- Beranda
- Ulasan Produk
- Sparepart Motor
- Bodywork
- Spakbor
- Fender Eliminator
- Ini padat dan memiliki tekstur yang baik.... (ACTIVE: Fender Eliminator Kit)
【ACTIVE】Fender Eliminator Kit Review
It is solid and has a good texture.
At first, I had installed CHINA's cheap Fender Eliminator Kit, but the hole to install the blinker was too large and the hole was noticeable even after installing the blinker (you could see the other side), and the LED License Plate Light was too large and looked cheap. I replaced it with this one because I didn't like the cheap-looking feeling of the Large License Plate and the Clearance on the side of the car body.
Installation is not particularly difficult. First, pull out the Coupler, which integrates the Blinker and License Plate Light wiring, then remove the OEM Rear Fender, and you are halfway through the installation process.
All that is left to do is to install the equipment in accordance with the Instruction Manual, which is not difficult at all, so I would like to encourage custom beginners to give it a try.
However, the instruction manual included in the package is white-black and difficult to understand, so it is better to use the PDF version of the instruction manual, which can be downloaded in color by accessing the Active homepage from your smartphone.
I wish they would have included a color printed Instruction Manual from the beginning... but I am thankful that a color version is available. I think this is a good measure to lower the Hurdle of installation.
It is an aluminum Fender Eliminator and costs close to 20,000 yen, but the quality is good because of its high price.
I especially like the elegant way the License Plate Light shines, where the light source is not fully visible.
However, I personally prefer the License Plate to be a little closer to the body of the vehicle, and the License Plate should be laid down to the limit, although it is legally regulated. Also, it would have been better if there was some kind of improvement to plug the holes where the Blinker and License Plate Light wirings are pulled into the body of the car. But it is a Large Merit that can pass the inspection as it is.
*Reflector is not included and must be purchased separately.
The S1000RR after 2015 seems to have a slightly different image than the Wiring color in the instruction manual.
Also, when I disconnected and connected the OEM License Plate Light Wiring to power the LED License Plate Lamp that was included in the CHINA Fender Eliminator Kit, it came on at first but soon stopped working.
Then I connected the License Plate Light of this product to the OEM License Plate LightWiring and it did not light up. I had no choice but to branch off from the ETC power supply and Wiring.
Ini padat dan memiliki tekstur yang baik.
Pada awalnya, saya telah memasang Fender Eliminator Kit murah dari CHINA, tetapi lubang untuk memasang tanda bahayanya terlalu besar dan lubangnya terlihat bahkan setelah memasang tanda bahayanya (Anda dapat melihat sisi lain), dan Lampu Plat Nomor LED terlalu besar dan tampak murah. Saya menggantinya dengan yang ini karena saya tidak suka kesan murahan dari Plat Nomor Besar dan Jarak Bebas di samping badan mobil.
Instalasi tidak terlalu sulit. Pertama, cabut Coupler, yang mengintegrasikan kabel Blinker dan License Plate Light, kemudian lepaskan Fender Belakang OEM, dan Anda sudah setengah jalan dalam proses pemasangan.
Yang perlu dilakukan hanyalah memasang peralatan sesuai dengan Instruksi Manual, yang tidak sulit sama sekali, jadi saya ingin mendorong pemula untuk mencobanya.
Namun, manual instruksi yang disertakan dalam paket berwarna putih-hitam dan sulit dipahami, jadi lebih baik menggunakan manual instruksi versi PDF, yang dapat diunduh berwarna dengan mengakses beranda Active dari ponsel cerdas Anda.
Saya berharap mereka menyertakan Instruksi Manual yang dicetak berwarna sejak awal... tetapi saya bersyukur bahwa versi berwarna tersedia. Saya pikir ini adalah ukuran yang baik untuk menurunkan Rintangan instalasi.
Ini adalah Fender Eliminator aluminium dan harganya mendekati 20.000 yen, tetapi kualitasnya bagus karena harganya yang tinggi.
Saya terutama menyukai cara bersinar Lampu Plat Nomor yang elegan, di mana sumber cahaya tidak sepenuhnya terlihat.
Namun, saya pribadi lebih suka Plat Nomor sedikit lebih dekat dengan badan kendaraan, dan Plat Nomor harus diletakkan hingga batasnya, meskipun diatur secara hukum. Juga, akan lebih baik jika ada semacam perbaikan untuk menutup lubang di mana kabel Blinker dan Lampu Plat Nomor ditarik ke badan mobil. Tapi itu adalah Pahala Besar yang bisa lolos pemeriksaan apa adanya.
*Reflektor tidak termasuk dan harus dibeli secara terpisah.
S1000RR setelah 2015 tampaknya memiliki gambar yang sedikit berbeda dari warna Wiring di buku petunjuk.
Juga, ketika saya memutuskan dan menyambungkan Pengabelan Lampu Plat Nomor OEM untuk menyalakan Lampu Plat Nomor LED yang termasuk dalam CHINA Fender Eliminator Kit, awalnya menyala tetapi segera berhenti bekerja.
Kemudian saya menghubungkan Lampu Plat Nomor produk ini ke Lampu Plat Nomor OEM dan tidak menyala. Saya tidak punya pilihan selain bercabang dari power supply ETC dan Wiring.