- Beranda
- Ulasan Produk
- Sparepart Motor
- Sparepart Stang & Kemudi
- Stang
- Kelelahan lengan membuat sangat mudah.... (HURRICANE: Handle For Bolt)
【HURRICANE】Handle For Bolt Review
The tiredness of the arm makes considerably easy.
Bolt RSpecifications attached to ABS.
I think I just came in front of you, but even with that alone pretty much the posture itself became easier.
I have not installed it yet, so I am not riding long distances, but I am likely to reduce the tiredness of my arms.
This time, I tried my best and I challenged to install.
Since there is no Instruction Manual, I removed it while watching the Service Manual but as I tried following the Service Manual, "You did not have to get off that far ..." There were some parts called.
Manual In order as described,
■ Removing Headlight. Horizontal screws (3. 8Nm)Quantity : Remove Lens with 2pc. Two couplers inside, disconnect, screw (7Nm) Remove all with 3. ... It seems that Headlight does not need to be removed. If there is any trouble with the removal after this please remove.
■ Removing Back Mirror. ? ? ? It is possible to do without doing this, but it is worried about dropping and scratching so it is better to remove them. As Yamaha, please note that Right's Mirror is reverse threaded.
■ Front brakeLightSwitch connector removed. Quantity under Brake master cylinder : 2pc Connector. You can pull it out. ? ? ? It seems that even without doing this.
■Front brakes master cylinderHolder. Quantity : 2pc screw (10Nm) It will be out.
■RightHandlebar switch. Quantity : 2 pc screw (3. 5 Nm) Open with spur. In the Manual, you will also remove the Throttle Cable, but leave it as it is below (Other than Handlebar grip) It is best to remove as it is after removing.
■Clutch switchCoupler. Coupler disconnect under LeftHandlebar switch.
■LeftHandlebar switch. Quantity : 2 pc screw (3. 5 Nm) Open it up and remove it.
■Handlebar grip. This is an idiot. It is hard to get out. It is postponement.. After removing all other parts, I tried and errored carefully. In Manual "Blowing compressed air into the gap" Although it is written, since there is no Compressor, in the end, I rolled off from the edge and removed it with power while making it into a Doughnut shape. I feel this is the best. It's a quite resilient Rubber.
■Clutch Cable - Clutch lever. If you do not remove it, RightHandlebar will not come out. Remove the Clutch lever while removing it.
■Clutch switch. ? ? ? It is not removed.
■Clutch lever holder. One screw in front (10Nm). After removing the Handlebar grip, remove it.
■MeterAss'yBracket. Meter got in the way, Upper Handlebar holder (Main's Handlebar fixed Bolt near Center) Because you can not remove the screw of the Meter bottom screw (7Nm) Quantity : Remove only 2 pc so we can shift Meter. Protect Tank across Cushion.
■ Upper Handlebar Holder 2 places. screw (28Nm) Total 4.
Now that you can remove the Handlebar. Unplug the Right Handlebar Throttle, remove the Left Handbar grip and remove the Clutch lever holder.
The above is the removal procedure, "It does not have to be removed" Even if I wrote it, perhaps it might interfere with others, so please remove it then.
And install this Handlebar of HURRICANE in the reverse order of removal.
I forgot to take a picture. Although there is no picture,
Those who are aiming for DIY, please do their best..
Kelelahan lengan membuat sangat mudah.
Baut RSpesifikasi terpasang pada ABS.
Saya pikir saya baru saja datang di depan Anda, tetapi bahkan dengan itu saja, postur itu sendiri menjadi lebih mudah.
Saya belum memasangnya, jadi saya tidak berkendara jarak jauh, tetapi saya cenderung mengurangi kelelahan lengan saya.
Kali ini, saya mencoba yang terbaik dan saya tertantang untuk menginstal.
Karena tidak ada Instruksi Manual, saya menghapusnya saat menonton Manual Servis tetapi ketika saya mencoba mengikuti Manual Servis, "Anda tidak harus turun sejauh itu ..." Ada beberapa bagian yang disebut.
Manual Sesuai dengan yang dijelaskan,
Melepaskan Lampu Depan. Sekrup horizontal (3. 8Nm)Jumlah : Lepas Lensa dengan 2pc. Dua skrup di dalam, lepaskan, sekrup (7Nm) Lepas semua dengan 3. ... Tampaknya Lampu Depan tidak perlu dilepas. Jika ada masalah dengan penghapusan setelah ini, silakan hapus.
Menghapus Cermin Belakang. ? ? ? Dimungkinkan untuk melakukannya tanpa melakukan ini, tetapi khawatir akan jatuh dan tergores sehingga lebih baik untuk menghapusnya. Sebagai Yamaha, harap dicatat bahwa Kaca Spion Kanan memiliki ulir terbalik.
Rem depan Konektor LightSwitch dilepas. Jumlah di bawah Rem master silinder: 2 pc Konektor. Anda bisa menariknya keluar. ? ? ? Tampaknya bahkan tanpa melakukan ini.
Pemegang silinder master rem depan. Jumlah: 2pc sekrup (10Nm) Ini akan keluar.
Sakelar Stang Kanan. Jumlah : 2 buah sekrup (3. 5 Nm) Buka dengan taji. Dalam Manual, Anda juga akan melepas Kabel Throttle, tetapi biarkan seperti di bawah (Selain pegangan Handlebar) Sebaiknya lepaskan apa adanya setelah melepas.
Clutch switchCoupler. Putuskan coupler di bawah sakelar LeftHandbar.
Sakelar Stang Kiri. Jumlah : 2 buah sekrup (3. 5 Nm) Buka dan lepaskan.
Pegangan stang. Ini adalah idiot. Sulit untuk keluar. Ini adalah penundaan.. Setelah melepas semua bagian lain, saya mencoba dan melakukan kesalahan dengan hati-hati. Dalam Manual "Menghembuskan udara terkompresi ke celah" Meskipun tertulis, karena tidak ada Kompresor, pada akhirnya, saya berguling dari tepi dan mengeluarkannya dengan kekuatan sambil membuatnya menjadi bentuk Donat. Saya merasa ini yang terbaik. Ini adalah Karet yang cukup tangguh.
Kabel Kopling - Tuas kopling. Jika Anda tidak menghapusnya, RightHandbar tidak akan keluar. Lepaskan tuas Kopling saat melepasnya.
Sakelar kopling. ? ? ? Hal ini tidak dihapus.
Pemegang tuas kopling. Satu sekrup di depan (10Nm). Setelah melepas pegangan Handlebar, lepaskan.
MeterAss'yBracket. Meter menghalangi, dudukan Stang Atas (Baut Stang Utama tetap dekat Pusat) Karena Anda tidak dapat melepas sekrup sekrup bawah Meter (7Nm) Jumlah : Lepas hanya 2 pc sehingga kami dapat menggeser Meter. Lindungi Tangki di seluruh Cushion.
Dudukan Stang Atas 2 tempat. sekrup (28Nm) Jumlah 4.
Sekarang Anda dapat menghapus Handlebar. Cabut Throttle Handlebar Kanan, lepaskan pegangan Handbar Kiri dan lepaskan penahan tuas Kopling.
Di atas adalah prosedur penghapusan, "Tidak harus dihapus" Bahkan jika saya menulisnya, mungkin mengganggu orang lain, jadi tolong hapus saja.
Dan pasang Handlebar of HURRICANE ini dengan urutan pelepasan terbalik.
Saya lupa mengambil gambar. Meskipun tidak ada gambar,
Yang membidik DIY, tolong lakukan yang terbaik..