- Beranda
- Ulasan Produk
- Sparepart Motor
- Rantai / Gear
- Sprocket Depan
- Sprocket Depan
- Bore up lalu efek Outclassing.... (KITACO: Drive Sprocket)
【KITACO】Drive Sprocket Review
Sesuai: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-S125, SUZUKI Gixxer 150.
Bore up and then the effect Outclassing.
I wanted to get closer and closer to SUPER CUB 90 (laughs).
Driven Sprocket was changed to 14→15.
[Sprocket's role].
Sprocket‥
What is Sprocket? Sprocket." The gear-like parts in the center of the wheel of a tire that transmit the engine's power to the tire.
Driven Sprocket‥
It is one of the essential parts to transmit the rotation of the engine to the saw chain.
The word drive (drive) is, Driving." Although it is widely known to mean, "Driven." does not translate as 。 In fact, the Drive has a Drives the ~." means.
■Change the number of Driven Sprocket hits.
High Speed Oriented
Lower Fat → Focus on acceleration
*I would say that raising the number to 14 →15 guns this time is the most High Speed Oriented.
■ Replacement procedure (for CUB)
(1) Remove the chain cover.
Remove the Side Cover and Chain Cover.
The side cover can be removed with a large-trimmed slotted screwdriver.
↓
Remove the chain cover, and note that there are four 10mm bolts and one bolt next to the rear shock has a different bolt length.
↓
? Remove Bolt of Chain Cover with Glasses Wrenchetc.
↓
(4) The upper part of the Chain Cover is removed by pulling it up at a right angle.
↓
(5) Next, remove the lower part of the Chain Cover as well.
↓
(6) Set the Chain play to the Most Large.
To use an analogy, it is a dull state.
When only the front sprocket is used, the chain does not need to be removed and is Large sturdy.
↓
(7) Replace the Driven Sprocket.
First, remove the Change Pedal.
*The fixed Bolt is located at the base of the mounting shaft.
↓
Remove the Bolt for fixing the Pedal with a 10mm Wrench (?).
↓
Next, remove the Crank Case Cover. There are three fixed bolts.
↓
Remove the fixed Bolt of the Crank Case Cover with a ? 8mm socket wrench.
↓
When the 11 (11) Cover is removed, the Driven Sprocket appears.
↓
Remove the Bolt with a ?10mm Wrench and remove the fixed Plate of the Sprocket.
↓
Install the ? new Driven Sprocket aligning it with the groove. Insert the Fixing Plate in line with the groove in the middle of the mounting shaft, and turn it slightly to align it with the Screw hole.
↓
?After that, tighten the Bolt firmly and install the Sprocket.
☆ Effect ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ Effect
◎Maximum speed has increased, from 80 to 85 and beyond.
◎The second speed is easier to use.
Changed from 2nd gear → hill only to 2nd gear → medium speed cruising.
Work Precautions
When touching Sprocket, bare hands are dis→ed.
● The work process is tedious because there are many work processes.
Since it is related to power, I think there is little demerit in replacing it.
Even if the power is increased by bore-up, it is a waste of power if the power is not transferred to the drivetrain parts.
The reverse idea is that if the low-speed Torque is too weak, we can lower the number of hits.
Bore up lalu efek Outclassing.
Saya ingin semakin dekat dengan SUPER CUB 90 (tertawa).
Sprocket yang Digerakkan diubah menjadi 14→15.
[Peran Sproket].
Sproket‥
Apa itu Sproket? Sproket." Bagian seperti roda gigi di tengah roda ban yang menyalurkan tenaga mesin ke ban.
Sproket yang Digerakkan‥
Merupakan salah satu bagian penting untuk menyalurkan putaran mesin ke rantai gergaji.
Kata drive (drive) adalah, Driving." Meskipun secara luas diketahui artinya, "Driven." tidak diterjemahkan sebagai 。 Faktanya, Drive memiliki arti Drives the ~.".
■Ubah jumlah pukulan Driven Sprocket.
Berorientasi Kecepatan Tinggi
Menurunkan Lemak → Fokus pada akselerasi
*Menurut saya, menaikkan jumlahnya menjadi 14 →15 senjata kali ini adalah yang paling Berorientasi Kecepatan Tinggi.
■ Prosedur penggantian (untuk CUB)
(1) Lepaskan penutup rantai.
Lepaskan Penutup Samping dan Penutup Rantai.
Penutup samping dapat dilepas dengan obeng berlubang besar.
↓
Lepaskan penutup rantai, dan perhatikan ada empat baut berukuran 10mm dan satu baut di sebelah shock belakang memiliki panjang baut yang berbeda.
↓
? Lepas Baut Penutup Rantai dengan Kunci Pas Kacamata, dll.
↓
(4) Bagian atas Penutup Rantai dilepas dengan cara menariknya ke atas tegak lurus.
↓
(5) Selanjutnya, lepaskan juga bagian bawah Penutup Rantai.
↓
(6) Atur permainan Rantai ke Paling Besar.
Sebagai analogi, ini adalah keadaan yang membosankan.
Jika yang digunakan hanya sproket depan, rantai tidak perlu dilepas dan berukuran besar kokoh.
↓
(7) Pasang kembali Sproket yang Digerakkan.
Pertama, lepaskan Pedal Ganti.
*Baut tetap terletak di dasar poros pemasangan.
↓
Lepas Baut Pengikat Pedal dengan Kunci Pas 10mm (?).
↓
Selanjutnya, lepas Penutup Kotak Engkol. Ada tiga baut tetap.
↓
Lepas Baut Tetap Penutup Kotak Engkol dengan ? Kunci pas soket 8mm.
↓
Saat Penutup 11 (11) dilepas, Sproket Penggerak akan muncul.
↓
Lepaskan Baut dengan Kunci Pas ?10mm dan lepaskan Pelat Tetap Sproket.
↓
Instal ? Sproket Berpenggerak baru yang menyelaraskannya dengan alur. Masukkan Pelat Pengikat sejajar dengan alur di tengah poros pemasangan, dan putar sedikit agar sejajar dengan lubang Sekrup.
↓
?Setelah itu kencangkan Baut dengan kuat dan pasang Sproket.
☆ Efek ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ ☆ Efek
◎Kecepatan maksimum meningkat, dari 80 menjadi 85 dan seterusnya.
◎Kecepatan kedua lebih mudah digunakan.
Berubah dari gigi 2 → bukit saja ke gigi 2 → jelajah kecepatan sedang.
Tindakan Pencegahan Kerja
Saat menyentuh Sproket, tangan kosong akan terdis→.
● Proses kerja membosankan karena banyak proses kerja.
Karena berkaitan dengan kekuasaan, menurut saya tidak ada salahnya menggantinya.
Sekalipun tenaga ditingkatkan dengan bore-up, namun akan membuang-buang tenaga jika tenaga tidak disalurkan ke bagian drivetrain.
Gagasan sebaliknya adalah jika Torsi kecepatan rendah terlalu lemah, kita dapat menurunkan jumlah pukulan.