struggle in the mountains or in difficult places..
Clutch is not cutting it..
I can't make a quick connection..
Hard to get into Neutral.
Shift is hard even if the clutch lever is fully grasped..
...stalls immediately..
It is effective in improving such things as.
SEROW,TWetc. The clutch of the "L" is located in the upper part of the crankcase, above the oil level..
Oil relies on supply from central Clutch.
This is due in part to the fact that the priority was placed on cutting the car as a production car for general public roads..
If you have replaced the clutch plate on this engine, you may have noticed that there is really only a little oil left in the disc..
Very easy to burn..
The groove-cut beveling plate is more precise and flatter, so there is less distortion (rattling, sagging) of the oil buildup, but the groove holds the oil in place (half cut) so that it is always stable, "no matter how it is used".. It is one of those funky ideas for you!
We did not just want to retain the oil, but we wanted a touch that is easy to handle, from gentle riding to full throttle driving..
I tried Dot, drilling, etc., but this process was the best in many situations..
So, to put it another way, it is always wet, so there is a slight drag, but the temperature change is small and it is difficult for the Friction Disc to reach a high temperature that would cause carbonization..
If you are concerned about the drag, please use a clutch spring retainer..
Retainer reduces abnormal vibration of the clutch and improves the clutch's sharpness..
YZetc. In the grooving and chamfering of Racer and TRIAL for vehicles, the clutch is below the oil level, so the oil is cut all the way through (end to end) to facilitate lubrication..
Processing to cool down by discharging more and more.
Half-slice" and "full-slice" serve completely different purposes..
When I tested a full cut like YZ on SEROW, it got burnt immediately!.
[Image description]
Image 1. New Model(Round Type)Quantity:1 Set of 4pcs. Quantity:Set. I think this shape and processing gave us just the right balance..
Image 2. Immediately after a hard test on SEROW225. Holding Oil. Discolored, but good with little distortion and wear.. In this state, Friction Disc can be used continuously.. (Plate is OEM Variant Type)
Image 3. Grooving and chamfering was one of the elements of "ClutchTuning" to machine ClutchBody.. The effect of processing Plate is also Large and so it is one of the Items.. The clutch spring retainer is different from the clutch spring retainer in that it works differently.. (Image:RTL-F)
Image 4. As written on the packing bag, when assembling, please assemble the one with the rounded left corner on the Engine side..
This processed product does not depend on the friction force and connection by the surface roughness of the clutch plates when they are new (early GSX400EGSX400E)..
The surface roughness and contact area are increased by chamfering, and the surface pressure is increased by groove cutting, etc.. The frictional force is obtained by.
This type holds oil in the groove and reduces heat generation.. It is one of those funky ideas for you!
It is flat and smooth because it is beveled.. Since there is little change in the reduction, the change in Touch will be less in the short and long term..
Normally, Friction Disc and Clutch Plates must be replaced at the same time, or they will start slipping quickly..
Plate" is the name of the process, but it is also used to flatten the distortion of a new piece by beating or bending it, groove cutting, and final BALI removal.. is correct..
Processed by hand in our workshop.
Peringatan
*Even if the "thickness of the friction disc" is within the manual's specified value when replacing the plate, if the cork grains are so black and carbonized that they cannot be distinguished, it is the "end of life". When you put your fingernail on it, you will feel a crunching sound, and it is not cork (friction material) but charcoal with little friction force.
*The image may contain other products.
*Please note that the product specification may change due to manufacturer reasons.
*The image may contain other products.
*Please note that the product specification may change due to manufacturer reasons.
