- Beranda
- Ulasan Produk
- Sparepart Motor
- Rangka
- Dudukan / Sambungan Standar Samping
- Akurasi pemasangannya buruk... (R&G: Stand Height Bracket [Kickstand Shoe])
【R&G】Stand Height Bracket [Kickstand Shoe] Review
Sesuai: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA), SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
The mounting accuracy is bad
GSX 1300 R HAYABUSA has a large slope when stopping at Side Stand, so weigh down when raising
I bought it in the summer to prevent STAND from getting into Asphalt.
Mounting is essentially just fitting and tightening 3 Screws.
However, unfortunately it is not possible to enter either STAND or product.
I deleted STAND with Grinder.
Since the depth is small and the STAND does not run even after cutting it, it is impossible to put on the top covering?.
You can not install it unless you cut the depth of the product or cut the back of the STAND to thin it.
I built my own Spacer in between.
Another Bolt was necessary because the Bolt's Length is insufficient with Spacer's thickness.
It may be different depending on the type of car, but I did not buy it if I knew that it was necessary to process this much.
If you are not confident in machining tools or machining, I think that you should ask Shop for installation.
Nice place
- You do not have to take things to lay under STAND in the summer.
- Since the STAND becomes longer by about 5 mm, it is easier to wake it from the time of stopping.
A bad place
- The mounting accuracy is very bad..
- Price is too high.
Others
- For vehicles that are Lowdown by footbed countermeasure, STAND is about 5 mm but it gets longer.
- If there is an Exhaust System on the side where the Side Stand is located there is a possibility of contact during storage.
- It takes a car weight and contacts the ground so it's a bit sad to be scratched (Lol)
Akurasi pemasangannya buruk
GSX 1300 R HAYABUSA memiliki kemiringan yang besar saat berhenti di Side Stand, jadi turunkan beban saat menaikkan
Saya membelinya di musim panas untuk mencegah STAND masuk ke Asphalt.
Pemasangan pada dasarnya hanya memasang dan mengencangkan 3 Sekrup.
Namun, sayangnya tidak memungkinkan untuk memasukkan STAND atau produk.
Saya menghapus STAND dengan Grinder.
Karena kedalamannya kecil dan STAND tidak berjalan bahkan setelah dipotong, tidak mungkin untuk memasang penutup atas?.
Anda tidak dapat memasangnya kecuali Anda memotong kedalaman produk atau memotong bagian belakang STAND untuk mengencerkannya.
Saya membangun Spacer saya sendiri di antaranya.
Baut lain diperlukan karena Panjang Baut tidak mencukupi dengan ketebalan Spacer.
Mungkin berbeda tergantung jenis mobilnya, tetapi saya tidak membelinya jika saya tahu perlu memproses sebanyak ini.
Jika Anda tidak yakin dengan alat permesinan atau permesinan, saya pikir Anda harus meminta Toko untuk memasangnya.
Tempat yang bagus
- Anda tidak perlu mengambil barang untuk diletakkan di bawah STAND di musim panas.
- Karena STAND menjadi lebih panjang sekitar 5 mm, lebih mudah untuk membangunkannya dari waktu berhenti.
Tempat yang buruk
- Akurasi pemasangan sangat buruk..
- Harga terlalu tinggi.
Yang lain
- Untuk kendaraan yang Lowdown dengan footbed countermeasure, STAND sekitar 5 mm tetapi menjadi lebih panjang.
- Jika terdapat Sistem Pembuangan di samping tempat Penyangga Samping berada, ada kemungkinan kontak selama penyimpanan.
- Butuh bobot mobil dan menyentuh tanah jadi agak sedih tergores (Lol)