- Beranda
- Ulasan Produk
- Sparepart Motor
- Suspensi / Rearset / Velg / Swingarm
- As Swingarm
- Penggantian poros pivot untuk 2021MT-09SP... (KOOD: Pivot Axle Shaft)
【KOOD】Pivot Axle Shaft Review
Pivot shaft replacement for 2021MT-09SP
Pivot shafts for the 2021MT-09SP, which were backordered, have been delivered and we immediately replaced them.
However, it is a simple work to loosen the nut, replace the shaft, and tighten the nut with the specified torque. I put the footpeg on the footpeg as shown in the 6th picture and the rear tire is supported by the tire clamps.
The nut is Torque 105N tightened, so it was loosened quickly with an impact wrench.
Shaft is supposed to be 0G, but I could not pull it out by hand. I lightly tapped it with a plastic hammer and it was tight only at first and then I could pull it out by hand.
Next, after applying a thin layer of grease to the shaft made by KOOD for replacement, I inserted the shaft into the pivot hole, but the hole position seemed to gap slightly on the Left Side of the body and it did not go in until the end. I tried to lift up the Rear Thailand and push it to the Left Side, but it didn't work well, and I thought it is not recommended to do so because I have another work to do. (Sweat).
At any rate, now that the Shaft is Penetrating, the Nut is tightened at the specified Torque to complete the process.
It seems that Thread compound application is recommended for Nut to prevent galling.
I have only done some light driving in the city, but to be honest, I have not noticed any large changes like I did when I replaced the front axle.
However, now that we finally have Front, Rear, and Pivot made by KOOD, I feel Refreshing.
Perhaps a comparison of riding with OEMShaft and replacement, or replacing all three at once, would make the difference feel more Large.
We replaced the Front first, then the Rear, and finally the Pivot, so we may have become accustomed to the changes.
Compared to OEM products, Pivot shafts have a very high level of precision and quality, and can be expected to provide a sense of ground contact and rigidity, but I still thought that Pivot shafts are a little difficult to afford in terms of cost.
Penggantian poros pivot untuk 2021MT-09SP
Poros pivot untuk 2021MT-09SP, yang dipesan kembali, telah dikirimkan dan kami segera menggantinya.
Namun, ini adalah pekerjaan sederhana untuk mengendurkan mur, mengganti poros, dan mengencangkan mur dengan torsi yang ditentukan. Footpeg saya pasang di footpeg seperti di gambar ke 6 dan ban belakang ditopang oleh penjepit ban.
Murnya dikencangkan dengan Torsi 105N, sehingga dilonggarkan dengan cepat dengan kunci pas benturan.
Shaft seharusnya 0G, tapi saya tidak bisa mencabutnya dengan tangan. Saya dengan ringan mengetuknya dengan palu plastik dan hanya kencang pada awalnya dan kemudian saya bisa menariknya keluar dengan tangan.
Selanjutnya setelah diolesi grease tipis-tipis pada shaft buatan KOOD untuk penggantian, saya masukkan shaft ke dalam lubang pivot, tetapi posisi lubangnya seperti ada celah sedikit di Sisi Kiri body dan tidak masuk sampai akhir. Saya mencoba mengangkat Thailand Belakang dan mendorongnya ke Sisi Kiri, tetapi tidak berhasil dengan baik, dan saya pikir tidak disarankan untuk melakukannya karena ada pekerjaan lain yang harus saya lakukan. (Keringat).
Bagaimanapun, sekarang Poros Menembus, Mur dikencangkan pada Torsi yang ditentukan untuk menyelesaikan proses.
Tampaknya aplikasi kompon Thread direkomendasikan untuk Nut untuk mencegah menyakitkan.
Saya hanya melakukan sedikit mengemudi di dalam kota, tapi sejujurnya, saya belum melihat perubahan besar seperti yang saya lakukan saat mengganti gardan depan.
Namun, sekarang kami akhirnya memiliki Front, Rear, dan Pivot yang dibuat oleh KOOD, saya merasa Menyegarkan.
Mungkin perbandingan berkendara dengan OEMShaft dan penggantian, atau mengganti ketiganya sekaligus, akan membuat perbedaannya terasa lebih Besar.
Kami mengganti Depan dulu, lalu Belakang, dan terakhir Pivot, jadi kami mungkin sudah terbiasa dengan perubahan itu.
Dibandingkan dengan produk OEM, poros Pivot memiliki tingkat presisi dan kualitas yang sangat tinggi, dan dapat diharapkan untuk memberikan kesan kontak tanah dan kekakuan, tetapi saya masih berpikir bahwa poros Pivot agak sulit untuk dibeli dalam hal biaya.