- Beranda
- Ulasan Produk
- Sparepart Motor
- Rantai / Gear
- Sparepart Skutik
- Sparepart Skutik
- Set Pulley / Drive Kit Skutik
- Sesuai dengan reputasi!... (MALOSSI: Multi-Variator 2000)
【MALOSSI】Multi-Variator 2000 Review
According to reputation!
It's an exchange from ZERO's High Speed ??Pulley SS.
First of all, there are some BALI inside Pulley about installation. Also, Slide Piece is hard to move. There is slight BALI on the outside of the Ramp PlateRoller side.
Before installing, it is necessary to shave BALI and Slide Piece a little to improve movement.
The attached WR is written as 7 g. I hope not to use it, but (Lol)
As Belt also exchanged together this time, I think that it will not be evaluated only by Pulley, but installation improved and accelerating improved from the start clearly at the Belt companion stage.
WR used DrPulley and it was 5 g when Zero's Pulley was 5. Even if it weighs as much as 5 g it will accelerate and it will accelerate even a little richer uphill.
Also at the time of Pulley of ZERO, 2 mm color was added to a 36 mm boss and it was made long to 38 mm and it was pretty much dropped Belt, but this time put the attached 2 mm color into the Ramp Plate back to the Instruction Manual and put on the Pulley 36. I put a 5 mm boss.
I thought that the start and acceleration will fall as the Belt is not dropped, but on the contrary it got much better.
Although I can not evaluate fully-open running at the beginning of Belt's familiarization yet, I still think that Pulley can experience a considerable difference.
Both ZERO's Pulley and KITACO's Power drive kit are also used, but both are dissatisfied, but I think Malossi is the best in Total.
ZERO is getting a bit worse unless Belt is dropped at a high rotation speed and KITACO falls at the highest speed with low speed to acceleration focus.
Although I am high, though I thought that if I first added Malossi, it was cheaper to do it.
Sesuai dengan reputasi!
Ini adalah pertukaran dari High Speed ??Pulley SS ZERO.
Pertama-tama, ada beberapa BALI di dalam Pulley tentang pemasangan. Juga, Slide Piece sulit untuk dipindahkan. Ada sedikit BALI di bagian luar sisi Ramp PlateRoller.
Sebelum memasang, perlu sedikit mencukur BALI dan Slide Piece untuk meningkatkan gerakan.
WR terlampir ditulis sebagai 7 g. Saya harap tidak menggunakannya, tapi (Lol)
Karena Belt juga dipertukarkan bersama kali ini, saya pikir itu tidak akan dievaluasi hanya oleh Pulley, tetapi pemasangan ditingkatkan dan akselerasi ditingkatkan dari awal dengan jelas pada tahap pendamping Belt.
WR menggunakan DrPulley dan itu 5 g ketika Zero's Pulley adalah 5. Bahkan jika beratnya sebanyak 5 g, itu akan berakselerasi dan akan berakselerasi bahkan sedikit lebih kaya menanjak.
Juga pada saat Pulley of ZERO, warna 2 mm ditambahkan ke bos 36 mm dan dibuat panjang menjadi 38 mm dan itu cukup banyak menjatuhkan Belt, tetapi kali ini masukkan warna 2 mm yang terpasang ke Ramp Plate kembali ke Instruksi Manual dan memakai Katrol 36. Saya memasang bos 5 mm.
Saya pikir start dan akselerasi akan turun karena Sabuk tidak dijatuhkan, tetapi sebaliknya menjadi jauh lebih baik.
Meskipun saya belum dapat mengevaluasi lari terbuka penuh pada awal pengenalan Belt, saya masih berpikir bahwa Pulley dapat mengalami perbedaan yang cukup besar.
Baik ZERO's Pulley dan Power drive kit KITACO juga digunakan, tetapi keduanya tidak puas, tapi menurut saya Malossi adalah yang terbaik di Total.
NOL menjadi sedikit lebih buruk kecuali Sabuk dijatuhkan pada kecepatan putaran tinggi dan KITACO jatuh pada kecepatan tertinggi dengan kecepatan rendah untuk fokus akselerasi.
Meskipun saya tinggi, meskipun saya pikir jika saya pertama kali menambahkan Malossi, lebih murah untuk melakukannya.