Kembali ke atas

【ZETA】Handguard Armor (Model Tekuk)

Harga: Rp1,671,000

*Termasuk PPN 10%

Nikmati cicilan 0% mulai dari Rp139,250/bulan

Webike Points: 16,710 pts

Shipping point: 13.3 pts ( 13.3 pts x 1qty)
Ubah
DKI Jakarta, Jakarta Selatan, Cilandak
Biaya pengiriman
Rp18,000

Mohon pilih varian produk terlebih dahulu.


Rincian Produk

Konten ini diterjemahkan oleh Google, jika Anda ingin melihat aslinya, silakan klik Lihat versi asli

[Spesifikasi]

[Isi Produk (untuk Kiri dan Kanan)]
Badan Pelindung Tangan Pro Armor
Adaptor Ujung Batang untuk Pelindung Tangan Armor Pro
Bumper Pelindung

[Catatan]

* Gambar hanya untuk referensi. Gambar yang ditampilkan mungkin berbeda dari produk yang sebenarnya.

[Peringatan]

* Kit pemasangan tidak termasuk dalam produk ini. Silakan beli kit pemasangan secara terpisah.

[Deskripsi]

Ini adalah model evolusi pelindung tangan lapis baja yang ditingkatkan berdasarkan permintaan pengendara profesional.
Ini melindungi bodi pelindung tangan paduan aluminium berkekuatan tinggi, dan dilengkapi dengan bumper plastik tahan lama sebagai standar.
Itu membuat pelindung kokoh dengan mendesain adaptor ujung batang yang panjang.
Selain itu, ini mencegah masalah seperti pelindung bergoyang dan bergeser saat menerima guncangan dengan memasang sambungan bodi pelindung dan adaptor ujung palang.
Anda dapat memasang pelindung tangan yang dijual terpisah.
Ini sesuai dengan diameter dalam stang 13,5-14,5mm.
  • 4.2

    16 Ulasan

  • 5

    Memuaskan

    3

    4

    Bagus

    13

    3

    Lumayan

    0

    2

    Kurang

    0

    1

    Mengecewakan

    0
  • Tulis Ulasan

    Because my favorite OklahomaHand guard was broken, I tried to purchase the best but also finished selling.

    Because it was 15 years or so I guess it can not be helped ? ?

    There was also a similar cheap commodity so I got lost but it seems to be sturdy so purchase.

    There is weight feeling besides getting products.

    If you have experienced hand guard Instruction Manual I think Large is durable without looking.

    Find and locate positions that do not interfere with Harness, Wire, Hose and others around Handlebar.

    The top bridge side is not settled straightforward, and it is the position where it is most impossible to temporarily tighten
    Final tightening.

    Titanium color was astringent and correct.

    CRF250L (2014) Attached to.
    It was a suspicion that I could successfully install it with only the attached Bracket of Hand guard, but since it seems that OptionBracket is not used especially at every imprint, it is judged that Large will be durable and purchase.

    Results were attached firmly with attached kit only.
    However, since the Handlebar of CRF is two-tiered, in order to tighten Screw of HandlebarBracket, the head of Screw is set on the ground side (Lower) If you do not do it, Screw can not be tightened, so be careful. In fact, it is preferable that the Screw head is facing upward rather than entering the Screw hole without water droplets or dust, but it is inevitable because Screw can not be tightened.

    Processing of Handlebar Grip is necessary. Especially the Throttle side Grip hole was blocked with resin, so it was necessary to drill holes in this. Rubber cut with Cutter and resin part drilled with Reamer.

    Clutch SideFlip hole is Opening so RubberCut is OK only.

    Handlebar fixed BracketScrew uses the attached Large Size.

    Finally I could fix it as Firmly if I screw up the Screw of each part in the order as ordered.


    Necessary to run off-road but essential in town! Although there was an accident in the past, Door of a traffic jam suddenly opens Door Edge holds Handlebar running on my hand Fighting bones I have broken. There are lots of obstacles such as rocks and branches if you are running through forest roads, so you can drive safely from the accident experience.

    I used the Guard of PlasticType so far, but when I hit the tree I pinched my fingers and hurt my fingers as if I thought they broke, so I bought a reliable standard jitter.
    Handlebar got a little heavy, but it was broken, etc.. I think that it is better than to hurt. (It is still unknown about the effect because there are no scenes that demonstrate the effect)

    It would be nice if the Clamp part on the Handlebar was made a bit shorter,
    WR250 (OEMHandlebar) It is about 5 mm long and it does not work well unless you attach the end part of the Handlebar in a distorted form. Is it such a thing if it is not exclusively for the model?
    It may not be possible to recommend it for people who become small postcards.
    The product is not bad, but if this workmanship it would be fine to lower the price.

    It would be nice if the Clamp part on the Handlebar was made a bit shorter,
    WR250 (OEMHandlebar) It is about 5 mm long and it does not work well unless you attach the end part of the Handlebar in a distorted form. Is it such a thing if it is not exclusively for the model?
    It may not be possible to recommend it for people who become small postcards.
    The product is not bad, but if this workmanship it would be fine to lower the price.

16 Ulasan Lihat semua