- Beranda
- Ulasan Produk
- Sparepart Motor
- Sparepart Mesin
- Sparepart Pengapian
- Speed Limiter Cut
- Itu melekat pada 08 MODEL CB1300SB. Tujuan pengg... (POSH: RED REV Super Limiter Cut)
【POSH】RED REV Super Limiter Cut Review
Sesuai: HONDA CB1300 SUPER BOL D'OR, HONDA CB1300SUPERTouring
It attached to 08 MODEL CB1300SB. The purpose of use is cutting the Speed limiter at the time of a Circuit run. Since this product cuts only a Speed limiter and a Rev limiter is effective firmly, there are no worries about an Overrev. therefore, h
It attached to 08 MODEL CB1300SB.
The purpose of use is cutting the Speed limiter at the time of a Circuit run.
Since this product cuts only a Speed limiter and a Rev limiter is effective firmly, there are no worries about an Overrev.
therefore, he is kind to an Engine -- it was the touch ?.
230 km/h was [ CB1300 of the FOR JAPAN MODEL ] actually a limit in the Circuit.
It is not extended any more.
Although it is
attachment, it is not necessary to do large-scale work specially.
Only with an attached description, it is attached enough.
The black Cover of the Meter left is removed first.
Since wiring is contained in the receptacle of a form like [ inside ] a bag, it is taken out in it and it is made to sink below a Coupler in it.
Then, work is termination only by raising a Tank (the way is written on the instruction manual of a Motorcycle), making wiring of the left Side cover interrupt, and finally connecting long pink wiring to a Coupler along with a Main harness under a Tank at through and the last.
Since pink wiring was fairly last-minute die length, it is necessary to make it the position in which it does not interfere when a wheel is turned.
If it is a direction whose soldering will be possible since it does not become a problem if it excels 5 more cm, it can wire for a long time easily.
Anyhow, attachment was easy and the end of work in about 30 minutes.
Although that is right, when [ which may be upgraded depending on a vehicle type ] it is CB1300SB, it has not said so and only a Speed limiter is cut purely.
Itu melekat pada 08 MODEL CB1300SB. Tujuan penggunaan adalah memotong Pembatas Kecepatan pada saat Sirkuit berjalan. Karena produk ini hanya memotong Speed limiter dan Rev limiter sangat efektif, tidak ada kekhawatiran tentang Overrev. oleh karena itu
Itu melekat pada 08 MODEL CB1300SB. Tujuan penggunaan adalah memotong Pembatas kecepatan pada saat Sirkuit berjalan.
Karena produk ini hanya memotong Speed limiter dan Rev limiter sangat efektif, tidak ada kekhawatiran tentang Overrev. oleh karena itu, dia baik pada Mesin -- itu adalah sentuhannya?.
230 km/jam [ CB1300 dari FOR JAPAN MODEL ] sebenarnya merupakan batas di Sirkuit. Tidak diperpanjang lagi. Meskipun itu
lampiran, tidak perlu melakukan pekerjaan skala besar secara khusus. Hanya dengan deskripsi terlampir, cukup dilampirkan.
Penutup Meteran hitam kiri dilepas terlebih dahulu. Karena kabel dimasukkan ke dalam wadah berbentuk seperti [ di dalam ] tas, kabel tersebut dikeluarkan di dalamnya dan dibuat tenggelam di bawah Coupler di dalamnya. Kemudian, pekerjaan terminasi hanya dengan menaikkan Tangki (caranya tertulis pada instruksi manual Sepeda Motor), membuat kabel penutup Samping kiri terputus, dan terakhir menghubungkan kabel merah muda panjang ke Coupler beserta Harness Utama di bawah Tangki di melalui dan terakhir. Karena kabel merah muda cukup panjang mati menit terakhir, perlu untuk membuat posisi di mana tidak mengganggu ketika roda diputar. Jika itu adalah arah yang memungkinkan penyolderan karena tidak menjadi masalah jika melebihi 5 cm lagi, itu dapat menghubungkan untuk waktu yang lama dengan mudah.
Bagaimanapun, lampiran itu mudah dan pekerjaan selesai dalam waktu sekitar 30 menit. Meskipun itu benar, ketika [ yang dapat ditingkatkan tergantung pada jenis kendaraan ] itu adalah CB1300SB, tidak dikatakan demikian dan hanya Pembatas kecepatan yang dipotong murni.